3One data IES7110 Series Manuel utilisateur

IES7110 Series

Managed Industrial Ethernet Switch

Quick Installation Guide

3onedata Co., Ltd.

Address:

3/B, Zone 1, Baiwangxin High Technology

Industrial Park, Xili, Nanshan District,

Shenzhen

Website:

www.3onedata.com

Tel:

+86 0755-26702688

Fax:

+86 0755-26703485

【Package checklist】

Please check whether the package and accessories are intact

while using the switch for the first time.

Industrial Ethernet switch

Certification

Quick installation guide

Warranty card

DIN-Rail mounting attachment

Power line (standard

configuration of AC equipment)

If any of these items are damaged or lost, please contact our

company or dealers, we will solve it ASAP.

【Product Overview】

This series are 100M/Gigabit managed DIN-Rail industrial

Ethernet switch. Models as follows:

Model I. IES7110-2GS-P (12～48VDC) (2 Gigabit SFP + 8

100M copper ports + 2 12~48VDC power supplies)

Model II. IES7110-2GS-P (100～240VAC/DC) (2 Gigabit

SFP + 8 100M copper ports + 1 100~240VAC/DC power

supply)

Model III. IES7110-2GS-2F-P (12～48VDC) (2 Gigabit SFP +

6 100M copper ports + 2 100M fiber ports + 2 12~48VDC

power supplies)

Model IV. IES7110-2GS-2F-P (100～240VAC/DC) (2 Gigabit

SFP + 6 100M copper ports + 2 100M fiber ports + 1

100~240VAC/DC power supplies)

Model V. IES7110-2GS-4F-P (12～48VDC) (2 Gigabit SFP +

4 100M copper ports + 4 100M fiber ports + 2 12~48VDC

power supplies)

Model VI. IES7110-2GS-4F-P (100～240VAC/DC) (2 Gigabit

SFP + 4 100M copper ports + 4 100M fiber ports + 1

100~240VAC/DC power supply)

Model VII. IES7110-3GS-P (12～48VDC) (3 Gigabit SFP + 7

100M copper ports + 2 12~48VDC power supplies)

Model VIII. IES7110-3GT-P (12～48VDC) (3 Gigabit

copper ports + 7 100M copper ports + 2 12~48VDC power

supplies)

【Panel design】

Rear view, Top view and Bottom view

Front view of DC products

Model I Model III Model V

Model VII Model VIII

Front view of AC products

Model II Model IV Model VI

1. DIN-Rail mounting kit

2. Grounding screw

3. Relay alarm output terminal block

4. Console port

5. DC dual power supply input terminal block

6. DIP switch

7. AC single power supply input terminal block

8. Relay alarm indicator ALM/Alarm

9. Power supply input status indicator P1/P2/PWR

10. Device running indicator RUN

11. 100M Ethernet port connection indicator

12. Gigabit Ethernet port connection indicator

13. 1000Base-SFP Ethernet SFP slot

14. 10/100Base-TX Ethernet copper port

15. 100Base-FX Ethernet fiber port

16. 10/100/1000Base-T(X) Ethernet copper port

【Mounting Dimension】

Unit: mm

Attention before mounting:

Don't place or install the device in area near water or

moist, keep the relative humidity of the device

surrounding between 5%~95% without condensation.

Before power on, first confirm the supported power

supply specification to avoid over-voltage damaging the

device.

The device surface temperature is high after running;

please don't directly contact to avoid scalding.

【DIN-Rail Mounting】

For convenient usage in industrial environments, the product

adopts 35mm DIN-Rail mounting, mounting steps as below:

Check whether the DIN-Rail mounting kit thatStep 1 comes with the device is installed firmly.

Insert the bottom of DIN-Rail mounting kit (one sideStep 2 with spring support) into DIN-Rail, and then insert

the top into DIN-Rail.

Tips:

Insert a little to the bottom, lift upward and then insert

to the top.

Check and confirm the product is firmly installed onStep 3 DIN-Rail, and then mounting ends.

【Disassembling DIN-Rail】

Power off the device.Step 1 After lift the device upward slightly, first shift out theStep 2 top of DIN-Rail mounting kit, and then shift out the

bottom of DIN-Rail, disassembling ends.

Attention before powering on:

Power ON operation: first connect power line to the

connection terminal of device power supply, and then

power on.

Power OFF operation: first unpin the power plug, and

then remove the power line, please note the operation

order above.

【Power Supply Connection】

DC dual power supply

The products of model I, model III,

model V, model VII and model VIII

support DC dual power supply. And they

provide 4 pins power input terminal

blocks and two independent DC power

supply systems of PWR1 and PWR2.

The power supply supports nonpolarity and anti-reverse

connection. It can normally operate after reverse connection.

Power supply range: 12～48VDC

AC single power supply

The products of model II, model IV and

model VI support AC single power

supply and provide 4 pins 7.62mm pitch

power input terminal blocks. The definitions of terminal blocks

as follows: N/-, PG, L/+.

Power supply range: 100～240VAC/DC.

【Relay Connection】

Relay terminal blocks are a pair of normally

open contacts in the alarm relay of the device.

They are open circuit in the status of normal no

alarm, and closed when any warning message occurs. For

example: they are closed and send out alarm when power off.

The product supports 1 relay warning message output, and

warning messages output of the DC power supply or network

abnormal alarm output. It can be connected to alarm indicator,

alarm buzzer, or other switching value collecting devices for

timely warning operating staffs when the warning message

occurs.

【DIP Switch Settings】

The product provides 4 pins DIP switch for

function settings, where "ON" is the enable valid

terminal. Please power on again before

changing the DIP switch status.

DIP switch definitions as follows:

DIP

Definition

Operation

reserved

Restore factory

defaults

Set the DIP switch to ON, the

device will automatically

restore factory defaults, and

then turn off the DIP switch.

Upgrade

Set the DIP switch to ON for

upgrading the device, and

then turn it off.

Reserved

【Console Port Connection】

The device provides 1 procedure debugging port based on

serial port, and can manage the CLI command line of the

device after connected to PC. The interface adopts RJ45 port,

the RJ45 pins definition as follows:

Pin No.

Definition

TXD

RXD

GND

【Checking LED Indicator】

The function of each LED is described in the table as below:

LED

Status

Description

PWR/P1/P

Power supply is connected and

running normally

OFF

Power supply is disconnected and

running abnormally.

ALM/Alarm

Power supply and port link alarm

OFF

Power supply and port link without

alarm

RUN

The device is powering on or

abnormal.

OFF

The device is powered off or

abnormal.

Blinking

Blink once per second, the device

is running well.

Link/ACT

(1-7/8,G1-

G2/G3)

Ethernet port connection is active.

Blinking

Data transmitted

OFF

Ethernet port connection is

inactive.

【Logging in to WEB Interface】

This device supports WEB management and configuration.

Computer can access the device via Ethernet interface. The

way of logging in to device’s configuration interface via IE

browser is shown as below:

Configure the IP addresses of computer and theStep 1 device to the same network segment, and the

network between them can be mutually accessed.

Enter device’s IP address in the address bar of theStep 2 computer browser.

Enter device’s username and password in the loginStep 3 window as shown below.

Click “OK”button to login to the WEB interface ofStep 4 the device.

Note:

The default IP address of the device is “192.168.1.254”.

The default username and password of the device is

“admin”.

If the username or password is lost, user can restore it to

factory settings via device DIP switch or management

software; all modified configurations will be cleared

after restoring to factory settings, so please backup

configuration file in advance.

Please refer to user manual for specific configuration

method of logging in to WEB interface and other

configurations about network management function.

【Specification】

Panel

Gigabit SFP

1000Base-SFP, SFP slot

Gigabit copper port

10/100/1000Base-T(X)

self-adapting RJ45 port, full/half

duplex self-adaption or specified

operating mode, support

MDI/MDI-X self-adaption

100M copper port

10/100Base-T(X) self-adapting

RJ45 port, full/half duplex

self-adaption or specified

operating mode, support

MDI/MDI-X self-adaption

100M fiber port

100Base-FX, optional SC/ST/FC

port

Console port

CLI command management port

(RS-232), RJ45

Alarm interface

2 pins 7.62mm pitch terminal

blocks, support 1 relay alarm

information output, the current

load capacity is 1A@24VDC

Indicator

Power indicator, running

indicator, interface indicator and

alarm indicator

Exchange attributes

Backplane bandwidth

7.6G

Packet buffer size

1Mbit

MAC table size

Power supply

Input power supply

12~48VDC or

100~240VAC/VDC

DC power supply supports dual

power supply redundancy,

nonpolarity and anti-reverse

connection

Support built-in overcurrent 4.0A

or 5.0A protection

Access terminal

4 pins 7.62mm pitch terminal

blocks

Consumption

No-load

≤6.14W@24VDC

Full-load

≤9.24W@24VDC

Environmental Limits

Working temperature

-40~75℃

Storage temperature

-40~85℃

Working humidity

5%~95% (no condensation)

Protection grade

IP40 (metal shell)

Ce manuel convient aux modèles suivants

Autres manuels 3One data Routeur réseau

3One data

3One data IES5028G-8GC-4GS Manuel utilisateur

3One data

3One data IES5024-2F Manuel

3One data

3One data IES605-2D series Manuel utilisateur

3One data

3One data IES6116 Series Manuel utilisateur

3One data

3One data IES6116-2F-P Manuel utilisateur

3One data

3One data ES2010G-2GF Manuel utilisateur

3One data

3One data IES215-1F-P Manuel utilisateur

3One data

3One data IES615-2D Series Manuel utilisateur

3One data

3One data IES618-P Manuel utilisateur

3One data

3One data ICPE2600 Series Manuel utilisateur

3One data

3One data IES308 Manuel

3One data

3One data IES7110-3G Series Manuel utilisateur

3One data

3One data MES600 Series Manuel utilisateur

3One data

3One data IES3020-4GS-4F-P Manuel utilisateur

3One data

3One data IES618-4D(RS-232)-P Manuel utilisateur

3One data

3One data IES615-2D Series Manuel utilisateur

3One data

3One data MES5000 Series Manuel utilisateur

3One data

3One data IES2010-2GS-4F Manuel

3One data

3One data 7212 Manuel utilisateur

3One data

3One data IEM615 Series Instructions d'utilisation

3One data

3One data IES308-2F Manuel

3One data

3One data IRT5300-AW-5T2D Manuel utilisateur

3One data

3One data ICS5028G Series Manuel utilisateur

3One data

3One data IES7110-2GS-P Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité