Yale Conexis Mode d’emploi
Installing the Yale Access Module – Conexis
Installing the Module
Step 1. Remove battery cover
Using a Phillips-head screwdriver, loosen the battery cover screw. Slide the cover away from the lock.
Step 2. Remove a battery
Remove the batteries from your lock to power it off. Wait approximately 10 seconds for the lock to fully
power down.
Step 3. Remove the Module Cover
Slide the module cover up to remove this and access the slot
Step 4. Install the Module
Insert the Yale Access module into the slot in the module compartment. Make sure it is
properly seated in the lock.
Step 5. Replacing the battery cover
Restore power to the lock by reinserting the batteries. The light on the front of the lock will flash
blue and play a fanfare noise, once this has happened please proceed.
Step 6. Registering the Module & replacing the cover
Follow the below steps to register the Yale Access module with your lock.
Installing Yale Access Application
Before you get started, download the Yale Access App from either the Apple Store or Google Play
depending on whether you use an iOS or Android phone:
Yale Access devices come with a QR code that can be used to set up the device in the Yale Access App. This
code is included on the Yale Access Module and is helpful during setup. If you no longer have a QR code
associated with the device, the serial number can be used during setup.
1. Open the Yale Access App
2. Select the menu in the top-left corner
3. Select Set up a Device to access the QR code scanner
4. Scan the code. If you are unable to scan it, select Can’t Scan the Code to set up with the Serial
Number, which is the 10-digit number located on the sticker inside the battery cover.
5. Follow in-app instructions to complete setup steps
Step 7. Set up the Yale Connect Wi-Fi Bridge
Visit below article for step-by-step instructions to set up the Yale Connect Wi-Fi bridge with your lock.
Setting Up Yale Connect Wi-Fi Bridge
Yale Connect Wi-Fi Bridge serves as a Wi-Fi bridge between our Servers and your Smart Lock
so you can lock and unlock your Smart Lock remotely, right from your phone. With Yale
Connect Wi-Fi Bridge, you can instantly let visitors into your home when you're not there.
Requirements
•Make sure your device has Wi-Fi turned on (Settings > Wi-Fi)
•Make sure your phone is connected to your home Wi-Fi network (Yale Connect Wi-Fi Bridge is
compatible with 2.4 gHZ Wi-Fi)
•The Yale Connect Wi-Fi Bridge requires an active Yale Smart Lock and needs to be installed using
a compatible phone. Please visit our phone compatibility page to ensure that your phone is
compatible.
To install your Yale Connect Wi-Fi Bridge:
For optimal performance and reliability, plug Yale Connect Wi-Fi Bridge into a power socket
that is within 15 feet on an opposite or adjacent wall from your Yale Smart Lock.
1. Wait for the flashing green light on your Yale Connect Wi-Fi Bridge. If you don’t see the flashing
green light press and hold the button on your Yale Connect Wi-Fi Bridge for 5 seconds.
2. In the Yale Access App, go to the side menu (upper left), tap Set Up New Device.
3. Choose Set Up a Connect Bridge.
4. Choose a lock with which to associate your Yale Connect Wi-Fi Bridge.
5. When prompted, plug connect Bridge into a socket near your door and then follow the in-app
instructions.
The accessory setup interface will ask you to choose your home Wi-Fi network. Once your Yale
Connect Wi-Fi Bridge has successfully joined your home Wi-Fi network, the Yale Access App
will check the signal levels of your Wi-Fi and bluetooth connections. If your signal levels are
good, you’re almost finished. If your signal levels are low, you will be guided through adjusting
the location of your Yale Connect Wi-Fi Bridget to improve its connection.
If you experience issues joining your Yale Connect Wi-Fi Bridge with your Wi-Fi network, this
article provides troubleshooting steps.
Yale Connect Wi-Fi Bridge displays its current status through different LED indicator lights on
the front of the device. This article helps you determine what the LED indicators on Yale
Connect Wi-Fi Bridge mean as well as any troubleshooting steps you can take to improve
functionality.
Table des matières
Autres manuels Yale Unité de contrôle
Yale
Yale Z-Wave Plus Manuel utilisateur
Yale
Yale Z-Wave Plus YRMZW2-US Manuel utilisateur
Yale
Yale Real Living iM1 Caractéristiques techniques
Yale
Yale iM1 Manuel utilisateur
Yale
Yale Real Living ZigBee Module Caractéristiques techniques
Yale
Yale MD-05 Manuel utilisateur
Yale
Yale SECURE CONNECT iM1 Caractéristiques techniques
Yale
Yale real Living iM1 Caractéristiques techniques
Yale
Yale Z-Wave Plus v2 Manuel utilisateur
Yale
Yale Real Living YRMZB2 Caractéristiques techniques
Manuels Unité de contrôle populaires d'autres marques
Festo
Festo Compact Performance CP-FB6-E Manuel de la liste des pièces
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur
JS Automation
JS Automation MPC3034A Manuel utilisateur
JAUDT
JAUDT SW GII 6406 Series Guide rapide
Spektrum
Spektrum Air Module System Manuel utilisateur
BOC Edwards
BOC Edwards Q Series Manuel utilisateur
