ZKTeco Mars-B1011 Manuel utilisateur

Installation Guide

Mars-B1000 Series

Due to regular upgrades of systems and products, ZKTeco could not guarantee exact consistency between the

actual product and the written information in this manual.

Version: 1.0

Applicable Models: Mars-B1000/1011/1022/1200/1211/1222

1 Installation Requirements

The installation position of the swing barrier turnstile depends on its size. A distance of 100mm between

the swing barrier turnstile and the wall needs to be reserved for ease of opening the top cover of the

machine to perform maintenance and adjustment. The reference ﬁgure is shown below:

2 Installation Position

It is recommended that the swing barrier turnstile must be installed on a horizontal solid platform

with a height of 50mm to 100mm.

After installation, check if the connection is done correctly at the connecting points of the ground

wire, at the connector assemblies and wiring points of the circuits, as well as at each movable part

of the swing barrier turnstile. Any loose nuts, screws and other fasteners should be tightened in

time to avoid any failures caused by long-time operations.

3. Make sure the ground wire of the system is reliably connected to avoid personal injuries or other

accidents.

2. It is also recommended that the swing barrier turnstile should not be used in the corrosive

environment.

3 Preparation

To install the Mars-B1000 Series you must have:

A Screwdriver: To remove or install the screw on the device.

A Pencil: To mark the device size and the screw hole.

A Electric Drill: To drill holes according to the marked screw holes.

A Wrench: To secure the M12 expansion screw on the device.

4 Installation

1. Place the turnstile to the installation site.

1010.00

1355.00

A Tapeline: To measure the dimensions that need to be measured during the installation of the device.

4 Installation

Remove the screws ﬁxing the top lid, and remove the top lid.

Remove the side lid that hang on the device.

②

①

Mark the ﬂoor following the periphery of the legs.

710.00

120.00 120.00

1253.00

Take the turnstile aside and use the electric drill according to the drawn screw holes.

6. Clean up the soil and dust after the drilling is completed, place the turnstile to the installation site

again.

Insert the M12 expansion screw and tighten it with a wrench.

8. Connect the online cables and perform the power-on test. If the test is OK, install the side lid and

top lid of the device.

9. It is recommended that a warning line be marked on the ground after installing the device, so as to

prompt the pedestrian to stand behind the warning line when veriﬁcation.

100.00

180.00

1010.00

180.00

650.00

300.00 300.00

238.50

1010.00

50.00

600.00

M12Expansion

Screw Tether Cable Power Line

10. If you need to assemble the swing arm by yourself, please refer to the diagram below for

installation.

Note: The swing arm is already installed in the factory.

①

②

ZKTeco Industrial Park, No. 32, Industrial Road,

Tangxia Town, Dongguan, China.

Phone : +86 769 - 82109991

Fax : +86 755 - 89602394

www.zkteco.com

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ZKTeco Tourniquet

ZKTeco

ZKTeco TS1000 Pro Series Manuel utilisateur

ZKTeco

ZKTeco TS1000 Series Manuel utilisateur

ZKTeco

ZKTeco Mars-F1000 Manuel utilisateur

ZKTeco

ZKTeco SBT2000S Manuel utilisateur

ZKTeco

ZKTeco SBTL8000 Series Manuel utilisateur

ZKTeco

ZKTeco SBT2000S Manuel utilisateur

ZKTeco

ZKTeco mTS1000 Series Manuel utilisateur

ZKTeco

ZKTeco Mars-S1011 Manuel utilisateur

ZKTeco

ZKTeco SBT1000S Manuel utilisateur

ZKTeco

ZKTeco Mars Pro-S1000 Manuel utilisateur

ZKTeco

ZKTeco FHT2300 Manuel utilisateur

ZKTeco

ZKTeco FHT2300 Manuel utilisateur

ZKTeco

ZKTeco TS5000A Series Manuel utilisateur

ZKTeco

ZKTeco Mars-S1000 Manuel utilisateur

ZKTeco

ZKTeco TS3000 Series Manuel utilisateur

ZKTeco

ZKTeco SBT1000S Manuel utilisateur

ZKTeco

ZKTeco TS1000 Pro Series Manuel utilisateur

ZKTeco

ZKTeco Mars-F1000 Manuel utilisateur

ZKTeco

ZKTeco Mars-B1000 Manuel utilisateur

ZKTeco

ZKTeco SBTL9000 Series Manuel utilisateur

ZKTeco

ZKTeco TS1000 Pro Series Manuel utilisateur

ZKTeco

ZKTeco TS1000D Manuel utilisateur

ZKTeco

ZKTeco SBTL7000 Series Manuel utilisateur

ZKTeco

ZKTeco TS5000A Series Manuel utilisateur

Manuels Tourniquet populaires d'autres marques

Oxgard

Oxgard CUBE C-10 Manuel utilisateur

LBA GROUP

LBA GROUP LBAT10 Manuel utilisateur

Magnetic

Magnetic mTripod Manuel utilisateur

Kaba

Kaba Argus HSG-E02 Manuel utilisateur

Automatic Systems

Automatic Systems TR491 Manuel utilisateur

Turnstiles

Turnstiles HZ-SWGS01 Manuel utilisateur

DSI

DSI DST-80 Manuel utilisateur

OZAK

OZAK VP-125 Manuel

Automatic Systems

Automatic Systems SMARTLANE SL 90X Manuel utilisateur

Alvarado

Alvarado MT Instructions d'installation et d'utilisation

JKDC SECURITY

JKDC SECURITY JKDC-100C Manuel utilisateur

Alvarado

Alvarado SU5000 Manuel utilisateur

Magnetic Autocontrol

Magnetic Autocontrol MPT 33 Manuel utilisateur

Oxgard

Oxgard Praktika T-04K Guide de démarrage rapide

digicon

digicon CATRAX Plus Manuel utilisateur

Oxgard

Oxgard CUBE C-04-s Manuel utilisateur

BOON EDAM

BOON EDAM Turnlock 100 Mode d’emploi

Wano

Wano Tripod BO-DSN10 Manuel utilisateur