Yale SDA16 Manuel utilisateur

SDA16

Stand-Alone Alarm Device

Installation Instructions

An ASSA ABLOY Group brand

80-9470-0330-000 (01-13)

EMERGENCY EXIT - ALARM WILL SOUND

An ASSA ABLOY Group brand

80-9470-0330-000 (01-13)

1. Frame and Door Preparation

Frame

Edge

Horizontal

Reference

Line

Out-swinging Door In-swinging Door

DOOR

Frame

1. For installation on an In-swinging Door, mark a

Vertical Reference Line 1-15/16"(50mm) off of the

Frame Edge, also decide the vertical placement and

mark a Horizontal Reference Line. Align template

as shown with Vertical and Horizontal Reference Lines.

2. Use a center punch to mark door for

(2) .144"(3.7mm) Dia. (#27 Drill) mounting holes

for the Device Mounting Base (Shown Below).

3. Use a center punch to mark frame for (2) .099"(2.5mm) Dia.

(#39 Drill) holes for the Magnet (Shown Below).

4. If outside Cylinder Control Option is to be used,

bore a 1-1/4"(32mm) Dia. Hole thru door. Fig. 2 ‘B’ Hole

5. For Hardwire option requiring door preparation, mark and

bore a 1"(25mm) Dia. Hole to required depth. Fig. 2 ‘C’ Hole

6. Install Magnet to door frame with (2) #4 screws supplied.

1. For installation on an Out-swinging Door,

mark a Vertical Reference Line 2-3/16"(56mm)

off of the Frame Stop, also decide the vertical

placement on the door and mark a Horizontal

Reference Line. Fold template as shown and

align with Vertical and Horizontal Reference Lines.

2. Use a center punch to mark door for

(2) .144"(3.7mm) Dia. (#27 Drill) mounting holes

for the Device Mounting Base (Shown Below).

3. Use a center punch to mark frame for

(2) .099"(2.5mm) Dia. (#39 Drill) holes for the Magnet

(Shown Below).

4. If outside Cylinder Control Option is to be used,

bore a 1-1/4"(32mm) Dia. Hole thru door. Fig. 1 ‘B’ Hole

5. For Hardwire option requiring door preparation, mark and

bore a 1"(25mm) Dia. Hole to required depth. Fig. 1 ‘C’

Hole

6. Install Magnet to door frame with (2) #4 screws supplied.

Vertical

Reference

Line

Vertical

Reference

Line

Horizontal

Reference

Line

Figure 2

Figure 1

Arrows on the magnet face toward the

alarm housing and away from the door.

Arrows on the magnet face toward the

alarm housing and away from the door.

An ASSA ABLOY Group brand

80-9470-0330-000 (01-13)

TYPICAL MORTISE CYLINDER

Use standard 1-1/8" mortise cylinder with cam.

Cylinder Collar is not required.

Cylinders

3. Device Handing Change2. Installing Cylinder

1. Insert mortise cylinder through hole in the Housing.

2. Orient keyway to the 6 o’clock position, adjust as needed.

3. Assemble cylinder actuator onto the cylinder from inside

as shown below. The split tabs should be oriented towards

the controller board (12 o’clock position), trapping the

toggle switch on the printed circuit board. Fig. 4

Caution: Carefully install Actuator without damaging the

Toggle Switch.

4. Attach cylinder nut to cylinder, rotate clockwise until secure.

NOTE: Actuator should be free to rotate, by installing in

position shown.

Orient

Arrow

towards

Door Edge

1. Remove (2) screws retaining the magnet sensor

and set components aside.

2. Remove (2) screws retaining the Tamper Switch and

exchange locations of both components (See Figure 5).

3. Reattach components with the screws.

NOTE: a.The arrow on the magnet sensor should face outward,

towards the edge of the door (See Figure 5).

b. Replace wires behind ribs in cover to protect them

from moving parts.

4. Remove and relocate tamper switch contact from mounting

base to opposite location as shown below (See Figure 6).

5. Reattach with (2) screws.

Tamper Switch

Contact

Figure 6

3/4

(19)

123456

(+)

(—)

Figure 5

Tamper

Switch

Magnet

Sensor

±1/16

Rib

(Note Position)

Cylinder Nut

Cylinder

Actuator

Mortise

Cylinder

Alarm

Housing

Figure 3

Toggle

Switch

Cylinder

Actuator

Figure 4

An ASSA ABLOY Group brand

80-9470-0330-000 (01-13)

4. Standard Installation

6. Standard Device x Outside Cylinder Control Installation

3. Attach mounting base to door, wall or Gang Box following

previous instructions from Step 4 or 5.

4. With mounting base securely attached to door,

insert cylinder and ring through prep on opposite

side of door, fasten securely with (2) cylinder screws

inserted through slotted holes in the mounting base

(See Figure 10).

NOTE: Cylinder Screws and Collar are supplied with

the cylinder, when required.

5. Hardwire Installation

Note: Hardwire options require wire harness within the door or

wall and may require door position switches (DPS) or other means

of activation. This unit is equipped to accept the Electrolynx™ quick

connect system. See catalog for wiring harness and power supply

details.

1a. Door Mounted. After preparing the door, remove Knockout Plug

and attach the Mounting Base to the door through holes “A” &

“D”, using (2) #10 screws provided.

NOTE: Knockout Plug will accept standard 1/2" electrical nipple

to protect wires.

1b. Wall Mounting. This unit may be mounted between two doors,

to monitor both doors (TIP: Attach unit to a wall stud).

1c. Wall Mounting to a single “Gang Box”. Attach the Mounting

Base through holes “A” and “X”, using standard gang box

screws as shown in Figure 8 (Gang Box screws not provided).

Attach Alarm Housing per section 4.2 & 4.3 (Standard Installation).

Hole “D”

Hole “X”

(*Gang Box Only)

Hole “A”

1. After preparing the door, attach the Mounting Base

to door through holes “A” & “D”, using (2) #10 screws

provided, as shown below.

2. Attach Alarm Housing over hook at the upper end

of mounting base. Pull downward and press towards

the door, until housing is flush with surface of door.

3. Engage housing key into the bottom cylinder, underneath

lower edge of housing. Rotate clockwise until positive

latch is made.

NOTE: Check that Device is secure to the Door.

Knockout

Plug

(Remove for

Wire Routing)

Catch Hook

Clip Retainer

Hole “A”

1. If not pre-assembled insert Cam Bushing Assembly

through mounting base from the back side

(See Figure 9) and install retainer clip onto exposed

groove on bushing.

2. Orient cam bushing assembly so that the long end of the

pin is vertical (UP) in the 12 o’clock position.

Rim Cylinder

Cylinder Collar

(when required)

(2) Cylinder

Mounting Screws

Figure 8

Figure 10

Cam Bushing

Assembly

Figure 9

Figure 7

Refer to Page 5 for Alarm Function Adjustments

Before proceeding with Step 4

!! !!

An ASSA ABLOY Group brand

80-9470-0330-000 (01-13)

ALARM FUNCTION AS SHIPPED

1) Upon arming, LED will flash AMBER and the device will allow egress without triggering alarm for 7 seconds.

2) After 7 seconds, alarm will chirp one time and the device will be ARMED.

The LED will flash RED every 30 seconds, indicating the device is ARMED.

3) Once the device is ARMED, egress will result in an alarm sound that will stop only when the device is RESET

by key or remote.

4) Low Battery Indicator - Alarm will chirp every 10 seconds, indicating battery needs to be replaced.

• Alarm PC Board has Dip Switches DS-1, 2, 3, 4, and 5 factory preset per Tables 1, 2, and 3 shown below.

• Dip Switch DS-6 is for “hard wire”configurations and setting does not affect stand-alone battery operation.

REX and Passage Time Delay TABLE 1

DS-1 DS-2 Timer Delay

*Off *Off 7 Seconds

Off On 10 Seconds

On Off 15 Seconds

On On 20 Seconds

Automatic Alarm Reset TABLE 2

DS-3 DS-4 Reset Time

Off Off 2 Minutes

Off On 5 Minutes

On Off 10 Minutes

*On *On No Auto Reset

every 30 seconds instead of RED to indicate a violation

has occurred.

Armed and Violation LED Color Selection TABLE 3

Device is shipped standard, per Table 3, so that RED LED

flashes every 30 seconds when device is ARMED, and

flashes GREEN every 30 seconds under auto reset, when

door has been violated.

When the device is initially ARMED by key, the LED

will flash AMBER and allow egress for a time defined

in Table 1.

PassageDS-5 Armed

LED Color

Armed Violation

LED Color

Off

Red

Green

Amber

Factory Preset

Amber

Green

Red

NOTES:

1 2 3 4 5 6

123456

Dip Switch Settings

Enlarged View

Black

Battery plugs in place with polarity

connected as shown

(+)

(—)

Battery

Bracket

* The unit is shipped with power disconnected, attach battery connector as shown below.

The alarm can be set so that it will reset itself after a

violation has occurred per Table 2. If the device

automatically resets, the indicator light will flash GREEN

When the unit is hard wired, DS-6 must be in the “On” position for remote monitoring thru connector J3.

An ASSA ABLOY Group brand

80-9470-0330-000 (01-13)

•

Alarm will not sound

Alarm sounds when keyswitch

is activated.

Alarm chirps every 10 seconds.

ARMED indicator LED, wrong

color.

Problem

TROUBLESHOOTING

•

Battery is not connected.

Battery needs replacing.

Alarm is not ARMED. Turn key clockwise.

Magnet Sensor is not installed correctly. Verify

that the proper handing applies (See Step 3, Figure 5).

Tamper Switch is not closing when Alarm Housing

is installed. Make sure Switch Contact is located in the

correct position (See Step 3, Figure 6). Verify that the

Alarm Housing is installed correctly.

J2 connector not installed, or loose.

Low battery indicator, replace battery.

Change position of DS-5 Dip Switch.

“OFF” for RED ARMED indicator.

“ON” for GREEN ARMED indicator.

Solution

Yale® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Other products' brand names may be trademarks or registered trademarks of their

respective owners and are mentioned for reference purposes only. These materials are protected under U.S. copyright laws. All contents current at time of publication.

Yale Security Inc. reserves the right to change availability of any item in this catalog, its design, construction, and/or its materials.

2005, 2013

Product Support Tel 800. • www.yalelocks.com810.WIRE (9473)

Yale Locks & Hardware is a division of Yale Security Inc., an ASSA ABLOY Group company.

An ASSA ABLOY Group brand

80-9470-0330-000 (01-13)

Frame Edge

(Do Not Fold)

Vertical

Reference

Line

Frame Edge

(Do Not Fold)

CDevice Template

(In-Swinging Door)

3/8"

(10)

1-15/16"

(50)

13/16"

(21)

13/16"

(21)

1-9/16"

(40)

3-3/4"

(95)

1-21/32"

(42)

3/8"

(10)

1-15/16"

(50)

13/16"

(21)

1-21/32"

(42)

1-1/4"

(32)

(25)

Dia. #27 Drill

Dia.

.144

(4)

Dia. Thru

Dia. #27 Drill

.144

(4)

.099

(3)

Dia.

#39 Drill 2x .099

(3)

Dia.

#39 Drill

1/2"

(13)

(Ref)

1-15/16"

(50)

Magnet and

Cylinder located

on same centerline

(Arrow on Magnet

oriented towards

Alarm Housing

Assembly).

DOOR

Locate off

of edge to

clear swing

of door

CAUTION: Office copiers and facsimile mach-

ines may change the size of a drawing and make

the template inaccurate to use as a door marker.

If this is not the original template packed with the

trim, use only the holes on the door (do not use

template as a door marker).

Standard Install

Hardwire Option

Std. Install x

Outside Cylinder

FUNCTION

A, D, E

A, C, D, E

A, B, D, E

* Hardwire Option Only

“D”

“C”

“B”

“A”

“E”

“E”“E”

“E”

Horizontal

Reference

Line

Frame Edge

(Fold Line)

Frame Edge

(Fold Line)

CDevice Template

(Out-Swinging Door)

CAUTION: Office copiers and facsimile mach-

ines may change the size of a drawing and make

the template inaccurate to use as a door marker.

If this is not the original template packed with the

trim, use only the holes on the door (do not use

template as a door marker).

Standard Install

Hardwire Option

Std. Install x

Outside Cylinder

FUNCTION

A, D, E

A, C, D, E

A, B, D, E

Dia. #27 Drill

.144

(4)

1-9/16"

(40)

3-3/4"

(95)

3/8"

(10)

2x .099

(3)

Dia.

#39 Drill

13/16"

(21)

1-21/32"

(42)

2-3/16"

(56)

2-3/16"

(56)

(25) Dia.

1-1/4"

(32) Dia. Thru

13/16"

(21)

Dia. #27 Drill

.144

(4)

13/16"

(21)

3/8"

(10)

.099

(3)

Dia.

#39 Drill

1-21/32"

(42)

2-3/16"

(56)

3/16"

(5) (Ref.)

1/16"

(2)

Magnet and

Cylinder located

on same centerline

(Arrow on Magnet

oriented away

from Door).

DOOR

* Hardwire Option Only

“D”

“C”

“B”

“A”

“E”

Horizontal

Reference

Line

Vertical

Reference

Line

An ASSA ABLOY Group brand

80-9470-0330-000 (01-13)

Table des matières

Autres manuels Yale Système de sécurité

Yale

Yale HSA6092 Manuel utilisateur

Yale

Yale SAA8011 Manuel utilisateur

Yale

Yale HSA 6300 Manuel utilisateur

Yale

Yale Smart Living HSA6210-R Manuel utilisateur

Yale

Yale YL-SR-320 Manuel utilisateur

Yale

Yale AC-PETPIR Manuel utilisateur

Yale

Yale Sync IA-310 Manuel utilisateur

Yale

Yale Smart Living SV-4C-2ABFX Manuel utilisateur

Yale

Yale HSA3400 Manuel utilisateur

Yale

Yale SR-310 Manuel utilisateur

Yale

Yale EF-IPBox Manuel utilisateur

Yale

Yale HSA6200 Manuel utilisateur

Yale

Yale HSA 3500 Manuel utilisateur

Yale

Yale SR-310 Manuel utilisateur

Yale

Yale IA-210 Manuel utilisateur

Yale

Yale SAA8021 Manuel utilisateur

Yale

Yale SV-4C-2ABFX-2 Manuel utilisateur

Yale

Yale IA-230 Manuel utilisateur

Yale

Yale SAA8012 Manuel utilisateur

Yale

Yale SR-310 Manuel utilisateur

Yale

Yale HSA6600 Manuel utilisateur

Yale

Yale Distress alert system Manuel utilisateur

Yale

Yale HSA3800 Manuel utilisateur

Yale

Yale HSA3095 Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur