Xylem YSI Pro1020 Manuel utilisateur

Pro1020

Quick Start Guide

Item #605188

This Quick Start Guide is meant to serve as a quick reference in calibrating and

operating the Pro1020. It is not intended to replace the information found in the User

Manual.

Getting Started

Unpack the instrument and install (2) C size batteries in the back of the instrument.

Tighten the four screws of the battery plate on to the back of the instrument.

Installing the DO Sensor

Prior to use, install the sensors into the cable assembly. Remove the temporary plastic

plugs from the cable’s ports by pulling them straight out of the port. Remove the plastic

plug from the sensor’s connector by pulling it straight off the sensor. Install the sensor

by inserting the sensor into the port and then hand tightening it. Do not use a tool and

do not over tighten. Install a pH, pH-ampliﬁed or ORP sensor in port 1 and a DO sensor

in port 2. Install a port plug into any port that does not have an installed sensor.

Enable the correct ISE (either pH or ORP) and Dissolved Oxygen (either galvanic - gray

sensor body or polarographic - black sensor body) sensor in the instrument’s System

Setup menu. Attach the cable assembly to your instrument.

Installing the DO Membrane

The DO sensor is shipped with a red protective cap to protect the electrode. A new

membrane cap must be installed before the ﬁrst use.

1. Prepare the O2 probe solution according to the instructions on the bottle. After

mixing, allow the solution to sit for 1 hour. This will help prevent air bubbles

from later developing under the membrane.

2. Remove, and discard or save the red protective cap.

3. Thoroughly rinse the sensor tip with distilled or deionized water.

4. Fill a new membrane cap with probe solution. Avoid touching the membrane

portion of the cap.

5. Thread the membrane cap onto the sensor, moderately tight. A small amount of

electrolyte will overﬂow.

pH Calibration

The Pro1020 pH sensor can be calibrated by performing a 1, 2 or 3-point calibration. At

least one of the calibration points must be done with pH buffer 7 or 6.86. For highest

accuracy, perform at least a 2-point calibration.

2 or 3-Point Calibration

1. Place the sensor in pH buffer 7 or 6.86 and allow the temperature and pH

readings to stabilize.

2. Press and hold Cal for three seconds.

3. Highlight pH and press Enter. If pH is not listed as an option, check the System

Setup menu to ensure pH is enabled in the ISE Sensor Type menu.

4. Highlight 2 point or 3 point and press enter.

5. If necessary, use the up and down arrow keys to adjust the pH buffer value.

6. Press Enter to continue to second point.

7. Rinse the sensor and place it in the second pH buffer (4/4.01 or 10/9.18). If

necessary, use the up and down arrow keys to adjust the pH buffer value.

8. Wait approximately 30 to 60 seconds for the pH sensor to stabilize and for the

temperature reading to stabilize.

9. Press Enter to either complete the 2-point calibration or to continue with the 3rd

calibration point. Or, press Cal to cancel.

10. If continuing on with a 3rd calibration point, rinse the sensor and place it in the

third pH buffer (4/4.01 or 10/9.18). If necessary, use the up and down arrow keys

to adjust the pH buffer value.

11. Wait approximately 30 to 60 seconds for the pH sensor to stabilize and for the

temperature reading to stabilize.

12. Press Enter to complete the 3-point calibration. Or, press Cal to cancel.

13. ‘Calibration Successful’ will display for a few seconds to indicate a successful

calibration and then the instrument will return to the Run screen.

14. If the calibration is unsuccessful, an error message will display on the screen.

Press the Cal key to exit the calibration error message and return to the Run

screen.

ORP Calibration

1. Place the clean sensor in ORP calibration solution. Wait for the ORP and

temperature readings to stabilize.

2. Press and hold Cal for three seconds.

3. Highlight ORP and press Enter. If ORP is not listed as an option, check the

System Setup menu to ensure ORP is enabled in the ISE Sensor Type menu.

4. Use the up and down arrow keys to adjust the ORP calibration solution value.

DO Calibration

The Pro1020 can be calibrated in % saturation, mg/L or ppm. Calibration of any option

(%, mg/L, or ppm) will automatically calibrate the others. The Pro1020 can be calibrated

with the press of a few keys when Quick DO Cal is enabled in the System Setup menu.

The following procedure outlines the % saturation calibration option with and without

Quick DO Cal enabled.

1. Moisten the sponge in the cal/transport sleeve with a small amount of water and

install it on the probe. Make sure the DO and temperature sensors are not

immersed in the water.

2. Turn the instrument on. If using a polarographic sensor, wait 10 minutes for the

DO sensor to stabilize. Galvanic sensors do not require a warm up time.

3. Ensure the barometer reading along the bottom of the display is accurate.

4. Press and hold the Cal key for three seconds.

5. If Quick DO Cal is enabled, highlight Dissolved Oxygen and press Enter. The

instrument will then indicate Calibrating %DO on the display and automatically

calibrate the sensor to the barometer reading.

Barometer Calibration

The barometer reading must be accurate to ensure accurate DO % calibrations and DO

readings. If the instrument’s barometer requires an adjustment, determine your local

barometric pressure (BP) from a barometer, an independent laboratory or from a local

weather service. If the BP reading has been corrected to sea level, use the following

equation to determine the true BP in mmHg for your altitude:

True BP = (Corrected BP in mmHg) – {2.5 * (Local Altitude in feet/100)}

1. From the Run screen, use the up or down arrow keys to highlight the barometer

box then press Enter.

2. Use the up or down arrow keys to adjust the barometer reading to the local, true

barometric pressure.

3. Press Enter to conﬁrm and save the barometer adjustment.

5. Wait for the temperature reading to stabilize, then press Enter to complete the

calibration or press Cal to cancel.

6. ‘Calibration Successful’ will display for a few seconds to indicate a successful

calibration and then the instrument will return to the Run screen.

7. If the calibration is unsuccessful, an error message will display on the screen.

Press the Cal key to exit the calibration error message and return to the Run

screen. Refer to the troubleshooting section of the manual for a possible

solution or contact YSI Technical Support.

Visit YSI.com/Pro1020 to ﬁnd the

User Manual, specs, and accessories.

Item# 605057 Dwg# 605188

December 2019 Rev B

1725 Brannum Lane

Yellow Springs, OH 45387

(800) 765-4974, (937) 767-7241

[email protected]

Taking Measurements

1. Before taking measurements, be sure the instrument has been calibrated to

ensure the most accurate readings.

2. Turn the instrument on and wait 5-15 minutes if using a polarographic sensor.

3. Install the sensor guard and then insert the probe into the sample.

4. Ensure the conductivity sensor is completely submerged in the sample. The two

holes near the cable should be covered by the sample for accurate conductivity

readings.

5. Move the probe in the sample at a rate of at least 6 inches (16 cm) per second if

using the yellow membrane and 3 inches (7.62 cm) per second if using the blue

membrane.

6. While continuing to provide sample movement, wait for the readings to

stabilize.

7. Highlight Save and press Enter to store the reading. The instrument will conﬁrm

that the reading was successfully saved.

Contact Information

6. If Quick DO Cal is not enabled, highlight %or %Local and press Enter. The

Pro1020 will display the current DO% and temperature readings along with

the % calibration value. Wait at least 3 seconds, then, once the DO% and

temperature readings are stable, press Enter to complete the calibration.

7. Calibration Successful will display for a few seconds to indicate a successful

calibration and then the instrument will return to the run screen.

8. If the calibration is unsuccessful, an error message will display on the screen.

Press the Cal key to exit the error message and return to the run screen.

Autres manuels pour YSI Pro1020

Table des matières

Autres manuels Xylem Instrument de mesure

Xylem

Xylem Sensus PulseRF-A3 Manuel utilisateur

Xylem

Xylem wtw pHotoFlex pH Manuel utilisateur

Xylem

Xylem WTW Cond 3310 Manuel utilisateur

Xylem

Xylem wtw inoLab Multi 9620 IDS Manuel utilisateur

Xylem

Xylem WTW Alyza IQ PO4 Manuel utilisateur

Xylem

Xylem OxiTop Control OC 100 Manuel utilisateur

Xylem

Xylem WTW Multi 3320 Manuel utilisateur

Xylem

Xylem WTW inoLab Multi 9630 IDS Manuel utilisateur

Xylem

Xylem sensus AutoRead Manuel utilisateur

Xylem

Xylem WTW Oxi 3310 Manuel utilisateur

Xylem

Xylem FLYGT Start 151 Manuel utilisateur

Xylem

Xylem ebro SSX 210 Manuel utilisateur

Xylem

Xylem WTW OxiTop-IDS Multi 3630 IDS Manuel utilisateur

Xylem

Xylem YSI Alyza IQ NH4 Manuel utilisateur

Xylem

Xylem Sensus Domo R Manuel de la liste des pièces

Xylem

Xylem WTW SensoLyt 900 Manuel utilisateur

Xylem

Xylem optimyze Manuel utilisateur

Xylem

Xylem ebro FOM 330 Manuel utilisateur

Xylem

Xylem wtw Br 800 DIN Manuel utilisateur

Xylem

Xylem SonTek RiverSurveyor Manuel utilisateur

Xylem

Xylem Sensus PulseRF HRI-A3 Manuel utilisateur

Xylem

Xylem Sensus iPERL MD 5000 Manuel utilisateur

Xylem

Xylem Sensus HRI-Mei Manuel utilisateur

Xylem

Xylem YSI ProQuatro Professional Series Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur