ZUBI 200 Mode d’emploi
MODEL 200 KNIFE GATE
VALVES
INSTALLATION & MAINTENANCE
MANUAL
Installation & maintenance manual
Knife gate valves Page 2
R
ev.
1
–
03/2019
Index
1. List of components / General arrangement
2. Description
3. Handling
4. Installation
5. Actuators / Operation
6. Maintenance
a. Changing the packing
b. Replacing the seat
c. Maintenance of the pneumatic cylinders
7. Recommendations
8. Storage
Installation & maintenance manual
Knife gate valves Page 3
R
ev.
1
–
03/2019
1. List of components / General arrangement
Installation & maintenance manual
Knife gate valves Page 4
R
ev.
1
–
03/2019
2. Description
The model 200 knife gate valve is unidirectional or bidirectional depending on the type of
closure that has been chosen commonly used for fluids with suspended solids.
The Model 200 complies with the following European directives:
2006/42/CE (Machinery Directive)
2014/68/EU (PED)
3. Handling
It is important to pay attention to the following points when handling the valve.
Do not lift the valve by the actuator or by the guards as they are not designed for it, you should
use eyebolts threaded into threaded holes in the body. It is also not advised to hold the valve
through the bore of the valve as this could damage or dislodge the seat.
It is advisable to use slings for lifting and handling valves where the weight exceeds that stated
as acceptable in the Health & Safety Manual Handling Codes.
Installation & maintenance manual
Knife gate valves Page 5
R
ev.
1
–
03/2019
4. Installation
For proper installation of the Model 200 valves it is important to consider the following:
Personnel handling and installing the valves must be trained and must comply with all
necessary safety regulations.
Prior to installation of the valve is important to inspect and verify that it has not suffered any
damage or harm during shipping and/or storage.
Make sure that the internal bore of the valve is clean and free from debris, also that the
adjoining areas where it will be installed are free from dirt, weld deposits and that the flange
facings are clean – suitable gaskets are too used.
The distance between the connection flanges must be correctly aligned and parallel as any
defects will cause difficulties in the operation. Special care should be taken to maintain the
correct distance between the flanges and to ensure that they are parallel to the valve body.
Incorrect alignment of the valve can cause deformations, which can lead to difficulties in
operation.
Tighten bolts with caution, so that tensions in the body do not cause any cracking or breaking.
No tilting, steady crosswise tightening. Bolts torques are to be observed.
At the time of installation, especially if valve is chosen unidirectional the valve must be
mounted so that the higher pressure pushes the gate against the seat as shown in the image.
Despite the valve being unidirectional it can also be used in the ´off seat´ direction of the flow
where the valve will work with pressures up to 1/3 of the recommended pressure against seat.
*Note that the direction of fluid need not always be equal to the direction of pressure.
Installation & maintenance manual
Knife gate valves Page 6
R
ev.
1
–
03/2019
As a general rule, the valve should be installed vertically on horizontal pipe whenever possible.
However it is also possible to mount it in any other position as long as you consider that any
actuators fitted to the valve are adequately supported when the position is horizontal or
inclined.
Once the valve has been installed and securing the flanges are tight, operate the valve under
pressure and check the seal under load. It is important to note that during transportation or
storage of the valve the gland material might have settled so that in the event of leak, tighten
the gland nuts gradually and in a crosswise pattern. Only tighten just enough to prevent any
leakage, if the gland is overtighten, as this reduces the life of the gland and increase the force
required to operate the valve, possibly causing damage.
5. Actuators / Operation
Hand Wheel
To open the valve turn the hand wheel counterclockwise, to shut valve turn the hand wheel
clockwise.
Lever
To operate the valve first loosen the quick release locking screw and then operate the lever in
the direction of opening or closing. To secure the position tighten the quick release locking
lever.
Cylinder
For pneumatically operated valves, there are option for double-acting and single-acting, in
both cases the recommended air pressure is 5 to 6 bar.
We recommend that the compressed air is dry, filtered and lubricated for proper operation
and longevity of the cylinder.
Hydraulic
Where valves are operated with hydraulic cylinders is important to use clean hydraulic and to
maintain the cylinders on a regular basis. It is recommended specifying low temperature oils in
areas where the valves are constantly exposed to cold temperatures.
Gear-box
The operation with a gearbox is similar to the drive wheel. For best performance it is
recommended to lubricate the gear every six months. Where valves are in storage it is
recommended to operate every 4 months.
Electric
Recommended electric actuator rpm for Zubi T200 valve is 45rpm, higher speed rpm under
end user responsibility.
Installation & maintenance manual
Knife gate valves Page 7
R
ev.
1
–
03/2019
6. Maintenance
In general the valves only require maintenance for changing the packing and changing the
seats on both the unidirectional and bidirectional valves when leakage is detected across the
valve when fully closed. To maintain easy operation it is recommended that the threaded valve
stem be cleaned and greased through the bronze drive bush housed in the bridge.
a) Changing the packing
It is important to change the packing, either on a regular basis (depending on the number of
operations and on the circulating fluid) or due to the deterioration thereof. The packing
change must be made as follows:
* We should note that this process will release the valve drive so it would be interesting using
a crane if deemed necessary.
1. Next, loosen the lower bolts to the support plate.
2. Undo the bolts holding the gate to the stem and remove the operator.
3. Then, loosen the nuts holding the gland follower to remove that part.
Installation & maintenance manual
Knife gate valves Page 8
R
ev.
1
–
03/2019
4. Remove old packing, clean out packing box and replace with new gland.
5. Replace the gland follower tightening the nuts in a crosswise pattern. Do not
overtighten.
6. Replaced the stem connecting bolts and the support plate bolts.
7. Operate the valve several times to check the possible leaks. Adjust gland as previously
instructed if leaks appear.
b) Replacing the seat
The seats are in place only in valves where leak tight closure is required or on bidirectional
type. It is important to make changes either for regular maintenance (depending on the
number of operations and the state of the circulating fluid) or due to the detection of leakage
across the valve. The seat must be changed as follows:
1. Remove the valve from the pipeline, making sure the line is not under pressure before
removing.
2. Fully open the valve
3. With a drift remove the seat retaining ring. Remove the old seat and clean the body of
debris.
4. After replacing the seat is replaced making sure the join is in the upper body. It is
recommended to apply some grease to the seat to ease into the body and to keep in
place.
Installation & maintenance manual
Knife gate valves Page 9
R
ev.
1
–
03/2019
5. With care replace the seat retaining ring, tapping with a drift all round the edge until
ring is back in place
6. Close the valve tightly against the seat, checking contact between gate and seat.
7. Operate several times to assist alignment and to check for possible leaks
*To replace a Teflon (PTFE) seat it is recommended to preheat at 50º to soften and ease of
replacement.
c) Maintenance of pneumatic cylinders
The actuators seals must be replaced if leaking is detected between the two cylinder
chambers. This leak is due to the deterioration of the seals or cylinder liner.
Complete replacement of the cylinder must be made as follows:
1. Disconnect the cylinder from the air supply with the valve in the closed position; make
sure all the air is drained out of the cylinder.
2. Loosen and remove the lower bolts on the support plates.
3. Disconnect the shaft from the gate.
4. Next, install the new drive, reconnecting the shaft to the gate.
5. Replace the support plates and tighten the bolts.
6. Operate the valve several times before placing back in line, pressurise with air not
exceeding 7 bar or less than 5, thus proving the proper functioning of the cylinder.
Installation & maintenance manual
Knife gate valves Page 10
R
ev.
1
–
03/2019
When replacing the cylinder components, you must follow the guidelines above as 1-2-3 then
as follows:
To renew the o-rings on the covers, undo the tie rod nuts; carefully remove cover
tapping gently upwards trying not to damage the barrel or cap. Remove old o-ring
clean cap, insert new o-ring and replace cap. Tighten the nuts on the tie rods
diagonally.
To replace the piston remove the upper cover and the cylinder barrel leaving the
piston exposed inside. Subsequently undo the nyloc nut and washer holding the piston
to the piston rod, removed the damaged piston, clean thread and replace with new
piston washer and new nyloc nut.
To replace the seal cap, bottom cover came loose and scraper, leaving open the
damaged board.
Table des matières
Autres manuels ZUBI Unité de contrôle
Manuels Unité de contrôle populaires d'autres marques
Festo
Festo Compact Performance CP-FB6-E Manuel de la liste des pièces
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur
JS Automation
JS Automation MPC3034A Manuel utilisateur
JAUDT
JAUDT SW GII 6406 Series Guide rapide
Spektrum
Spektrum Air Module System Manuel utilisateur
BOC Edwards
BOC Edwards Q Series Manuel utilisateur
