Xylem YSI Pro10 Manuel utilisateur

Pro10

Quick Start Guide

Item #605193

This Quick Start Guide is meant to serve as a quick reference in calibrating and

operating the Pro10. It is not intended to replace the information found in the User

Manual.

Getting Started

Unpack the instrument and install (2) C size batteries in the back of the instrument.

Tighten the four screws of the battery cover on to the back of the instrument.

Installing the Sensor

Prior to use, install either a pH or ORP sensor into the 60510 cable assembly. Remove

the temporary plastic plug from the cable’s port by pulling it straight out of the port.

Remove the plastic plug from the sensor’s connector by pulling it straight off the sensor.

Insert the sensor into the port so the o-rings on the sensor are no longer visible. Hand

tightening the sensor into place by twisting it clockwise. Do not use a tool and do not

over tighten

Enable the correct ISE (either pH or ORP) in the instrument’s System Setup menu. Attach

the cable assembly to your instrument.

pH Calibration

The Pro10 pH sensor can be calibrated by performing a 1, 2 or 3-point calibration. At

least one of the calibration points must be done with pH buffer 7 or 6.86. For highest

accuracy, perform at least a 2-point calibration.

2 or 3-Point Calibration

1. Place the sensor in pH buffer 7 or 6.86 and allow the temperature and pH

readings to stabilize.

2. Press and hold Cal for three seconds.

3. Highlight pH and press Enter. If pH is not listed as an option, check the System

Setup menu to ensure pH is enabled in the ISE Sensor Type menu.

4. Highlight 2 point or 3 point and press enter.

5. If necessary, use the up and down arrow keys to adjust the pH buffer value.

6. Press Enter to continue to second point.

ORP Calibration

1. Place the clean sensor in ORP calibration solution. Wait for the ORP and

temperature readings to stabilize.

2. Press and hold Cal for three seconds.

3. Highlight ORP and press Enter. If ORP is not listed as an option, check the

System Setup menu to ensure ORP is enabled in the ISE Sensor Type menu.

4. Use the up and down arrow keys to adjust the ORP calibration solution value.

5. Wait for the temperature reading to stabilize, then press Enter to complete the

calibration or press Cal to cancel.

6. ‘Calibration Successful’ will display for a few seconds to indicate a successful

calibration and then the instrument will return to the Run screen.

7. If the calibration is unsuccessful, an error message will display on the screen.

Press the Cal key to exit the calibration error message and return to the Run

screen. Refer to the troubleshooting section of the manual for a possible

solution or contact YSI Technical Support.

7. Rinse the sensor and place it in the second pH buffer (4/4.01 or 10/9.18). If

necessary, use the up and down arrow keys to adjust the pH buffer value.

8. Wait approximately 30 to 60 seconds for the pH sensor to stabilize and for the

temperature reading to stabilize.

9. Press Enter to either complete the 2-point calibration or to continue with the 3rd

calibration point. Or, press Cal to cancel.

10. If continuing on with a 3rd calibration point, rinse the sensor and place it in the

third pH buffer (4/4.01 or 10/9.18). If necessary, use the up and down arrow keys

to adjust the pH buffer value.

11. Wait approximately 30 to 60 seconds for the pH sensor to stabilize and for the

temperature reading to stabilize.

12. Press Enter to complete the 3-point calibration. Or, press Cal to cancel.

13. ‘Calibration Successful’ will display for a few seconds to indicate a successful

calibration and then the instrument will return to the Run screen.

14. If the calibration is unsuccessful, an error message will display on the screen.

Press the Cal key to exit the calibration error message and return to the Run

screen.

Visit YSI.com/Pro10 to ﬁnd the

User Manual, specs, and accessories.

Item# 605193 Dwg# 605193

December 2019 Rev B

1725 Brannum Lane

Yellow Springs, OH 45387

(800) 765-4974, (937) 767-7241

[email protected]

Taking Measurements

1. Before taking measurements, be sure the instrument has been calibrated to

ensure the most accurate readings.

2. Install the sensor guard and then insert the probe into the sample.

3. Highlight Save and press Enter to store the reading. The instrument will conﬁrm

the reading was successfully saved.

Contact Information

This page is intentionally left blank.

Table des matières

Autres manuels Xylem Instrument de mesure

Xylem

Xylem sunsus Domo R Manuel utilisateur

Xylem

Xylem WTW Cond 3210 Manuel utilisateur

Xylem

Xylem WTW LabStation LS Flex/430 Manuel utilisateur

Xylem

Xylem wtw Multi 3310 IDS Manuel utilisateur

Xylem

Xylem wtw NO 800 DIN Manuel utilisateur

Xylem

Xylem WTW Turb PLUS 2000 Manuel utilisateur

Xylem

Xylem YSI pH 1310P Manuel utilisateur

Xylem

Xylem wtw inoLab Multi 9620 IDS Manuel utilisateur

Xylem

Xylem optimyze Manuel utilisateur

Xylem

Xylem SI Analytics HandyLab 600 Manuel utilisateur

Xylem

Xylem WTW Turb 430 IR/T Manuel utilisateur

Xylem

Xylem WTW Turb 750 T Manuel utilisateur

Xylem

Xylem SENSUS PolluTherm Manuel utilisateur

Xylem

Xylem WTW pH/Cond 3320 Manuel utilisateur

Xylem

Xylem WTW OxiTop-i Manuel utilisateur

Xylem

Xylem Sensus PolluCom F/S C Manuel utilisateur

Xylem

Xylem WTW OxiTop-IDS Multi 3630 IDS Manuel utilisateur

Xylem

Xylem YSI pH/ISE 1320P Manuel utilisateur

Xylem

Xylem sensus DomoJet Manuel utilisateur

Xylem

Xylem ebro SSX 210 Manuel utilisateur

Xylem

Xylem WTW Multi 3430 Manuel utilisateur

Xylem

Xylem optimyze Manuel utilisateur

Xylem

Xylem Sensus PulseRF-A3 Manuel utilisateur

Xylem

Xylem SI Analytics Lab 865 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur