ZyXEL Communications ES-116S Manuel utilisateur
ENGLISH
1
1 Introduction
The ES-116S is a 16-port switch that can be used to build
high-performance switched networks. The ES-116S is a
store-and-forward device that offers low latency for high-
speed networking.
1.1 Small Workgroup Application
The ES-116S can be used as a standalone switch to
which computers, servers and a printer are directly
connected to form a small workgroup.
2 Hardware Installation
The ES-116S is suitable for an office environment where
it can be placed on a desktop. If you want to mount it on a
wall instead, see section 5.
1Make sure the ES-116S is clean and dry.
ENGLISH
2
ENGLISH
2Set the ES-116S on a smooth, leveled and sturdy flat
space strong enough to support the weight of the ES-
116S and the connected cables. Make sure there is a
power outlet nearby.
"Do NOT block the ventilation holes.
3 Rear Panel Connections
The RJ-45 ports and the power port are located on the
rear panel.
3.1 RJ-45 Auto-negotiating Ports
The 10Base-T/100Base-TX RJ-45 ports are auto-
negotiating and auto-crossover.
An auto-negotiating port can detect and adjust to the
optimum Ethernet speed (10/100Mpbs) and duplex mode
(full duplex or half duplex) of the connected device.
An auto-crossover (auto-MDI/MDI-X) port automatically
works with a straight-through or crossover Ethernet cable.
ENGLISH
3
"Make sure the cable length between
connections does not exceed 100 meters
(328 feet).
3.2 Power
Use the included power cable to connect your ES-116S to
a power source.
4 LEDs
The LEDs are located on the top panel.
The following table describes the LEDs.
LED Status Description
PWR OnThe ES-116Sis on and receiving power.
Off The ES-116S is not receiving power.
4
ENGLISH
5 Wall Mounting (optional)
See the product specifications for the size of screws to
use and how far apart to place them.
1Locate a high position on wall that is free of
obstructions. Use a sturdy wall.
2Drill two holes for the screws. Make sure the distance
between the centers of the holes matches what is
listed in the product specifications appendix.
"Be careful to avoid damaging pipes or
cables located inside the wall when drilling
holes for the screws.
3Do not screw the screws all the way into the wall.
Leave a small gap of about 0.5 cm between the heads
of the screws and the wall.
LINK/
ACT
On The port is connected to an Ethernet
network.
Blinking The port is receiving or transmitting data.
Off The port is not connected to an Ethernet
network.
LED Status Description
ENGLISH
5
4Make sure the screws are snugly fastened to the wall.
They need to hold the weight of the Prestige with the
connection cables.
5Align the holes on the back of the Prestige with the
screws on the wall. Hang the Prestige on the screws.
6 Product Specifications
The following table lists the specifications.
Ethernet Standard IEEE802.3 10BASE-T Ethernet
IEEE802.3u 100BASE-TX Fast Ethernet
ANSI/IEEE802.3 Auto-negotiation
IEEE802.3x Flow Control
Protocol CSMA/CD
Technology Store-and-Forward switching architecture
Supports broadcast storm control
Non-blocking Wire
Speed
3.2 Gbps
Transfer Rate Ethernet: 10Mbps (half duplex), 20Mbps (full
duplex)
Fast Ethernet: 100 Mbps (half duplex),
200Mbps (full duplex)
Data Forwarding
Rate
14880 pps for 10Base-T (Ethernet)
148800 pps for 100Base-T (Fast Ethernet)
Connector RJ-45; Auto-MDIX on all ports
MAC Address 8K MAC address table
6
ENGLISH
Certifications
Federal Communications Commission (FCC)
Interference Statement
This device complies with Part 15 of FCC rules. Operation
is subject to the following two conditions:
• This device may not cause harmful interference.
• This device must accept any interference received,
including interference that may cause undesired opera-
tions.
Memory Buffer 160 KB
Network Cable 10BASE-T: 100Ω2-pair UTP/STP Cat. 3, 4, 5
100BASE-TX: 100Ω2-pair UTP/STP Cat. 5
Power Supply External; 12 V, 1 A (100 - 240 V, 50 - 60 Hz)
Temperature Operating: 0ºC ~ 45ºC (32ºF ~ 122ºF)
Humidity Operating: 10% ~ 90% (Non-condensing)
Dimensions 293 (L) x 101.5 (W) x 33.7 (H) mm
Screw Size M3.5 * 15 mm (for wall mounting)
(not provided)
Distance Between
Holes
200 mm (center-to-center)
EMI & Safety FCC Class A, CE, C-Tick
ENGLISH
7
FCC Warning
This device has been tested and found to comply with the
limits for a Class A digital switch, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
commercial environment. This device generates, uses,
and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this device in a residential
area is likely to cause harmful interference in which case
the user will be required to correct the interference at his
own expense.
CE Mark Warning
This is a class A product. In a domestic environment this
product may cause radio interference in which case the
user may be required to take adequate measures.
Notices
Changes or modifications not expressly approved by the
party responsible for compliance could void the user's
authority to operate the equipment.
This Class A digital apparatus complies with Canadian
ICES-003.
8
ENGLISH
Cet appareil numérique de la classe A est conforme à la
norme NMB-003 du Canada.
Taiwanese BSMI (Bureau of Standards, Metrology
and Inspection) A Warning:
Viewing Certifications
Refer to the product page at www.zyxel.com.
Safety Warnings
"For your safety, be sure to read and follow
all warning notices and instructions.
• Do NOT use this product near water, for example, in a
wet basement or near a swimming pool.
• Do NOT expose your device to dampness, dust or cor-
rosive liquids.
ENGLISH
9
• Do NOT store things on the device.
• Do NOT install, use, or service this device during a thun-
derstorm. There is a remote risk of electric shock from
lightning.
• Connect ONLY suitable accessories to the device.
• Do NOT open the device or unit. Opening or removing
covers can expose you to dangerous high voltage points
or other risks. ONLY qualified service personnel should
service or disassemble this device. Please contact your
vendor for further information.
• Make sure to connect the cables to the correct ports.
• Place connecting cables carefully so that no one will
step on them or stumble over them.
• Always disconnect all cables from this device before
servicing or disassembling.
• Use ONLY an appropriate power adaptor or cord for
your device.
• Connect the power adaptor or cord to the right supply
voltage (for example, 110V AC in North America or
230V AC in Europe).
• Do NOT allow anything to rest on the power adaptor or
cord and do NOT place the product where anyone can
walk on the power adaptor or cord.
• Do NOT use the device if the power adaptor or cord is
damaged as it might cause electrocution.
• If the power adaptor or cord is damaged, remove it from
the power outlet.
Table des matières
Langues :
Autres manuels ZyXEL Communications Changer
ZyXEL Communications
ZyXEL Communications Dimension ES-3024 Guide de référence
ZyXEL Communications
ZyXEL Communications XGS-4728F Manuel utilisateur
ZyXEL Communications
ZyXEL Communications ES-108E Manuel utilisateur
ZyXEL Communications
ZyXEL Communications XS3800-28 Manuel utilisateur
ZyXEL Communications
ZyXEL Communications EXTRASMART ES-1528 Manuel
ZyXEL Communications
ZyXEL Communications GS-1548 Manuel utilisateur
ZyXEL Communications
ZyXEL Communications IES-5000 Series Manuel utilisateur
ZyXEL Communications
ZyXEL Communications ES-105E Manuel utilisateur
ZyXEL Communications
ZyXEL Communications MES3500 Series Manuel utilisateur
ZyXEL Communications
ZyXEL Communications GS1920v2 Series Manuel utilisateur
ZyXEL Communications
ZyXEL Communications GS-1124A Manuel utilisateur
ZyXEL Communications
ZyXEL Communications NWA-3160 Manuel utilisateur
ZyXEL Communications
ZyXEL Communications EM-422/EM-412 Manuel utilisateur
ZyXEL Communications
ZyXEL Communications ExtraSmart ES-1552 Manuel utilisateur
ZyXEL Communications
ZyXEL Communications XGS4700 - FICHE TECHNIQUE Manuel utilisateur
ZyXEL Communications
ZyXEL Communications LAN SWITCHES - QUICK SALES GUIDE Manuel de l'opérateur
ZyXEL Communications
ZyXEL Communications GS-105B Manuel utilisateur
ZyXEL Communications
ZyXEL Communications SHD2110 Manuel utilisateur
ZyXEL Communications
ZyXEL Communications GS1200 SERIES Manuel utilisateur
ZyXEL Communications
ZyXEL Communications ES-2024PWR Mode d’emploi
