ZORA P1 Manuel utilisateur
1
Zora P1 DEVELOPMENT BOARD
Zora P1 V1.0
電波法により5GHz帯は屋内使用に限ります
2
目录
Orbbec Pi 2（A311D）Development board help document.......................................................1
1. Orbbec Pi P2（A311D-4G-01 ）Introduction of Development Board Interface............. 3
1.1 Front picture of development board................................................................................ 3
1.2 Back picture of development board................................................................................. 3
1.3 Introduction to hardware interface............................................................................. 3
1.4 42Pin GPIO introduction (form 01 to 42)....................................................................5
1.5 Uart introduction（from 01 to 04）........................................................................... 5
1.6 PMD introduction（from 01 to 04）.......................................................................... 5
1.7 RTC introduction............................................................................................................5
2. Preparation for firmware burning............................................................................................7
2.1 Long press “update” button enter burn mode................................................................ 7
2.2 Use hardware interface uart-debug enter burning mode:.............................................9
2.3 Use ADB tool to enter burning mode.............................................................................10
3. Detailed method and operation steps of disassembling and burning firmware............. 11
3.1 Configuration requirements for computers：............................................................... 11
3.2 Using the update button to burn the firmware............................................................. 11
3.4 Use hardware interface uart-debug enter burning mode........................................... 16
3.5 Burn firmware with ADB tool........................................................................................... 17
3.6 Burn the firmware to multiple development boards at the same time...................... 19
3.7 Download burning tools...................................................................................................19
5. Set ADB debugging................................................................................................................ 20
6. EMMC extension module instructions.................................................................................. 20
7. POE Module introduction.......................................................................................................21
8. NPU help.................................................................................................................................. 23
9. Hardware data of development board................................................................................. 24
10. Firmware Download............................................................................................................26
11. Accessories around development board..........................................................................27
3
1. Zora P1（A311D-4G-01 ）Introduction of Development Board Interface
1.1 Front picture of development board
1.2 Back picture of development board
1.3 Introduction to hardware interface
processor
Amlogic, Quad A73+ Dual A53
4
RAM
2GB DDR4*2
storage
32GB EMMC
EMMC extension
Pluggable EMMC module(8GB,16GB,32GB)
Storage-Micro SD
Up to 128Gb
MIPI-CSI
1 CSI + 8M HDR ISP
MIPI-DSI
Support
USB
2xUSB 3.0 + 2xUSB 2.0 + 1USB XHCI OTG 2.0
HDMI
HDMI 2.1
Wifi/BT
WIFI 2.4/5G 802.11a/b/g/n/ac, 2x2 MIMO，BT5.0
10m
Ethernet
RJ45 GigE Vision
POE
Pin + Extra Cap
Microphone
On-board
PDM
PDM interface microphone
Debug
Micro USB
Buttons
Power ,Reset,ADC ,Update and act
OPEX Wifi
LED
Power status indicator
42Pin GPIO
Detail in 42Pin GPIO introduction
UART
1
I2C
2
SPI
2
I2S
1
PWM
2
ADC
1
DC-OUT
1x5V+1x3.3V
GPIO
8
Ground
8
PMU
YK613
DC-IN
12V 2.1mm
OS
Android 9，Ubuntu 18.04，Linux 4.9
Replace firmware
By replacing the EMMC module
Upgrade mode
USB update，
5
1.4 42Pin GPIO introduction (form 01 to 42)
TX（01）
RX
GND
S_M0
S_M1
S_CS
S_CK
GND
I_MCK
I_SCK
I_LR
I_DO
GND
GPIO1
GPIO2
GPIO3
GPIO4
GND
PWM2
5V
5V
SDA
SCL
SDA2
SCL2
GND
P_D1
P_D0
P_SY
P_CK
GND
GCLK
32K
GND
GPIO5
GPIO6
GPIO7
GPIO8
GND
PWM1
3.3V
3.3V（42）
1.5 Uart introduction（from 01 to 04）
3.3V（01）
RX
TX
GND（04）
1.6 PMD introduction（from 01 to 04）
3.3v
（01）3.3v GND PDM_DCK GND PDM_DIN0 PDM_DIN1 GND
（07）
1.7 RTC introduction
GND（01）VBAT（02）
6
1.8 Product size description
116*100mm
7
2. Preparation for firmware burning
There are three ways to enter burn mode:
2.1 Long press “update” button enter burn mode
a．Long press update button
8
b.Connect the OTG interface of development board through windows(win 10 or win7)
system computer
9
c.Link power 12V-2A adapter through DC-in interface
d.Successfully linked the burning software。
2.2 Use hardware interface uart-debug enter burning mode:
a. Using USB to UART serial port tool connect the UART-debug interface
b. Through serial protocol tool software ,type in “reboot”
c. When the development board is restarted， Press enter continuously and ente
uboot mode
d.type in “update”
e. Successfully linked the burning software
10
2.3 Use ADB tool to enter burning mode
a. Power on the development board by connecting the power adapter
b. Open the computer CMD console
c. Connecting computer and development board with the otg interface
d.CMD console type in “adb reboot update “
e. Successfully linked the burning software
Table des matières
Manuels Carte mère populaires d'autres marques
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manuel utilisateur
Gigabyte
Gigabyte GA-9IVDT Manuel utilisateur
Texas Instruments
Texas Instruments ADS8372EVM Manuel utilisateur
Commell
Commell MS-C73 Manuel utilisateur
IBT Technologies
IBT Technologies MB860 Manuel utilisateur
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur
