ZiLOG S3F8S19 Manuel utilisateur

S3 Family of Microcontrollers

S3F8S19 Development

Kit

www.zilog.com

UM026803-0816

User Manual

UM026803-0816 Disclaimer

S3F8S19 Development Kit

User Manual

DO NOT USE THIS PRODUCT IN LIFE SUPPORT SYSTEMS.

LIFE SUPPORT POLICY

ZILOG’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE

SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF

THE PRESIDENT AND GENERAL COUNSEL OF ZILOG CORPORATION.

As used herein

Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b)

support or sustain life and whose failure to perform when properly used in accordance with instructions for

use provided in the labeling can be reasonably expected to result in a significant injury to the user. A criti-

cal component is any component in a life support device or system whose failure to perform can be reason-

ably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.

Document Disclaimer

or technology described is intended to suggest possible uses and may be superseded. ZILOG, INC. DOES

NOT ASSUME LIABILITY FOR OR PROVIDE A REPRESENTATION OF ACCURACY OF THE

INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED IN THIS DOCUMENT. ZILOG ALSO

DOES NOT ASSUME LIABILITY FOR INTELLECTUAL PROPERTY INFRINGEMENT RELATED

IN ANY MANNER TO USE OF INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED

HEREIN OR OTHERWISE. The information contained within this document has been verified according

to the general principles of electrical and mechanical engineering.

S3 and Z8 are trademarks or registered trademarks of Zilog, Inc. All other product or service names are the

property of their respective owners.

Warning:

UM026803-0816 Revision History

S3F8S19 Development Kit

User Manual

iii

Revision History

Each instance in this document’s revision history reflects a change from its previous edi-

tion. To learn more, refer to the corresponding page(s) or appropriate links furnished in the

table below.

Date

Revision

Level Description Page

Aug

2016

03 Updated for ZDS-S3 version 5.3.0. Removed ISP I support All

Jun

2015

02 Deleted Step 6 of Establish a Connection with the PC;

Deleted Appendices C, D, and E and changed references to online help top-

ics.

Sep

2014

01 Original issue. n/a

UM026803-0816 Overview

S3F8S19 Development Kit

User Manual

Overview

Zilog’s S3F8S19 Development Kit, part number S3F8S190100ZCOG, allows you to eval-

uate your S3F8S19-based designs and applications. The Kit features a Development

Board consisting of the following components:

•

Four LEDs

•

Five pushbuttons

•

Buzzer/speaker

•

LCD module

•

UART

This user manual provides instructions for setting up and configuring the S3F8S19 Devel-

opment Board. It includes schematic diagrams and a discussion of the Board features and

ZDS II.

The S3F8S19 Development Board features an S3F8S19 MCU in a 48-pin QFP package,

plus an S3 PGM connector to connect the Board to a host development PC using the S3

Flash In-System Programmer II (ISP). To learn more about the S3F8S19 MCU, refer to

the S3F8S19 Product Specification (PS0312) and/or the S3 Flash In-System Programmer

User Manual (UM0266).

This document guides you through the following tasks:

•

Downloading and installing ZDSII software and documentation

•

Connecting the S3 Flash ISP II and S3F8S19 Development Board to your PC

•

Starting the S3F8S19 Ledblink sample program

Kit Contents

The S3F8S19 Development Kit contains the following items:

•

S3F8S19 Development Board

•

S3 Flash ISP II

•

10-circuit ribbon cable

•

USB A (male) to Mini-B USB cable (2)

•

S3F8S19 Development Kit hardcopy insert

UM026803-0816 Features

S3F8S19 Development Kit

User Manual

Figure 1 shows the contents of the S3F8S19 Development Kit.

Features

The S3F8S19 Development Kit includes the following key items.

•

S3F8S19 Development Board, which contains the following features:

–S3F8S19 48-pin QFP MCU operating at 12 MHz, with 32 KB of internal Flash

memory and 2 KB of internal RAM memory

–USB interface to supply power to the board and used as a PC virtual COM port

with the S3 Monitor and Boot Loader libraries

–LCD module

–Buzzer/Speaker

–UART Connector footprint

–Test Points footprint for all pins of MCU

–MCU current measurement Test Points J7 and J8

–Power Supply level adjustable with potentiometer R16

•

S3 Flash In-System Programmer II

•

ZDSII software, samples, and documentation available free for download

–Sample programs

Figure 1. The S3F8S19 Development Kit

UM026803-0816 Supported Host Environments

S3F8S19 Development Kit

User Manual

Supported Host Environments

The S3F8S19 Development Board supports the following operating systems:

•

Microsoft Windows 7 (32-bit/64-bit)

•

Microsoft Windows 8 (32-bit/64-bit)

Install the ZDSII Software and Documentation

Observe the following steps to download and install your ZDSII software and documenta-

tion.

If you have already installed ZDSII – S3 <version> and have downloaded the software

and documentation by following the procedure on the paper insert in your kit (FL0167),

skip ahead to the next section.

1. Prior to connecting the S3F8S19 Development Board to your development PC, down-

load ZDSII for S3 Family devices version 5.3.0 (or later) from the Downloadable

Software category in the Zilog Store.

2. When the download is complete, unzip the file to your hard drive. Double-click the

installation file named ZDSII – S3_<version>.exe, and follow the on-screen instruc-

tions.

Establish a Connection with the PC

Observe the following procedure to connect the S3 Flash ISP II and S3F8S19 Develop-

ment Board to your PC.

Disconnect or turn off the power to the S3F8S19 Development Board before connecting

or disconnecting the S3 Flash ISP II.

1. Connect the Mini-B side of the USB A (male)-to-Mini-B cable to the S3 Flash ISP II.

Connect the other end of this cable to the PC, as shown in Figure 2.

Note:

Caution:

UM026803-0816 Establish a Connection with the PC

S3F8S19 Development Kit

User Manual

2. Connect the 10p 5x2 ribbon cable to the S3 Flash ISP II, as shown in Figure 3.

3. Connect the other end of the ribbon cable to Jumper J6 on the Development Board.

Ensure that Pin 1 on the ribbon cable is aligned with Pin 1 on the target connector, as

indicated in Figure 4.

Figure 2. Connecting the S3 Flash ISP II to the Development PC

Figure 3. Connecting the 10-pin Ribbon Cable to the S3 Flash ISP II

UM026803-0816 Establish a Connection with the PC

S3F8S19 Development Kit

User Manual

Ensure that you connect the 10 pin ribbon cable using the correct orientation to prevent

damage to the S3 Flash ISP II.

4. With the USB A (male) to Mini-B cable, connect Port P1 on the S3F8S19 Develop-

ment Board to a USB port on the Development PC to apply power to the Development

Board, as indicated in Figure 5.

After completing the procedure to connect the S3F8S19 Development Board to the PC,

the complete setup appears as shown in Figure 6.

Figure 4. Debug Connector J6

Figure 5. Power Supply Port P1 Connector

Caution:

UM026803-0816 Start the S3F8S19 Ledblink Sample Program

S3F8S19 Development Kit

User Manual

Start the S3F8S19 Ledblink Sample Program

The S3F8S19 Development Kit includes a sample program that demonstrates an LED

blinking application. To start the S3F8S19 Ledblink sample program, observe the follow-

ing procedure.

1. Launch ZDSII by navigating from the Windows Start menu to Programs →Zilog

ZDSII –S3 <Version> →ZDSII –S3 <Version>.

2. From the File menu in ZDSII, select Open Project as indicated in Figure 7, and navi-

gate to the following filepath:

<ZDS Install>\samples\S3F8S19\ledblink_asm

Figure 6. The Completed ISP II and Development Board Assembly

UM026803-0816 Start the S3F8S19 Ledblink Sample Program

S3F8S19 Development Kit

User Manual

3. Select the ledblink.zdsproj project from within the ledblink_asm folder as

indicated in Figure 8 and click Open. A list of source files will appear in the Work-

space panel.

Figure 7. The Open Project Selection in the File Menu

Figure 8. Select the ledblink.zdsproj Project

Autres manuels ZiLOG Microcontrôleur

ZiLOG

ZiLOG eZ80F92 Manuel utilisateur

ZiLOG

ZiLOG Z16FMC Series Manuel utilisateur

ZiLOG

ZiLOG eZ80L92 Manuel utilisateur

ZiLOG

ZiLOG Z8F64200100KITG Manuel utilisateur

ZiLOG

ZiLOG Z8 Encore! XP Manuel utilisateur

ZiLOG

ZiLOG Z8F08200100KIT Manuel utilisateur

ZiLOG

ZiLOG ZNEO Series Manuel utilisateur

ZiLOG

ZiLOG Z8 Encore! XP Dual F1680 Series Manuel utilisateur

ZiLOG

ZiLOG Zdots eZ80AcclaimPlus Manuel utilisateur

ZiLOG

ZiLOG Z8 Encore! XP F1680 28-Pin Series Manuel utilisateur

ZiLOG

ZiLOG eZ80F91 Manuel utilisateur

ZiLOG

ZiLOG Z8 Encore! XP F64 Series Manuel utilisateur

ZiLOG

ZiLOG ZMOTION Series Manuel utilisateur

ZiLOG

ZiLOG Zdots eZ80AcclaimPlus Manuel utilisateur

ZiLOG

ZiLOG Z8 Encore! XP 4K Series Manuel utilisateur

ZiLOG

ZiLOG On-Chip Debugger II Z8051 Manuel utilisateur

ZiLOG

ZiLOG Z8051 Series Manuel utilisateur

ZiLOG

ZiLOG Z8 Encore! 8K Series Manuel utilisateur

ZiLOG

ZiLOG Z8 Encore! Manuel utilisateur

ZiLOG

ZiLOG eZ80F92 Manuel utilisateur

ZiLOG

ZiLOG Z8 Encore! XP Instructions d'utilisation et d'entretien

ZiLOG

ZiLOG ZNEO Z16F Series Manuel utilisateur

ZiLOG

ZiLOG Zilog UM014605-0208 Manuel utilisateur

ZiLOG

ZiLOG Z8 Encore! Manuel utilisateur

Manuels Microcontrôleur populaires d'autres marques

AMS

AMS AS7261 Demo Kit Manuel utilisateur

Novatek

Novatek NT6861 Manuel utilisateur

Espressif Systems

Espressif Systems ESP8266 SDK Guide de configuration

Nuvoton

Nuvoton ISD61S00 ChipCorder Mode d’emploi

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manuel utilisateur

Texas Instruments

Texas Instruments Chipcon CC2420DK Manuel utilisateur

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manuel utilisateur

NEC

NEC 78GK0S/K 1+ Series Instructions d'installation et d'utilisation

Mikroe

Mikroe SEMITECH N-PLC Click Instructions d'installation et d'utilisation

Intel

Intel Agilex Manuel utilisateur

Cypress

Cypress CY4607 HX2VL Manuel utilisateur

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manuel utilisateur

Texas Instruments

Texas Instruments TMS320F2837 D Series Manuel utilisateur

CYPRES

CYPRES CY14NVSRAMKIT-001 Manuel utilisateur

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Manuel utilisateur

Espressif Systems

Espressif Systems ESP8266EX Mode d'emploi

Abov

Abov AC33M8128L Manuel utilisateur

Laird

Laird BL654PA Manuel utilisateur