Yamaha DX7mega128 Manuel

DX7mega128 Page 1 of 6 Install v1.20

www.musictechnologiesgroup.com Preliminary

Yamaha DX7mega128 Expansion Install

1: Introduction

The DX7mega128 a powerful option board that provides increased memory and greater control of

the DX7.

While the installation is fairly simple, it still requires patience and general electronics

knowledge. We accept no responsibility for the work you perform on your DX7. Read over

the following installation description and if you feel you are not capable of the work

required, turn the project over to a qualified technician

Precautions!

High Voltage Safety Warning

Unplug the audio cable. Turn the DX7 power switch OFF and unplug it from the wall.

Disconnect any other connected cables before opening the DX7.

ESD Precautions and Proper Handling Procedures

You should observe standard static-safe handling behavior when working with sensitive electronic

equipment such as synthesizers:

o Avoid carpets in cool, dry areas.

o Dissipate static electricity before handling any system components by touching a

grounded metal object.

o If possible, use anti-static devices, such as wrist straps and floor mats.

o Take care when installing the board. Prevent damage to the connectors by aligning

connector pins before you apply pressure. A damaged pin can render the board unusable

and can cause damage to system components at power-on.

o If disconnecting a cable, always pull on the cable connector, not on the cable itself.

Tools Required

o Standard Philips screwdriver.

o Standard flat-head screwdriver (small).

Condition of DX7

While the DX7mega128 will replace the functionality of damaged or missing EPROM and/or

SRAM chips, it will not correct other problems your vintage synthesizer may have. It is

recommended that the synth be in otherwise good condition before beginning the installation. For

instance, the battery voltage should be checked and the battery replaced/repaired by a tech if

necessary. Sockets for the EPROM and SRAM chips should be in good working order and not be

DX7mega128 Page 2 of 6 Install v1.20

www.musictechnologiesgroup.com Preliminary

dirty, oxidized, rusted or otherwise compromised. If repair is required, do it before installing

DX7mega128.

2: Installation





Back up your patches if they are important to you!

Open the DX7

Using a Philips head screwdriver, remove the 5 screws from the front panel. Two are located

on the left front. Two are located on the right front. A final one is located on the right rear. Set the

screws aside, noting that the rear panel one is the shortest.

(Re)Move the Keybed & Remove the Keyboard Rail

It can be difficult to see the delicate pins when installing the DX7mega128 board. By moving the

keybed (the chassis with the keys) and removing the silver keyboard rail, you will have better

sight lines and freedom of movement when installing the DX7mega128 board.

Remove the 4 large external screws from the underside of the keyboard along the front

edge. The photo below shows the inside front edge of the empty case bottom and illustrates the

location of the 4 screws. You will, of course, be unscrewing from the DX7 underside.

Loosen the 3 internal screws at the extreme right and left ends that hold the keybed in

place. It is not necessary to extract them from the holes they reside in.

DX7mega128 Page 3 of 6 Install v1.20

www.musictechnologiesgroup.com Preliminary

Carefully lift the keybed slightly up and out (toward yourself) an inch or so.. You don't need

to move it much. You will probably need to free up one or more cables to accomplish it. Or if you

prefer, disconnect the cables and completely remove the keybed.

This will give you access to the 3 screws holding the silver keyboard rail in place. Remove those

three screws and set aside the silver keyboard rail. (Shown here with keybed removed).

You now have excellent

access to the DX7 main

board. If you do remove the

keybed you may find it easier

to remove the small yellow

cable and large flat grayish

cable at the main-board-end

rather than from the keybed.

You will also need to unclip

two small cables on the left

end (mod wheel and pitch

bend). There may also be

wire tires and/or cable

fasteners to deal with.

Remove the EPROM and SRAM ICs

The next step is to remove the EPROM and two SRAM ICs.

The EPROM is found in location IC14 and the two M5M5118P SRAM chips (or similar) are

located at IC21 and IC20.

Remove them by prying slowly at each end of the chip back-and-forth with a small flat-head

screwdriver. Avoid touching any of the metal pins with the screwdriver.

DX7mega128 Page 4 of 6 Install v1.20

www.musictechnologiesgroup.com Preliminary

Place them safely aside on anti-static foam. You can use the reverse side of the foam shipped

with the DX7mega128.

The photo above shows the 3 chips removed.

After removing the chips, also remove the screw shown at the

center of these photos near IC23.

Install the DX7mega128 Printed Circuit Board

Hand tighten the supplied nylon standoff into the screw position near IC23. Tighten it well by

hand, but there is generally no need to use a tool. Do not over tighten or strip the threads.

Remove the DX7mega128 board from the anti-static foam. Inspect the bottom of the board to

make sure none of the pins have been damaged. You should see one collection of 28 pins (2

parallel strips of 14 pins), one strip of 12 pins and a strip of 8 pins.

DX7mega128 Page 5 of 6 Install v1.20

www.musictechnologiesgroup.com Preliminary

Place the DX7mega128 board gently on the DX7 main board so that the 28 pins that form a DIP

package align with the vacated IC14 spot. The 8 pins along the edge should align with IC20. Do

not press the board in place yet. You can use a small mirror to check the pin alignment.

Once you are happy that all the pins are aligning with the desired locations, firmly and evenly

press the DX7mega128 board in place. Make a visual check to see that the board is flush with the

sockets.

Using a screwdriver, carefully tighten the original main board screw through the DX7mega128

board into the nylon standoff. Again do not force it or over tighten as this can not only strip

the standoff, but it can cause the DX7mega128 board to change position. It should be tight

enough so that it cannot work lose. Double check the pins.

Reassembly

Remove all tools from the DX7. Carefully reassemble the DX7 in the reverse order, taking care to

replace the correct screws in the various locations. If you disconnected the green keybed ground

strap wire don't forget to screw it back in.

Test

Plug the AC cable in and turn it on. After a few moments, you should get a greeting message like:

* Welcome to *

* DX7mega128 *

DX7mega128 Page 6 of 6 Install v1.20

www.musictechnologiesgroup.com Preliminary

You can do a quick version check of the board by pressing and holding the brown FUNCTION

button and also pressing and holding buttons 16 and 32. You should see something like the

following:

DX7mega128

Version 1.20

Press the green INTERNAL button twice.

Initialization

Since technically the battery has been removed, you may find some of the standard DX7 function

settings have been scrambled. Follow the steps below to put the DX7 into a known good state

before loading your patches back in.

1. Press MEMORY PROTECT / INTERNAL then OFF.

Internal memory protect is now off.

2. Press FUNCTION and then button 13 or button 12 repeatedly until you see FUNCTION

CONTROL Func/Patch. Press NO to set this value to OFF.

There is now one global set of function parameters for the DX7 (later you will see

how to change this so that each patch can have its own function parameters).

3. Press button 13 or 12 again until you see FUNCTION CONTROL Func Data INIT? Press

YES to set the function parameters to the default state.

4. Press button 13 or 12 again until you see FUNCTION CONTROL Volume= and make sure

this level is turned up using the DATA ENTRY slider or YES button.

Check/set the standard DX7 Function settings versus your preferences. You should be able to

load some patches now, but it is still possible that some setting prevents the sound from being

heard.

The patch data memory will certainly be garbled. Use the standard DX7 panel operations to load

the current data bank with your patches. The “Yamaha DX7mega128 Expansion User Guide”

will explain how to select memory banks as well as how to use the other features of this

expansion.

Enjoy your updated DX7!

See the MTG web site for more great vintage synth and drum machine goodies.

Table des matières

Autres manuels Yamaha Matériel informatique

Yamaha

Yamaha mLAN8E Manuel utilisateur

Yamaha

Yamaha MMP1 Manuel utilisateur

Yamaha

Yamaha DME Designer Guide de l'utilisateur

Yamaha

Yamaha MY8-AEB Manuel utilisateur

Yamaha

Yamaha PLG150-AN Manuel utilisateur

Yamaha

Yamaha F1040 Manuel utilisateur

Yamaha

Yamaha DX7-4X-EXP Manuel utilisateur

Yamaha

Yamaha RM-CR Manuel utilisateur

Yamaha

Yamaha MEP4 Manuel utilisateur

Yamaha

Yamaha PLG100-DX Manuel utilisateur

Yamaha

Yamaha MTX3 Manuel utilisateur

Yamaha

Yamaha DX7mega128 Manuel utilisateur

Yamaha

Yamaha DP100 Manuel utilisateur

Yamaha

Yamaha DP100 Manuel utilisateur

Yamaha

Yamaha R-100 Manuel utilisateur

Yamaha

Yamaha DX7 DX-MAX(3)+ Manuel utilisateur

Yamaha

Yamaha PLG150-PF Manuel utilisateur

Yamaha

Yamaha MTX5-D Manuel utilisateur

Yamaha

Yamaha MY8-SDI-ED Manuel utilisateur

Yamaha

Yamaha MY4-AD Manuel utilisateur

Yamaha

Yamaha SP2060 Manuel utilisateur

Yamaha

Yamaha DSP-A700 Manuel utilisateur

Yamaha

Yamaha S90 Manuel utilisateur

Yamaha

Yamaha SPX2000 Editor Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur