Zeiss LSM 710 Manuel utilisateur

Zeiss LSM 710

1

LSM 710 –Quick Guide MFPL BioOptics - Light Microscopy

Startup

1. Turn on the Main Switch (see image below, #1).

2. Turn on the Systems/PC and Components Switches (see image below, #2).

3. Power up the X-Cite short arc lamp (see image below, #3).

Note: the lamp should not be turned on/off in quick succession. Always wait ca. 20 min.

4. Turn the key of the Argon laser power supply 90° (clockwise) from position 0 to 1 (see below, #4).

5. Turn on the PC (no image shown).

6. After about 5 min, switch the Lasos Argon laser control unit from 'idle' to 'run' (see image below,

#6). Wait until the green and/or red LED on the Lasos control unit lights up. If the red LED shows

up, turn the control knob counterclockwise until only the green LED is on.

Note: if you use only 488 nm at low power, you may leave it in 'idle' mode all the time.

7. Start the software: double-click on the ZEN icon. In the Login dialog, select 'Start System'. Once

ZEN is loaded, select the 'View' menu and check 'Show all (global)'.

Zeiss LSM 710

2

LSM 710 –Quick Guide MFPL BioOptics - Light Microscopy

Shutdown

1. Switch the Argon laser from 'run' to 'idle' (see image below, #1).

2. Turn the key on the Argon laser power supply 90° counterclockwise from position 1 to 0 (see

image below, #2).

3. Close ZEN. In the laser tool window popping up, turn off all lasers (see image below, #3). Turn off

the computer.

4. Turn off the X-Cite lamp (see image below, #4).

5. Push the 'Load position' button on the touch panel (on the microscope table) to lower the

objective (see below, #5). Remove the sample and clean oil objectives with lens cleaning paper.

6. Wait until the fan of the Argon laser has stopped. Then turn off the Systems/PC, Components and

Main Switches (see below, #6).

7. Put the dust cover on the microscope.

Leaving the system for the next user

1. Switch the Argon laser to 'idle' mode (see image above, #1).

2. Push the 'Load position' button on the touch panel (see image above, #5). Remove the sample

and clean oil objectives with lens cleaning paper.

3. In ZEN, close your images. If you have used the 561 and/or 633 nm laser, leave them running.

Leave ZEN running.

4. Disconnect from servers:

HIVE: click on the HIVE icon. In the dialog popping up, select 'Disconnect'

VBC share: click on the 'Logout' icon

Zeiss LSM 710

3

LSM 710 –Quick Guide MFPL BioOptics - Light Microscopy

Troubleshooting

ZEN hangs during startup

1. In the login screen, click on the triangle left to 'Boot Status' (see the image below, #1).

2. Check the messages in the expanding scroll pane (see the image below, #2).

3. If there's a message "No connection to realtime controller", open the the door of the RTC

(black box left to the microscope) , press the Reset Button (see image below, #3) and wait

until ZEN resumes.

Zeiss LSM 710

4

LSM 710 –Quick Guide MFPL BioOptics - Light Microscopy

No excitation light while scanning

1. Check if the Argon laser is turned on (key in position 1, see step #4 in the 'Startup' chapter).

2. On the Main Power unit, check if the Laser key is in ON position (horizontal, see image below).

3. Check if the transmitted light column is in upright position (which activates a magnetic sensor

beneath the column). If seated properly, a LED on the scan head should burn while scanning. If

not, pull the transmitted light column to a fully upright position (see image below).

4. Check the Argon laser power supply for two red LEDs (POWER and INTERLOCK). If the

INTERLOCK LED is off, exit ZEN, power off the power supply and turn it on again (ON/OFF

switch beneath the thick cable. Do NOT use the Mains or Component Switches).

5. Contact the facility if the problem persists.

Autres manuels pour LSM 710

6

Table des matières

Autres manuels Zeiss Microscope

Zeiss

Zeiss 348247-9013-000 Manuel utilisateur

Zeiss

Zeiss Standard 25 ICS Manuel utilisateur

Zeiss

Zeiss AxioObserver D1 Manuel utilisateur

Zeiss

Zeiss Axioskop Manuel utilisateur

Zeiss

Zeiss Axiolab 5 Manuel utilisateur

Zeiss

Zeiss OPMI PRO magis Manuel utilisateur

Zeiss

Zeiss LSM 710 SIM Manuel utilisateur

Zeiss

Zeiss Axiovert 200 Manuel utilisateur

Zeiss

Zeiss Stemi 508 Manuel utilisateur

Zeiss

Zeiss Axiolab A Manuel utilisateur

Zeiss

Zeiss Axiovert 200 Manuel utilisateur

Zeiss

Zeiss Axioscope 5 Manuel utilisateur

Zeiss

Zeiss VISU 200 Manuel utilisateur

Zeiss

Zeiss LSM800-02 Manuel de l'opérateur

Zeiss

Zeiss EXTARO 300 Manuel utilisateur

Zeiss

Zeiss LSM 880 Manuel d'utilisation et d'entretien

Zeiss

Zeiss Axioscope 7 Manuel utilisateur

Zeiss

Zeiss Primostar 3 Manuel utilisateur

Zeiss

Zeiss Stemi 305 cam Manuel utilisateur

Zeiss

Zeiss Stemi 305 Manuel utilisateur

Zeiss

Zeiss LSM 710 Manuel utilisateur

Zeiss

Zeiss Axioskop 2 plus Manuel utilisateur

Zeiss

Zeiss JENAVAL Manuel utilisateur

Zeiss

Zeiss EN10247 Manuel du propriétaire

Manuels Microscope populaires d'autres marques

Thermo Scientific

Thermo Scientific Nicolet iN10 Mode d’emploi

National

National DC3-163 Manuel utilisateur

KERN Optics

KERN Optics OPE-1 Manuel utilisateur

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Manuel utilisateur

Prior

Prior Lux POL Manuel utilisateur

Opitec

Opitec Smartscoop 115615 Manuel utilisateur

KERN

KERN OPO-1 Manuel utilisateur

Topcon

Topcon SP-1P Manuel utilisateur

Motic

Motic PA43 Manuel utilisateur

Leica

Leica DVM5000 Guide de l'utilisateur

MshOt

MshOt MZ62 Manuel utilisateur

KERN Optics

KERN Optics OZR-5 Manuel utilisateur

VWR

VWR VisiScope 384 Series Manuel utilisateur

Nikon

Nikon ECLIPSE E200 POL Manuel utilisateur

Leica

Leica DI C800 Manuel

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manuel utilisateur

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manuel utilisateur

Olympus

Olympus SZ61 Manuel utilisateur