Yamaha YFM250X 2002 Manuel
YFM250X(P)
4XE3-AE3
SUPPLEMENTARY
SERVICE MANUAL
2002
FOREWORD
This Supplementary Service Manual has been prepared to introduce new service and new data for
the YFM250X(P) 2002. For complete information on service procedures, it is necessary to use this
Supplementary Service Manual together with the following manual.
YFM250XL’99 SERVICE MANUAL: 4XE3-AE1
YFM250XN 2001 SUPPLEMENTARY SERVICE MANUAL: 4XE3-AE2
YFM250X(P) 2002
SUPPLEMENTARY
SERVICE MANUAL
2001 by Yamaha Motor Co., Ltd.
First Edition, June 2001
All rights reserved.
Any reproduction or unauthorized use
without the written permission of
Yamaha Motor Co., Ltd.
is expressly prohibited.
EB001000
NOTICE
This manual was produced by the Yamaha Motor Company primarily for use by Yamaha dealers
and their qualified mechanics. It is not possible to include all the knowledge of a mechanic in one
manual, so it is assumed that anyone who uses this book to perform maintenance and repairs on
Yamaha machine has a basic understanding of the mechanical ideas and the procedures of
machine repair. Repairs attempted by anyone without this knowledge are likely to render the
machine unsafe and unfit for use.
Yamaha Motor Company, Ltd. is continually striving to improve all its models. Modifications and sig-
nificant changes in specifications or procedures will be forwarded to all authorized Yamaha dealers
and will appear in future editions of this manual where applicable.
N
OTE:
Designs and specifications are subject to change without notice.
IMPORTANT INFORMATION
Particularly important information is distinguished in this manual by the following notations.
The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR
SAFETY IS INVOLVED!
Failure to follow WARNING instructions could result in severe injury or death
to the machine operator, a bystander or a person inspecting or repairing the
machine.
A CAUTION indicates special precautions that must be taken to avoid dam-
age to the machine.
A NOTE provides key information to make procedures easier or clearer.
WARNING
CAUTION:
N
O
TE:
HOW TO USE THIS MANUAL
CONSTRUCTION OF THIS MANUAL
This manual consists of chapters for the main categories of subjects. (See “Illustrated symbols”)
1st title 1: This is a chapter with its symbol on the upper right of each page.
2nd title 2: This title appears on the upper of each page on the left of the chapter sym-
bol. (For the chapter “Periodic inspection and adjustment” the 3rd title
appears.)
3rd title 3: This is a final title.
MANUAL FORMAT
All of the procedures in this manual are organized in a sequential, step-by-step format. The informa-
tion has been compiled to provide the mechanic with an easy to read, handy reference that contains
comprehensive explanations of all disassembly, repair, assembly, and inspections.
A set of particularly important procedure 4is placed between a line of asterisks “*” with each proce-
dure preceded by “●”.
IMPORTANT FEATURES
●Data and a special tool are framed in a box preceded by a relevant symbol 5.
●An encircled numeral 6indicates a part name, and an encircled alphabetical letter data or an
alignment mark 7, the others being indicated by an alphabetical letter in a box 8.
●A condition of a faulty component will precede an arrow symbol 9and the course of action will fol-
low it.
EXPLODED DIAGRAM
Each chapter provides exploded diagrams before each disassembly section for ease in identifying
correct disassembly and assembly procedures.
EB003000
ILLUSTRATED SYMBOLS
Illustrated symbols 1to 9are printed on the
top right of each page and indicate the subject
of each chapter.
1General information
2Specifications
3Periodic checks and adjustments
4Engine
5Carburetion
6Drive train
7Chassis
8Electrical
9Troubleshooting
Illustrated symbols 0to Fare used to identify
the specifications appearing in the text.
0Filling fluid
ALubricant
BSpecial tool
CTorque
DWear limit, clearance
EEngine speed
FΩ, V, A
Illustrated symbols Gto Min the exploded
diagrams indicate the types of lubricants and
lubrication points.
GApply engine oil
HApply gear oil
IApply molybdenum disulfide oil
JApply wheel bearing grease
KApply lightweight lithium soap base grease
LApply molybdenum disulfide grease
MApply silicon grease
Illustrated symbols Nto Oin the exploded
diagrams indicate where to apply a locking
agent Nand when to install a new part O.
NApply the locking agent (LOCTITE)
OReplace
12
34
56
78
90
AB
CD
EF
GHI
J
NO
GEN
INFO SPEC
CHK
ADJ ENG
CARB
DRIV
CHAS
–+
ELEC
TRBL
SHTG
T
R
.
.
EGM
BLS MS
KLM
LT New
CONTENTS
SPECIFICATIONS ............................................................................................1
GENERAL SPECIFICATIONS ..................................................................1
MAINTENANCE SPECIFICATION ............................................................2
ENGINE ................................................................................................2
CHASSIS ..............................................................................................3
ELECTRICAL ........................................................................................3
CABLE ROUTING .....................................................................................4
PERIODIC CHECKS AND ADJUSTMENTS ..................................................12
INTRODUCTION .....................................................................................12
PERIODIC MAINTENANCE/LUBRICATION INTERVALS.......................12
CHASSIS .................................................................................................14
ADJUSTING THE FRONT BRAKE .....................................................14
ADJUSTING THE REAR BRAKE LIGHT SWITH ...............................14
ELECTRICAL .................................................................................................15
CHECKING THE SWITCH ......................................................................15
CHECKING THE SWITCH ..................................................................15
CHECKING A SWITCH SHOWN IN THE MANUAL ...........................15
SIGNAL SYSTEM ...................................................................................16
CIRCUIT DIAGRAM ............................................................................16
CHECKING THE SIGNAL SYSTEM ...................................................17
YFM250X(P) 2002 WIRING DIAGRAM
–1 –
SPEC
GENERAL SPECIFICATIONS
SPECIFICATIONS
GENERAL SPECIFICATIONS
Item Standard
Model code: 4XEF (CDN, Europe and Oceania)
Dimensions:
Overall length 1,940 mm (76.4 in)
Overall width 1,080 mm (42.5 in)
Overall height 1,118 mm (44.0 in)
Seat height 780 mm (30.7 in)
Wheelbase 1,170 mm (46.1 in)
Minimum ground clearance 150 mm (5.9 in)
Minimum turning radius 2,900 mm (114.2 in)
Brake:
Front brake type Dual disc brake
operation Right hand operation
Rear brake type Drum brake (fully sealed)
operation Left hand and right foot operation
Electrical:
Ignition system DC.C.D.I.
Generator system A.C. magneto
Battery type YB14A-A2
Battery capacity 12 V 14 AH
Bulb wattage ×quantity:
Headlight 12 V 25 W/25 W ×2
Tail/brake light 12 V 5 W/21 W ×1
Indicator lights:
Neutral 12 V 1.7 W ×1
Reverse 12 V 1.7 W ×1
–2 –
SPEC
MAINTENANCE SPECIFICATIONS
MAINTENANCE SPECIFICATIONS
ENGINE
Item Standard Limit
Cylinder head:
Warp limit ---- 0.03 mm
(0.001 in)
Measuring point Lines indicate straightedge
measurement.
Piston:
Piston to cylinder clearance 0.04 ~ 0.06 mm
(0.0016 ~ 0.0024 in)
0.15 mm
(0.0059 in)
Piston size “D”70.92 ~ 70.97 mm
(2.792 ~ 2.794 in)
----
Measuring point “H”4.0 mm (0.16 in) from bottom line
of piston skirt
----
Oversize 2nd 71.5 mm (2.81 in) ----
Oversize 4th 72 mm (2.83 in) ----
Piston off-set 0.5 mm (0.02 in) ----
Piston off-set direction Intake side ----
Piston pin bore inside diameter 16.002 ~ 16.013 mm
(0.6300 ~ 0.6304 in)
----
Piston pin outside diameter 15.991 ~ 16.000 mm
(0.6296 ~ 0.6299 in)
----
Lubrication system:
Oil filter type Wire mesh ----
Oil pump type Trochoid type ----
Tip clearance “A”or “B”0.15 mm (0.006 in) 0.20 mm
(0.008 in)
Side clearance 0.04 ~ 0.09 mm
(0.002 ~ 0.004 in)
0.09 mm
(0.004 in)
Bypass valve setting pressure 80 ~ 120 kPa
(0.8 ~ 1.2 kg/cm2, 11 ~ 17 psi)
----
Oil pressure (hot) 52 kPa (0.52 kg/cm², 7.5 psi) at
7,500 r/min
----
Pressure check location Element cover ----
*
H
D
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels Yamaha Moto
Yamaha
Yamaha R7 2022 Manuel utilisateur
Yamaha
Yamaha FJR1300AS Manuel utilisateur
Yamaha
Yamaha TW200Z Manuel utilisateur
Yamaha
Yamaha TT-R110E 2018 Manuel utilisateur
Yamaha
Yamaha Tenere 700 Manuel utilisateur
Yamaha
Yamaha Star XV17PCX Manuel utilisateur
Yamaha
Yamaha FZ8-NA Manuel utilisateur
Yamaha
Yamaha 2009 V Star XVS250X Manuel utilisateur
Yamaha
Yamaha CY50B Manuel utilisateur
Yamaha
Yamaha FJR1300 Manuel utilisateur
Yamaha
Yamaha SR400 2022 Manuel utilisateur
Yamaha
Yamaha PW80(T) Manuel utilisateur
Yamaha
Yamaha YZF-R1 2022 Manuel utilisateur
Yamaha
Yamaha TT-R Manuel utilisateur
Yamaha
Yamaha FJR1300A Manuel utilisateur
Yamaha
Yamaha TT-R125(M) Guide d'application
Yamaha
Yamaha YBR 125K Manuel utilisateur
Yamaha
Yamaha TT-230RA Manuel utilisateur
Yamaha
Yamaha XSR900 2019 Manuel utilisateur
Yamaha
Yamaha 2003 FJR1300 Manuel utilisateur
Manuels Moto populaires d'autres marques
APRILIA
APRILIA ETV MILLE CAPONORD - PART1 02-2001 Manuel utilisateur
KTM
KTM Freeride E-XC 2021 Manuel utilisateur
Fantic
Fantic Enduro 125 Manuel utilisateur
Ducati
Ducati Supersport 750 desmodue Manuel utilisateur
MV Agusta
MV Agusta 2008 F4 312RR 1078 Manuel d'instructions
Ducati
Ducati 748 monoposto strada Manuel utilisateur
ATK
ATK 1988 250 Manuel utilisateur
Excelsior-HENDERSON
Excelsior-HENDERSON 1999 HCX Manuel utilisateur
Triumph
Triumph Thunderbird Manuel utilisateur
Ducati
Ducati 996 Manuel utilisateur
BMW
BMW MOTORRAD K 1200 R Sport Manuel d'installation et d'entretien
BMW Motorrad
BMW Motorrad G 650 GS 2007 Manuel d'installation et d'entretien