Zacuto HVX200 Manuel utilisateur

Products

Packages

HVX200 Repeatable Focus Ring

Instructions

401 W. Ontario, Suite 250, Chicago, IL 60610

312-863-FILM 888-294-FILM www.zacuto.com

INSTALLATION HVX200 Repeatable Focus Ring

1. Grab the ends of the stainless steel strap with the labels facing into

your hands with tension screw in your right hand.

2. This next step is best done with

the camera on your tripod or

clamped between your legs.

3. Wrap the band around the area between the

focus and zoom barrels. Slide the band underneath

the pin behind the zoom motor.(Figure1)

If necessary angle the leading edge of the band

in toward the lens as you slide it in. (Figure 2)

It may be tight and require some pressure

and finessing.

4. Bring the ends together and

latch the tensioning screw into

place. The two housing ends will

never completely touch. If they

do you have over tightened it.

5. Rotate

stop housing

directly

under the

microphone.

6. Tighten in place with the tensioning screw.

Make sure the band isn’t touching the focus or

zoom barrels (thereshould be just enough room

for the silver band) and don’t over tighten. Just

snug it down enough so that it won’t slide in place.

With the zoom motor switch in manual check the

freedom of movement of the zoom barrel to

ensure that over tightening hasn’t occurred.

Band with stop housing ends

Silver pin

Tension screw

Stop Housing

(final position)

Figure 1 Figure 2

7. With the white side of the red

gear facing the camera, surround

the focus barrel and put the two

halves of the gear together over the

focus ring.

8. While clamping around the focus barrel, mount the gear as close to

the body of the camera as possible without actually touching it.

9. With one hand clamping the gear

together, tighten the two retaining

screws on the white side of the gear.

10. After tightening the lens gear in place (see figure 3), align and straighten the gear on the lens barrel.

Make sure the entire gear is close enough to the stop housing for the pin to engage the white area of the gear.

(see figure 4) For distance (see figure 5) Rotate the lens barrel around several times to gage the gap between

white plastic ring and stop housing so that they are consistent. If not, adjust gear by pushing on the edge that

touches (or is too far away from) the stop housing to get the whole gear equidistant from the stop housing.

NOTES: After being mounted for 15 minutes or so the rubber inside edge of the gear should self center the

gear on the lens barrel for moresmooth operation.

Camera body

Recommended spacing

Gear assembly

Stop pin

INSTALLATION HVX200 Repeatable Focus Ring

Figure 3 Figure 4 Figure 5

OPERATION HVX200 Repeatable Focus Ring

With the red lever down in the stops position,

the lens gear will only have the necessary 270

degrees of rotation. See calibration instructions

below for use in this mode. With the lever in

the up position the lens is in ‘neutral’ and can

rotate continuously.

1. With the camera on, turn

off the auto focus by moving

both switches to manual.

3. Shut off camera. 4. While the camera is

off turn the focus ring

clockwise (facing into

the lens) gently push on

the red lever until you

can drop the red stop

lever all the way down

into the stops position.

5. With the red

stops lever all

the way down,

continue to rotate

the lens clock-

wise until you hit

the stop point.

6. Turn on camera.

You arenow calibrated!

That first stop should be at infinity

and the other stop should be at

about 2’ 10”. If powered down

and the lens barrel rotated, you

must re-calibrate.

CALIBRATION HVX200 Repeatable Focus Ring

2. With the red lever in the

up position, turn the focus

ring to 164 feet. Then move

it just barely past 164 feet

into infinity.

Autres manuels Zacuto Accessoires pour appareils photo

Zacuto

Zacuto Fee-N-G Manuel utilisateur

Zacuto

Zacuto Cine EVF Manuel utilisateur

Zacuto

Zacuto Z-Finder Eyecup Mode d’emploi

Zacuto

Zacuto VCT Universal Baseplate Manuel utilisateur

Zacuto

Zacuto VCT PRO Manuel utilisateur

Zacuto

Zacuto Z-Finder Manuel utilisateur

Zacuto

Zacuto Z-Finder Manuel utilisateur

Zacuto

Zacuto 1-EVF-1S Manuel utilisateur

Zacuto

Zacuto EVF & Z-Finder Recoil Kits Manuel utilisateur

Zacuto

Zacuto Gratical EVF Manuel utilisateur

Zacuto

Zacuto Canon Kit Manuel utilisateur

Zacuto

Zacuto FS5 Z-Finder Manuel utilisateur

Zacuto

Zacuto 1-EVF-1S Manuel utilisateur

Zacuto

Zacuto Canon C100 Z-Finder Manuel utilisateur

Zacuto

Zacuto Axis Mini Manuel utilisateur

Zacuto

Zacuto GH5 Rod Support Base Manuel utilisateur

Zacuto

Zacuto 1-EVF-1S Manuel utilisateur

Zacuto

Zacuto EVA1 Z-Finder Manuel utilisateur

Zacuto

Zacuto DSLR Series Manuel utilisateur

Zacuto

Zacuto Sony F5/F55 Top Plate Manuel utilisateur

Zacuto

Zacuto Sony A7III, A7RIII, A9 Cage Manuel utilisateur

Zacuto

Zacuto Sony FS7 Recoil Kit Manuel utilisateur

Manuels Accessoires pour appareils photo populaires d'autres marques

Viltrox

Viltrox EF-NEX Instructions d'installation

Calumet

Calumet 7100 Series CK7114 Manuel utilisateur

Ropox

Ropox 4Single Series Manuel utilisateur

Cambo

Cambo Wide DS Digital Series Mode d'emploi

Samsung

Samsung SHG-120 Manuel utilisateur

Ryobi

Ryobi BPL-1820 Manuel d'utilisation

Aegis

Aegis ABL-36020P Manuel utilisateur

Pentax

Pentax Data Back Fc Manuel utilisateur

Fantasea

Fantasea EyeGrabber F Series Manuel utilisateur

Honeywell

Honeywell HDZ20HD Manuel utilisateur

EGO

EGO BA1400T Manuel utilisateur

Sima

Sima SRW-62 Manuel utilisateur

Shape

Shape A7SSMKIT Manuel utilisateur

Slide Kamera

Slide Kamera HST-2 Manuel utilisateur

Power works

Power works 2902613 Manuel utilisateur

SES

SES SE-2047-2 Manuel utilisateur

Olympus

Olympus PT-EP05L Manuel utilisateur

Starlite

Starlite OctoDome nxt Manuel utilisateur