Yacht Devices YDOG-01 Manuel utilisateur
User Manual
Outboard Gateway YDOG-01
also covers models
YDOG-01N, YDOG-01R
Firmware version
1.00
2021
© 2021 Yacht Devices Ltd. Document YDOG-01-001. August 8, 2021.
Web: http://www.yachtd.com/
NMEA 2000® is a registered trademark of the National Marine Electronics
Association. SeaTalk NG is a registered trademark of Raymarine UK Limited.
Garmin® is a registered trademark of Garmin Ltd.
Contents
Introduction 4
Warranty and Technical Support 5
I. Specication 6
II. Device Installation and Connection to NMEA 2000 8
III. Connection to the Engine and Initial Setup 10
IV. LED Signals 15
V. Conguration with a Hidden Button 17
VI. Conguration with Installation Description Strings 19
VII. Firmware Updates 26
Appendix A. Troubleshooting 28
Appendix B. NMEA 2000 Messages Supported by Device 30
Package Contents
Device 1 pc.
This Manual 1 pc.
Paperclip for reset 1 pc.
NMEA 2000 Drop Cable not supplied
Note: Device can be connected to the network backbone directly, without an
NMEA 2000 drop cable.
Introduction
The Outboard Gateway (hereinafter Gateway or Device) is designed for petrol
engines without digital interfaces, and provides NMEA 2000 equipment with engine
revolutions (RPM), alternator voltage (measured at the NMEA 2000 interface) and
engine hours. It can also be programmed to use data from NMEA 2000 temperature
or pressure sensors and send these data as coolant and oil pressure or temperature,
boost or fuel pressure.
To connect the Gateway, you only need to connect it to the NMEA 2000 backbone,
make 3-5 turns of its wire around the spark plug wire, and afx the loops with tape.
In most cases, no additional settings are required, but you might need to set the RPM
divider according to the ignition system and type of your engine.
The Device can be programmed to issue high revolutions, high temperature and low
voltage warnings, and set the state of the charge indicator (displayed on MFD or NMEA
2000 display). If you have a single battery on your boat, the low voltage warning can
prevent the situation where a problem with the alternator or voltage regulator of your
engine is detected when the battery is already nearly dead.
The Gateway is equipped with a hidden button that allows changing the engine number
(0 - 3), RPM divider (from 0.5 to 8) and reseting the Device’s settings. These settings
are enough to install the Device.
To congure other settings, you need a PC gateway (from any manufacturer, including
our USB, Ethernet and Wi-Fi products) and software. The rmware of the Outboard
Gateway can only be updated from free CAN Log Viewer software (works on Microsoft
Windows, Linux and MacOS X) connected to NMEA 2000 with one of our NMEA
2000 gateways.
Thank you for purchasing our product and happy voyages!
— 4 —
Warranty and Technical Support
1. The Device warranty is valid for two years from the date of purchase. If a
Device was purchased in a retail store, the sale receipt may be requested when
applying for a warranty claim.
2. The Device warranty is terminated in case of violation of the instructions of this
Manual, case integrity breach, or repair or modication of the Device without
manufacturer’s written permission.
3. If a warranty request is accepted, the defective Device must be sent to the
manufacturer.
4. The warranty liabilities include repair and replacement of the goods and do not
include the cost of equipment installation and conguration, nor the shipping
of the defective Device to the manufacturer.
5. Responsibility of the manufacturer in case of any damage as a consequence of
Device operation or installation is limited to the Device cost.
6. The manufacturer is not responsible for any errors and inaccuracies in guides
and instructions of other companies.
7. The Device requires no maintenance. The Device’s case is non-dismountable.
In the event of a failure, please refer to Appendix A before contacting technical
support.
8. The manufacturer accepts applications under the warranty and provides
technical support only via e-mail or through authorized dealers.
9. Contact details of the manufacturer and a list of the authorized dealers are
published on the website: http://www.yachtd.com/
— 5 —
I. Specification
Figure 1. Drawing of YDOG-01R (at left) and YDOG-01N (at right) models of Device
Our devices are supplied with different types of NMEA 2000 connectors. Models
containing an «R» in the sufx of the model name are equipped with Raymarine
SeaTalk NG compatible connectors. Models containing «N» in the sufx are equipped
with NMEA 2000 Micro Male (DeviceNet) connectors which are used by Garmin and
other manufacturers.
— 6 —
Device parameter Value Unit
Supply voltage (from NMEA 2000 network) 9-16 V
Current consumption (from NMEA 2000 network) 30 mA
Load Equivalency Number 1 LEN
Pulse counting range (per minute) 200-70000 PPM
RPM (pulses) counting accuracy ±0.5 %
Voltage measurement accuracy ±0.05 V
Engine hours resolution 1 second
Operating temperature range -20 to +80 °C
Device case length (without connector) 40 mm
Wire length 2000 mm
Wire temperature range -50 to +180 °C
Weight 25 g
Yacht Devices Ltd declares that this product is compliant with the essential
requirements of EMC directive 2014/30/EU and radio and TTE directive
1999/5/EC.
Dispose of this product in accordance with the WEEE Directive. Do not mix
electronic waste with domestic or industrial refuse.
— 7 —
II. Device Installation and Connection to NMEA 2000
The Device requires no maintenance. When deciding where to install the Device,
choose a dry mounting location. Do not place the Device where it can be ooded by
water or exposed to rain or water spray. Please note that you may need to observe LED
signals and/or press the Gateway’s hidden button during the conguration procedure.
Figure 1. Bridging of two NMEA 2000 networks over Wi-Fi
— 8 —
If your outboard engine is big enough, the Device can be placed inside the engine.
Make sure that it is securely fastened, ventilated, isolated from hot surfaces and
protected from possible water, oil or petrol spray. If you have a problem with routing
the NMEA 2000 cable to the motor, you can place the Outboard Gateway and NMEA
2000 Wi-Fi Gateway YDWG-02 inside the motor, and power them from the ignition.
The data from the Wi-Fi Gateway can be accessed from any web browser or app. Or
you can install the second Wi-Fi Gateway inside your boat and the pair creates a Wi-Fi
bridge to virtually join NMEA 2000 the network inside your boat with the network
inside your engine.
The Device is powered from the NMEA 2000 interface and can be directly connected
to the NMEA 2000 network backbone without a drop cable. To connect the Device
to a Simrad SimNet network (with yellow connectors) you can use an adaptor cable
(SimNet Female — NMEA 2000 Micro Female, Navico part number 24006199).
Before connecting the Device, turn off the bus power supply. Refer to the manufacturer’s
documentation if you have any questions regarding the use of connectors:
• SeaTalk NG Reference Manual (81300-1) for Raymarine networks;
• Technical Reference for Garmin NMEA 2000 Products (190-00891-00) for
Garmin networks.
After connecting the Device, close the lock on the connector to secure and waterproof
it. After turning on the NMEA 2000 network power supply, the Device’s LED will start
ashing every 5 seconds, indicating that the Gateway is powered and functioning (see
Section IV for details).
Please note that you can’t directly connect the Device to NMEA 2000 port of your chart
plotter, the NMEA 2000 network requires a dedicated 12V power source.
— 9 —
III. Connection to the Engine and Initial Setup
The Device’s wire works like an antenna catching ignition impulses sent to a spark
plug. Usually you need to wrap the wire 3-5 times around the spark plug wire, and x
the loops with tape (we recommend a tape rated for automotive use). More turns make
the signal stronger, but it makes noise stronger too.
Figure 1. A – signal is good, B – signal is over amplied, C – signal is too weak.
Do not electrically connect Device’s wire.
— 10 —
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels Yacht Devices Porte
Manuels Porte populaires d'autres marques
LST
LST M500RFE-AS Manuel utilisateur
Kinnex
Kinnex Media Gateway Manuel utilisateur
2N Telekomunikace
2N Telekomunikace 2N StarGate Manuel utilisateur
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur
Telsey
Telsey CPVA 500 - SIP Manuel utilisateur
