Zte MF28B Manuel utilisateur

Inserting SIM Card

Open the protective cover of the SIM port shown below and insert the

SIM card.

Note: Please power off the MF28B router and remove the external

power adapter before removing or inserting the SIM card. If not, the

router or SIM card may be damaged.

Switching On Your Device

1. Turn the Power Switch on to get started.

Note: Do not put anything on the top of the router. Do not lay

routers overlapping each other when using.

2. Wait 2~3 minutes after turning the MF28B router on before you

use the service.

Note: If the Mobile Network indication LED (left most indicator)

is blinking constantly, try to move the router to another location.

The router takes 1~2 minutes to initialize, connect to the network

and obtain an IP address.

Power Switch

Appearance

SIM Port

LED Indicators

WPS ButtonUSB Port

Interface

Indicator Description

SIM Port Where the SIM card is inserted.

LED Indicators To indicate the status of the device.

USB Port To connect with an external storage device or

USB shared printer.

Interface

Contains RJ45 interfaces (LAN1/WAN, and

LAN2 ~ LAN4), power switch, reset switch,

and power socket.

WPS Button To activate Wi-Fi Protected Setup

authentication process.

Interface Description

1 LAN1/WAN For Ethernet connections or ADSL/cable

modem connection.

2 LAN2~LAN4 For Ethernet connections.

3 ON/OFF To turn the router ON or OFF.

4 Reset Switch To restore the router to the factory default

settings by holding for 7 seconds.

5 Power Socket To connect to the external power supply.

LED Indicator

Indicator State Description

1 Mobile Network

Blue Registered to LTE network

Green Registered to 4G network

OFF Not Registered

2 Mobile Network

connection

status

Always ON Mobile network connection

established

Blinking Mobile network connection is

establishing

OFF Mobile network connection not

established

3 Mobile Network

signal strength

Always ON Signal strength is very good or

good

Blinking Signal strength is weak

OFF No signal

4 Error Blinking

No SIM card inserted, PIN

enabled without entering correct

PIN code on Web UI

5 Wi-Fi

Always ON Wi-Fi connection established

Blinking Wi-Fi data transmission

OFF Wi-Fi is shut down

6 Power Always ON

Green--Once device initialized

and ready

Red-- Device is initializing

OFF Device is powered off

Connecting to the internet via Wi-Fi

1. Power on your device. It will take 2~3 minutes to initialize.

2. Scan for available wireless networks using the normal Wi-Fi

application of your Wi-Fi device.

3. Select the SSID of your MF28B router, and connect to it (The

default SSID and Wi-Fi password can be found on the label

found on the MF28B router box). Wait approximately 30 seconds

for the connection to establish.

Note: You can modify the SSID and password using the Web

GUI advanced conguration page.

Connecting to the internet via Ethernet Cable (RJ45)

1. Power on your device. It will take 2~3 minutes to initialize.

2. Connect the supplied Ethernet cable to a LAN port at the back of

the MF28B router.

3. Connect the other end of the Ethernet cable to your computer

and wait approximately 45 seconds for the connection to

establish.

Logging into the WebGUI (for optional device

conguration)

1. Establish a connection between the MF28B router and Wi-Fi

device.

2. Launch your web browser and enter the router address (Default

address: http://192.168.1.1).

Note: It is recommended that you use one of the following web

browsers: Internet Explorer (7.0 or later), Firefox (3.0 or later),

Opera (10.0 or later), Safari (4.0 or later) or Chrome (10.0 or

later).

3. When the login page appears as follows, input the password (The

default password is admin).

Please refer to your MF28B User Manual for conguration options

and instructions.

Autres manuels pour MF28B

Table des matières

Autres manuels Zte Routeur réseau

Zte

Zte GPON ONT ZXHN F600 Manuel utilisateur

Zte

Zte T3000 Manuel utilisateur

Zte

Zte MF286D Manuel utilisateur

Zte

Zte MF65 Manuel utilisateur

Zte

Zte MF283+ Manuel utilisateur

Zte

Zte E1200 Manuel utilisateur

Zte

Zte Mobile Wi-Fi R209-Zr Manuel utilisateur

Zte

Zte ZXR10 M6000 Series Manuel utilisateur

Zte

Zte MF288 Manuel utilisateur

Zte

Zte MF286 Manuel utilisateur

Zte

Zte MC801A1 5G Manuel utilisateur

Zte

Zte ZXR10 3800-8 Instructions d'installation

Zte

Zte ZXHNF660 Manuel utilisateur

Zte

Zte ZXHN H168M Manuel utilisateur

Zte

Zte MF29A Manuel utilisateur

Zte

Zte MF286R Manuel utilisateur

Zte

Zte MF286D Manuel utilisateur

Zte

Zte ZXR10 5900E Series Manuel utilisateur

Zte

Zte ZXR10 2900E Series Manuel d'installation

Zte

Zte MF25A Manuel utilisateur

Zte

Zte MF60 Manuel utilisateur

Zte

Zte ZXHN H108L Manuel utilisateur

Zte

Zte MF279T Manuel utilisateur

Zte

Zte ZXR10 3800-8 Instructions d'installation

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité