ZKTeco TL600 Manuel utilisateur

Installation GuideVersion: 2.0

Important NotesTable of ContentsPlease read this Installation Guide carefully and contact the Customer Care Service if you have any questions about the installation.To avoid any future service charges that can arise as a result of incorrect installation, it is recommended that installation can be performed by a professional technician prevent any potential service charges that can occur due to incorrect installation.We regularly revise the contents of this Installation Guide and update our products to enhance quality and performance without prior notice.1.2.3.You must perform the initialization process on each installation immediately after installing this lock on any door, as described in the initialization procedure on page 8.4.Do not install the batteries until the lock is installed.5.What's in the Box.............................................................................................................1Installation Diagram.......................................................................................................2Installation Procedure....................................................................................................21. Door Properties..........................................................................................................................................22. Drill Holes on the Door.............................................................................................................................4 3. Install Mortise and Cylinder ...................................................................................................................44. Install Spindle and Studs.........................................................................................................................55. Install the Outdoor Unit...........................................................................................................................56. Install Indoor Unit......................................................................................................................................67. Install Batteries and Cover......................................................................................................................78. Install Strike Plate and Box......................................................................................................................79. Physical Test.................................................................................................................................................8

1What's in the BoxDoor Thickness45 to 50 mm51 to 60 mmScrewNote:Spindles for door thickness from 45 to 60 mm are included in the standard package. To ensure proper lock operation, please use the speciﬁed spindle based on the thickness of your frame.Indoor UnitMortiseStrike Plate and BoxCylinderSpindle BKeysSpindle APlugScrew AScrew BScrew DScrew CMetal PinCardsScrew AScrew BSpindle CStudOutdoor Unit

Installation Diagram2Installation Procedure1Door PropertiesMeasure the Door ThicknessA.Measure the thickness of the door and select the appropriate Spindle length. For further details, please refer the table on Page 1.Check the Door Opening DirectionB.The position of the handle is determined by the opening direction of the door. Below is the graphical representation of the door opening direction in reference to your position outside the room.Outdoor UnitMetal PinKeysStudSpindle A/BStudCylinderScrew AScrew BStrike Plate and BoxMortiseDoorIndoor UnitBattery(not included)Screw CSpindle CMetal PinScrew DPlugBattery Cover

3Adjust the Direction of Latch (if needed)Push the reverse block in upward direction.Push the bolt of the latch into the mortise.1)2)MortiseStrikePlateMortiseMortiseStrikePlateMortiseStrikePlateStrikePlateUser LocationLeft InwardRight InwardLeft OutwardRight OutwardRotate the latch bolt to 180° inside the mortise, and release it.3)Change the Handle Direction (if needed)C.Remove the directional screw of the handle, rotate the handles of the outdoor and indoor units to 180 degrees in the left or right direction, depending on the door.1)Secure the handle again with the directional screw.2)

Place the installation template at the desired handle height.Mark the holes to be drilled and drill the marked locations.1)2)43Install Mortise and Cylinder Put the Mortise into the hole that was drilled, and secure the Mortise with Screw A. Insert the Cylinder into the Mortise (note the front sides and back sides) and secure it with Screw B.1)2)2Drill Holes on the DoorDesired handle height

Backset

Center line of handle

60mm

Screw AScrew B

54Install Spindle and StudsInsert the Spindle A/B into the clutch and insert the Metal Pin from the bottom of the clutch, force the pin apart and bend it to hold the Spindle A/B. Then, install the studs.1)2)Metal Pin5Install the Outdoor UnitPass the outdoor unit cable through the top of the cable hole.Pass the Spindle A through the hole of the clutch and the outdoor unit must be close to the entrance.1)2)StudRight Inward/OutwardLeft Inward/Outward

66Install Indoor UnitInsert the Metal pin on Spindle C.1)Connect the cable to the Indoor Unit port.2)Metal PinPlace the Indoor Unit appropriately on the Mounting Plate. Then use Screw C & Screw D to protect the Indoor Unit.3)Screw CScrew D

77Install Batteries and CoverMake sure that the Strike Box is aligned with the latch bolt. Then, use the installation template to drill the holes.1)Align the Strike Plate and Box with the holes drilled and protect them with Screw A.2)8Install Strike Plate and BoxInsert four Alkaline AA batteries and cover them with the battery cover, and insert the Plug.Screw A

89Physical TestTest the lock by rotating the handle and the double locking knob.A.The front handle can be rotated even when the door is closed, but the door remains unlocked.1)When the Security knob is turned on, the door remains unlocked even if the handle is rotated from indoor.2)Note:Test the lock by using the mechanical keyPress and rotate the cover of the key hole with your ﬁnger.1)Insert the Key into key hole and rotate 90°.2)PressNote: Please secure your keys for emergency purpose. If push handle downward, the lock close. It is installation problem, please refer to step 5 installation. 3)

Table des matières