ZKTeco SBT2000S Manuel utilisateur

Installation Guide

SBT2000S Swing Barrier Turnstile

Version: 1.0

Due to regular upgrades of systems and products, ZKTeco could not guarantee exact consistency between the

actual product and the written information in this manual.

It is recommended that the swing barrier turnstile be installed on a horizontal solid platform with

50 mm to 100 mm in height, the horizontal angle must not be greater than ±0.7°.

After installation, check if the connection is done correctly at the connecting points of the ground

wire, at the connector assemblies and wiring points of the circuits, as well as at each movable part

of the swing barrier turnstile. Any loose nuts, screws and other fasteners should be tightened in

time to avoid any failures caused by long-time operations.

1 Installation Requirements

The installation position of the swing barrier turnstile depends on its size. A distance of 100mm between

the swing barrier turnstile and the wall needs to be reserved for ease of opening the top cover of the

machine to perform maintenance and adjustment. The reference ﬁgure is shown below:

2 Installation Position

Figure 2-1 SBT2000S Series Dual-lane

Make sure the ground wire of the system is reliably connected to avoid personal injuries or other

accidents.

It is also recommended that the swing barrier turnstile should not be used in the corrosive

environment.

2274.02

2174.02

900

592

800

3 Preparation

Below is the outline and dimensions of SBT2000S:

Figure 3-1

Tools: A measuring tape, an adjustable wrench, an impact drill and a small screwdriver (included in

the package).

The power and signal wires should be set separately to easily distinguish strong and weak power.

Please invite professional personnel to complete the wiring. The device must be connected to the

ground.

Thread the connection wire of the device through the tube before assembly.

Material: A PVC anti-ﬁre and insulation tube (diameter≥25mm), standard three-core power

extension wire, tether cable (random conﬁguration), M12 expansion screws (included in the

package).

202

187

531 814

1109

592

800

4 Installation

Prepare the tools for product installation and sort out the auxiliaries according to the packing list.

Mark the screw hole at the centre of the stand, and the edge of the chassis base on the ground

according to the sizes as shown on the Figure 4-1.

Drill the holes with Ф14 and embed M12 anchor screws or expansion screws. As shown on the

Figure 4-2.

Figure 4-2

Figure 4-1

1. Drill hole 2. Implantation of

the screw

3. Fix screw

SBT2000S

148

M12Concrete

Anchor

Power Line φ25mm PVC pipe

1019.15

1225.00

120.50

2274.02

2174.02

900

800

592

4. Place the swing barrier turnstile according to the sizes and positions as shown in the ﬁgure before

installation and ﬁxing.

For the outlets of the concealed cables, please refer the below diagram indicating the mounting

holes. The input voltage for this swing barrier turnstile is AC100V-120V/200V-240V and its master

and slave are connected by an 2-core cable (signal) and a 2-core cable (power). When installing the

swing barrier turnstile, the user only needs to connect it to the corresponding ports. Note that the

PVC conduits are laid 100mm under the ground, with the height of the exposed part not exceeding

100mm. In addition, the conduit outlet is bent back to prevent the ingress of water into the conduit.

SBT2000S series installation holes and cabling positions is shown in Figure 4-3:

Air Switch

Figure 4-3

WarningLine

Figure 4-4

6. Connect the online cables and perform the power-on test. Wait for 10 seconds for the turnstile to

complete the self-test program. At the same time, check if the indicators work properly. If

everything works ﬁne, you can tighten the screws and ﬁx the device. If an exception occurs, please

contact your vendor.

7. It is recommended that a warning line be marked on the ground after installing the device, so as to

prompt the pedestrian to stand behind the warning line when swiping the card. As shown in Figure

4-4:

5 Wiring Diagram

Below is the wiring diagram:

Autres manuels pour SBT2000S

Table des matières

Autres manuels ZKTeco Tourniquet

ZKTeco

ZKTeco SBTL9000 Series Manuel utilisateur

ZKTeco

ZKTeco TS2000 Pro Series Manuel utilisateur

ZKTeco

ZKTeco Mars-B1011 Manuel utilisateur

ZKTeco

ZKTeco SBTL7000 Series Manuel utilisateur

ZKTeco

ZKTeco TS1000 Pro Series Manuel utilisateur

ZKTeco

ZKTeco TS1000 Pro Series Manuel utilisateur

ZKTeco

ZKTeco FHT2300 Manuel utilisateur

ZKTeco

ZKTeco Mars-S1011 Manuel utilisateur

ZKTeco

ZKTeco FHT2300 Manuel utilisateur

ZKTeco

ZKTeco Mars-F1000 Manuel utilisateur

ZKTeco

ZKTeco Mars-S1000 Manuel utilisateur

ZKTeco

ZKTeco TS1000 Series Manuel utilisateur

ZKTeco

ZKTeco Mars-B1000 Manuel utilisateur

ZKTeco

ZKTeco TS2000 Series Manuel utilisateur

ZKTeco

ZKTeco SBTL8000 Series Manuel utilisateur

ZKTeco

ZKTeco TS1000 Pro Series Manuel utilisateur

ZKTeco

ZKTeco mTS1000 Series Manuel utilisateur

ZKTeco

ZKTeco FBL6000 Pro Series Manuel utilisateur

ZKTeco

ZKTeco Mars Pro-S1000 Manuel utilisateur

ZKTeco

ZKTeco FBL6000 Pro Series Manuel utilisateur

ZKTeco

ZKTeco TS1200 Series Manuel utilisateur

ZKTeco

ZKTeco SBT1000S Manuel utilisateur

ZKTeco

ZKTeco TS3000 Series Manuel utilisateur

ZKTeco

ZKTeco Mars-F1000 Manuel utilisateur

Manuels Tourniquet populaires d'autres marques

Oxgard

Oxgard CUBE C-10 Manuel utilisateur

LBA GROUP

LBA GROUP LBAT10 Manuel utilisateur

Magnetic

Magnetic mTripod Manuel utilisateur

Kaba

Kaba Argus HSG-E02 Manuel utilisateur

Automatic Systems

Automatic Systems TR491 Manuel utilisateur

Turnstiles

Turnstiles HZ-SWGS01 Manuel utilisateur

DSI

DSI DST-80 Manuel utilisateur

OZAK

OZAK VP-125 Manuel

Automatic Systems

Automatic Systems SMARTLANE SL 90X Manuel utilisateur

Alvarado

Alvarado MT Instructions d'installation et d'utilisation

JKDC SECURITY

JKDC SECURITY JKDC-100C Manuel utilisateur

Alvarado

Alvarado SU5000 Manuel utilisateur

Magnetic Autocontrol

Magnetic Autocontrol MPT 33 Manuel utilisateur

Oxgard

Oxgard Praktika T-04K Guide de démarrage rapide

digicon

digicon CATRAX Plus Manuel utilisateur

Oxgard

Oxgard CUBE C-04-s Manuel utilisateur

BOON EDAM

BOON EDAM Turnlock 100 Mode d’emploi

Wano

Wano Tripod BO-DSN10 Manuel utilisateur