Xtreme XT300 Manuel utilisateur

X-TREME 4 WHEEL

ELECTRIC PERSONAL TRANSPORTER

Model XT300

Due to continuing improvements, actual product may differ slightly from the product described herein.

Visit our Web site at: http://www.x-tremescooters.com/

TO PREVENT SERIOUS INJURY, READ

AND UNDERSTAND ALL WARNINGS

AND INSTRUCTIONS BEFORE USE.

Page 1

PRODUCT SPECIFICATIONS

Item Description

Electrical Requirements Input power: AC90V-260V

Charge Time: 4-8 Hours

Output power: 36VDC

Battery Type:36VDC, 12AH, Lead Acid (Rechargeable)(Qly.3)

Motor Type:250 watt (Qty . 2)

Fuse Type: F30A110V-Batteries

F2A250V-Instrument panel and controls

Bulb Type: Turn Signals = YH/3W40V / Headlight=40Volt, 10 Watt

Power Cord Type: 18AWG×2C

Power Cord Plug Type:3-Prong power cable

Maximum Weight Capacity 250 Pounds

Maximum Speed Approximately 10 MPH (Depending On Weight Of Operator)

Maximum Travel Time

(On One Charge)

Approximately 15 Miles

Drive Type / Brake Type Belt Drive / Rear Wheel Disc

Wheel Types Front = 16”×2-1/8” Air tire (Qty.2)

Rear = 6”×1-1/4” Solid tire (Qty.2)

Overall Dimensions 50-3/4”H×23-1/2”W×28-1/2”L

Unit Weight 114 Pounds

Standard Features Forward & Reverse Modes / Foldable Handle / Key lgnition

Adjustable Height Handlebars / Headlight / Electric Horn

Front Facing Left & Right Turn Signals / Battery Indicator Gauge

Speed Indicator Gauge / LED Power & headlight Display / Battery Charger

Warning: This Scooter is not designed to be driven on roads. Streets., highways,

or other public roadways. Never operate the Scooter off-road or off-paved surfaces.

SAVE THIS MANUAL

You will need this manual for the safety warnings and precautions, assembly, operating,

inspection, maintenance and cleaning procedures, parts list and assembly diagram.

Keep your invoice with this manual. Write the invoice number on the inside of the front cover.

Keep this manual and invoice in a safe and dry place for future reference.

UNPACKING

When unpacking, check to make sure all the parts shown on the Parts Lists on pages 12

through 15 are included.

Page 2

1. This product is intended for adult use only. Do not allow children to ride on or play

with the XT-300.

2. IMPORTANT: Your insurance policies may not provide coverage for accidents involving

the use of this Scooter. To determine if coverage is provided, you should contact your

insurance company or agent.

3. Do not operate the Scooter in explosive atmospheres, such as in the presence of

flammable liquids, gases, or dust. Electrically powered products create sparks, which

may ignite the dust or fumes.

4. Keep bystanders, children, and visitors away while operating your XT-300.

Distractions can cause you to lose control.

5. Do not expose the Scooter to rain or wet conditions. Water entering electrically

powered products will increase the risk of electric shock.

6. Stay alert. Watch what you are doing, and use common sense when operating the

XT-300. Do not use this product while tired or under the influence of drugs, alcohol,

or medication. A moment of inattention while operating the XT-300 may result in serious

personal injury.

7. Never carry a passenger on the XT-300. This Scooter is designed for single rider only.

8. This Scooter is designed to be operated only on dry, flat, paved surfaces. Never

operate the XT-300 off-road. Never operate the XT-300 on roads, streets, highways, or

any other public roadways.

9. Always obey local laws and regulations for operating your XT-300.

10. The XT-300 is not designed for racing or performing tricks. Always ride responsibly.

11. DO not attempt to exceed the weight carrying capacity of 250Lbs.

12. Do not allow other adults to use the XT-300 without proper instructions.

13. Avoid accidental starting. Make sure the ignition Key is removed and the ignition is

off when not in use.

WARNING!

READ AND UNDERSTAND ALL INSTRUCTIONS

Failure to follow all instructions listed below may

result in

Electric shock, fire, and/or serious injury.

SAVE THESE INSTRUCTIONS

GENERAL SAFETY RULES

Page 3

14. Do not overreach. Keep proper footing and balance at all times. Proper footing and

balance enables better control in unexpected situations.

15. Do not use the XT-300 if the ignition Key does not turn it on or off. Any vehicle that

cannot be controlled with the ignition Switch is dangerous and must be replaced.

16. Make sure to remove all adjusting tools from the Scooter before starting. A wrench

or screwdriver that is left attached to a rotating part may result in personal injury and/or

product damage.

17. Maintain labels and nameplates. These carry important information.

18. Disconnect the charger from its power source and the XT-300 before making any

adjustments, changing accessories, or storing the unit. Such preventive safety

measures reduce the risk of starting the Scooter accidentally.

19. DO not abuse the charger. Never use the charger to pull the XT-300 or pull the

charger plug from any outlet. Keep the charger cord away from heat, oil, sharp

edges, or moving parts. Replace a damaged charger immediately. A damaged

Charger increases the risk of electric shock.

20. When operating the XT-300, always maintain a firm grip on the Handle Bars with

both hands to maintain control.

21. Do not over-stress the XT-300. This product will be easier and safer to ride at the speed

and capacity for which it was designed.

22. The charge time for the Battery is 5 hours. Do not charge the Battery for over 5 hours,

as damage to the Battery and/or XT-300 may result.

23. Always recharge the Battery when Scooter performance begins to diminish. Severe

heat is most destructive to a Battery. The more heat generated, the faster the Battery

loses its power. A Battery that gets too hot can be permanently damaged. Never

over-discharge a Battery by using the Scooter after Scooter performance has decreased.

Never attempt to discharge the Scooter’s Battery by continuing to operate the unit. When

performance begins to diminish, stop and recharge the Battery for optimal performance.

See p.8 “To Charge The Battery” for more information.

24. Battery leakage may occur under extreme usage or temperature conditions. If

Battery fluid comes in contact with skin, wash with soap and water and rinse with lemon

juice and vinegar. If the fluid comes into contact with eyes, flush with water for several

minutes and contact a physician immediately.

Page 4

25. Never burn a Battery, as it can explode in a fire. Contact local solid waste authorities

for instructions on correct disposal of a Battery.

26. Do not attempt to charge a leaking Battery.

27. Use only accessories that are recommended by X-Treme Scooters for your XT-300.

Accessories that may be suitable for one scooter may become hazardous when used on

another.

28. Store the XT-300 out of reach of children and other untrained persons. Electrically

powered products are dangerous in the hands of untrained users.

29. Maintain your XT-300 with care. Keep the unit clean and dry. Properly maintained

products are less likely to malfunction and are easier to control. Do not use the Scooter if

damaged.

30. Check for misalignment or binding of moving parts, breakage of parts, and any

other condition that may affect the Scooter’s operation. If damaged, have the

Scooter serviced before using. Many accidents are caused by poorly maintained

products.

31. Scooter service must be performed only by qualified repair personnel. Service or

maintenance performed by unqualified personnel could result in a risk of injury.

32. When servicing the Scooter, use only identical replacement parts. Follow

instructions in the “Inspection, Maintenance, And Cleaning” section of this manual.

Use of unauthorized parts or failure to follow maintenance instructions may create a risk of

electric shock or injury.

33. Never leave the Scooter unattended without first turning the lgnition to its “OFF”

position and removing the lgnition Key.

34. WARNING! People with pacemakers should consult their physician(s) before using

this product. Operation of electrical equipment in close proximity to a heart pacemaker

could cause interference to or failure of the pacemaker.

35. WARNING! The warnings and cautions discussed in this manual cannot cover all

possible conditions and situations that may occur. It must be understood by the operator

that common sense and caution are factors, which cannot be built into this product, but

must be supplied by the operator.

Page 5

ASSEMBLY AND OPERATING INSTRUCTIONS

1. CAUTION! Always make sure the ignition switch is in its “OFF” position and the

ignition Key is removed prior to setting up the XT-300, adding any accessories, or making

adjustments to the unit.

2. The Scooter comes fully assembled, but will require some setup as follows: The Steering

Bar Assembly must be positioned in place, the Wheels must be inflated and the Batteries

must be charged.

Raise, lock, And Adjust The Steering Bar Assembly:

1. Remove the Bolt illustrated below. (See Figure A.)

2. Lift the Steering Bar Assembly all the way up to its vertical position. Then, insert the Bolt

you removed previously back into the same hole and firmly tighten it. (See Figure A.)

3. Push the Quick Release Lever (C9) down to lock the Handle Bar in place. (See Figure A.)

4. To adjust the height of the Handle Bar, unlatch the Quick Release Lever (C9). Adjust the

Handle Bar to a comfortable height. Then, lock the Quick Release Lever (C9) in place.

(See Figure A.)

Install Power Pack Plug

1. Lay the XT-300 down so that you can locate the power pack plug under the scooter on the

left side.

2. Insert the plug into the power pack as show below.

3. Return the scooter to its upright position.

Page 6

Inflate The Wheels:

Make sure to inflate the front and back Wheels to 36 PSI.Do not exceed 36 PSI. Use

compressed air only.

Product Features:

Page 7

To Charge The Batteries:

1. Before riding the Scooter for the first time you must charge the Batteries. Thereafter, if

performance diminishes and/or the Voltage Gauge drops below 30V,you must

recharge the Batteries.

2. Make sure the lgnition is in the “OFF” position. (See Figure B.)

3. Plug the Charging Plug into the Scooter’s Power inlet Socket first, making sure to tighten

the ring of the Socket to hold the Charging Plug in place. Then, plug the 3-Prong Power

Cord Plug into the nearest 120 Volt, grounded, electrical outlet. (See Figure C.)

4. Charge the Scooter for 5 hours. A red LED light will illuminate on the Gauge Panel of the

Scooter while it is being charged. Once the Scooter is fully charged, the red LED Light will

automatically turn to green. Note: when the Voltage Gauge on the Gauge Panel indicates

42V-43V that also means a full charge. If the Voltage Gauge indicates lower than 30V, you

must charge the Batteries. (See Figures B and C.)

5. IMPORTANT: Do not charge the Scooter for more than 5 hours. Overcharging may limit

the life of the Scooter’s Batteries. Unplug after 5 hours to avoid overheating the Batteries.

Page 8

6. When the LED Light on the Gauge Panel turns to green, unplug the 3-Prong Power Cord

Plug from its electrical outlet. Then, unscrew the ring of the Scooter’s Power Inlet Socket

and disconnect the Charging Plug from the Socket. (See Figure C.)

Pre-operating Safety Checks:

1. Before operating the Scooter, make sure to perform the following safety checks:

A.Squeeze the Brake Handle, and push the Scooter to see if it rolls easily. If so, you will

need to tighten the Brakes. Each of the Rear Tires has its own Brake. To tighten, tilt the

Scooter forward to expose the undercarriage, and on either the Right or Left Rear Wheel,

loosen the Bolt on the Brake Arm that secures the Brake Cable. Next, while holding the

end of the Brake Cable, press down on the Brake Arm and Firmly retighten the Bolt

B.Repeat Step A. above on the other Brake. Upright the Scooter, and perform Brake Test

again by squeezing Brake Handle and pushing the Scooter.

2. While the Scooter is off,apply the Thumb Throttle and release. Check to make sure the

Throttle springs back to “stop” after you release it. (See Figure B.)

3. Check the Wheels (12, 24) for wear and proper air pressure (36 PSI).(See Assy. Diagram

on page 12.)

4. Check to make sure the Headlight, Turn Signal Lights, and Horn are working properly.

(See Figure B.)

Operating points:

1. WARNING: This Scooter is not designed to be driven on roads, streets, high ways, or

other public roadways. Never operate the Scooter off-road or off-paved surfaces.

2. Turn the lgnition Key to the “ON” position before starting the Scooter. (See Figure B.)

3. Apply the Thumb Throttle to move forward. Do not ride the Brakes. Release the Thumb

Throttle before braking. NOTE: The Scooter is equipped with an electrical braking system.

This means when you engage the Brakes, the Thumb Throttle is inoperative. (See Figure

B.)

4. The Scooter works best on level ground. Use caution while riding up inclines. Excess

climbing will limit the life of the Batteries and can be very dangerous.

5. Operate the Scooter only in good weather. Using the Scooter in rain or snow may result in

damage to the Scooter and/or personal injury to the operator.

6. Do not jump curbs, perform tricks, or ride on one Wheel.

7. Obey the laws in the city where you are riding the Scooter.

8. Do not leave the XT-300 in direct sunlight for an extended period of time.

Page 9

9. When finished riding the Scooter, gradually apply the Brakes until you come to a complete

stop. Then, turn the lgnition Key to its “OFF” position. (See Figure B.)

10. Make sure to remove the lgnition Key. Then, store the Scooter in a clean, dry location out

of reach of children.

INSPECTION, MAINTENANCE, AND CLEANING

1. WARNING! Make sure the lgnition of the Scooter is in its “OFF” position and the

Charging Plug is removed from the unit before performing any inspection, maintenance,

or cleaning procedures.

2. Before each use, inspect the general condition of the Scooter. Check for loose screws.

Misalignment or binding of moving parts, cracked or broken parts, and damaged electrical

wiring. Check the Thumb Throttle, Brakes, Wheels, Headlight, Turn Signals, Horn, and

any other condition that may affect its safe operation. If abnormal noise or vibration occurs,

have the problem corrected before further use. Do not use damaged equipment.

3. If stored for an extended period of time: Charge the Battery at least once every 90

days. To prolong the life of the Batter, discharge the Battery every 90 days. Only a

qualified service technician should replace the Battery.

4. To clean, use a clean, damp cloth and a mild detergent. Do not use solvents.Do not spray

water on the Scooter. Excessive exposure to water may damage the Scooter.

5. To replace the Instrument Panel Fuse: The Scooter uses an F2A250V Fuse which is

located on the Gauge Panel. If necessary, Unscrew and remove the Fuse Cap. Replace

the blown Fuse with a new Fuse. Then, replace the Fuse Cap. (See “Troubleshooting

“ section.)

6. To replace the Battery Fuse: The Scooter uses an F30A110V Fuse which is located

between the left side of Battery Case and the inside part of the Steel Frame. (See

“Troubleshooting “ section.)

7. CAUTION! All maintenance, service, or repairs not mentioned in this manual

must only be performed by a qualified service technician.

Page 10

Table des matières

Autres manuels Xtreme Scooter

Xtreme

Xtreme X-250 Manuel utilisateur

Xtreme

Xtreme X-400 Manuel utilisateur

Xtreme

Xtreme X-360 Manuel utilisateur

Xtreme

Xtreme XM-3150 Guide de dépannage

Xtreme

Xtreme XP-707 Manuel utilisateur

Xtreme

Xtreme XG-470 Manuel utilisateur

Xtreme

Xtreme XG-550 Manuel utilisateur

Xtreme

Xtreme XG-505 Manuel utilisateur

Xtreme

Xtreme XM-3100 Guide de dépannage

Xtreme

Xtreme X-10 Manuel utilisateur

Xtreme

Xtreme XB-420M Manuel utilisateur

Xtreme

Xtreme X-360 Manuel utilisateur

Xtreme

Xtreme X-370 Manuel utilisateur

Xtreme

Xtreme XR-101 Manuel utilisateur

Xtreme

Xtreme X-250 Manuel utilisateur

Xtreme

Xtreme X-600 Manuel utilisateur

Xtreme

Xtreme XM-3500Li Guide de dépannage

Xtreme

Xtreme X-360 Manuel utilisateur

Xtreme

Xtreme X-010 Manuel utilisateur

Xtreme

Xtreme X-560 Manuel utilisateur

Xtreme

Xtreme XR-301 Manuel utilisateur

Xtreme

Xtreme XM-4000Li Guide de dépannage

Xtreme

Xtreme XM-5000Li Guide de dépannage

Xtreme

Xtreme XB-420M Manuel utilisateur

Manuels Scooter populaires d'autres marques

TEKTRO

TEKTRO CHEETAH Manuel utilisateur

Douglas

Douglas Vespa Sprint Guide d'installation

PLAYTIVE

PLAYTIVE AS-2448 Manuel utilisateur

Ebinger

Ebinger DONKEY XL Manuel utilisateur

Flyer

Flyer Mountain Guide de l'utilisateur

BackCountry eBikes

BackCountry eBikes Storm Manuel utilisateur

equipmed

equipmed FreeRoam II Manuel utilisateur

Yoto

Yoto Lion Manuel utilisateur

WESTHILL BIKES

WESTHILL BIKES LINK Manuel utilisateur

BAnff

BAnff eProdigy series Manuel utilisateur

Winther

Winther 475 Manuel utilisateur

Jetson

Jetson JBZL17 Manuel utilisateur

First Choice Mobility

First Choice Mobility Roma Medical Corella S741 Manuel utilisateur

Carrera

Carrera impel Manuel utilisateur

Afikim

Afikim Superlight SL-3 Manuel utilisateur

CareCo

CareCo ZOOM Manuel utilisateur

Douglas

Douglas Vespa G.S. Manuel utilisateur

Gazelle

Gazelle with BOSCH System Manuel utilisateur