Xpresskit DBALL2 Manuel utilisateur

Installation Guide

Update Alert: Firmware updates are posted on the web on a regular basis. We recommend

that you check for firmware and/or install guide updates prior to installing this product.

SmartStart Compatible

SmartStart 200/250 Revision B is equipped with D2D, which means it can be connected to an interface module and

used in Remote Start Ready (RSR) mode without the use of a remote starter. See the Module Programming

section for more information.

Remote Start Ready (RSR) is a function that enables the interface module to remote start the vehicle completely

on its own. Consequently, there is no need for an aftermarket or an OEM remote starter in order to start the vehicle

from a distance.

® Volkswagen is a registered trademark and property of its respective company.

Vehicle Application Guide.....................................................................................................................................................................

Installation (Wiring Diagrams & Vehicle Wiring Reference Charts)

Type 1..................................................................................................................................................................................................

Type 2..................................................................................................................................................................................................

Type 3..................................................................................................................................................................................................

Type 4..................................................................................................................................................................................................

Immobilizer Interface............................................................................................................................................................................

Programming

SmartStart/XL202 Installation Notes....................................................................................................................................................

Module Programming...........................................................................................................................................................................

Module Reset.......................................................................................................................................................................................

Feature and Option List........................................................................................................................................................................

Feature Programming..........................................................................................................................................................................

LED Diagnostics & Troubleshooting....................................................................................................................................................

Parking Light Error Codes....................................................................................................................................................................

Limited One-Year Consumer Warranty................................................................................................................................................

Quick Reference Guide.......................................................................................................................................................................

Index

The installer must make sure the RFTD Output feature option is active in order to benefit from RSR. See the

Feature & Option List section for more information.

This guide supports the installation of a DBALL in Remote Start Ready (RSR) mode. This solution

offers three (3) configuration options to control your system: 3x OEM Lock Remote Start Activation,RF

Kit or SmartStart (both sold separately).

Refer to the Quick Reference Guide (QRG) at the end of this guide for more information on how to use

the various features offered with this product.

This firmware does not support transponder override. One (1) programmed OEM key must be wired

into the vehicle to complete installation of a remote starter.

During remote start sequence, the car console will indicate “no key located”. This is normal due to

the key wrapped in the installation. At vehicle takeover, the message will disappear.

Platform: DBALL2

Firmware: VW09 Remote Start Ready (RSR) Installation

Rev.: 20170420

Wire jump template

Vehicle Application Guide Page 2

Vehicles

2017

2016

2015

2014

2013

2012

2011

PK-Immobilizer Bypass-RFID Key Req'd

CC-Power Windows Rollup

DL-Arm Factory Security

DL-Disarm Factory Security

DL-Door Lock Control

DL-Door Unlock

DL-Driver Priority Unlock

RS-3x LOCK START (Start control using OEM Remote)

RS-3x LOCK STOP (Stop control using OEM Remote)

RS-RAP Shut Down (Retained ACC Power)

RS-Remote Start Ready

RS-SmartStart

RS-Tach / RPM Output

SS-Entry Monitoring ALL Door Pins

SS-Entry Monitoring Hood Pin

SS-Entry Monitoring Trunk/Hatch Pin

ST-Brake Status (foot brake)

ST-E-Brake Status

Volkswagen

EOS (Smart Key) 1 1 1 ••••••••••••••••••

Golf (Smart Key) 2 2 2 ••••••••••••••••••

GTI (Smart Key) 2 2 2 2 ••••••••••••••••••

Jetta (Smart Key) 3 3 3 4 4 4 4 ••••••••••••••••••

Jetta GLI (Smart Key) 1 1 1 1 ••••••••••••••••••

Passat (Smart Key) 1 1 1 1 1 ••••••••••••••••••

Tiguan (Smart Key) 1 1 1 ••••••••••••••••••

Legend: AV: Horn & Lights Controls

D: Data-to-Data (D2D) only CC: Comfort & Convenience Controls

•: D2D and Wire-to-Wire (W2W) DL: OE Door Lock & Alarm Controls

FOB: Sync CAN Interface w/ FOB Remote

PK: Transponder & Immobilizer Override

RS: Remote Start & Engine Controls

SS: Integrated Security & Monitoring

ST: Function/Feature Status

Note: Before attempting takeover, make sure all vehicle doors are closed.

Platform: DBALL2

Firmware: VW09 Remote Start Ready (RSR) Installation

Rev.: 20170420

Wire jump template

52 112441

42 1

VESCM

Driver side under dashboard

(+) Brake:

Black/Red,

pin 17

VESCM - conn. C

(brown 52-pin conn.)

Page 3

Installation Type 1

Important!

The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.

LED

14 12 2

Electronic Steering

Column Lock Module

(behind steering

column trim)

FT CAN Low: Orange/Brown, pin 15

FT CAN High: Orange/Green, pin 16

HS CAN Low:

Orange/Brown, pin 14

HS CAN High:

Orange/Black,

pin 6

FT CAN High: Orange/Green: 5

HS CAN High: Tan/Black: 3

FT CAN Low: Orange/Brown: 6

(+) Parking Light Output: Brown: 7

Parking Light Interrupt

(veh. side): Yellow: 8

Parking Light Interrupt

(conn. side): Orange/Yellow: 9

HS CAN Low: Tan: 4

(-) PTS Output: Green/Black: 2

(+) Brake Activation Output: Gray: 6

You can connect to either a XL202

RFTD OR a SmartStart module.

Refer to the SmartStart/XL202

Installation Notes for more

information.

6: White/Black: (-) Hood Input

(+) 12V Input: Red: 13

(-) Ground: Black: 14 Hood Pin

Remote Start Safety

Override Switch

Note: Hood pin only required

on vehicles not equipped

with a factory hood pin.

Prog. Button

DBALL2

OBDII

Diagnostic

Connector

(-) PTS 2: pin 4

Diode 1A

(-) PTS 1: pin 13

Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the ODBII diagnostic connector.

(-) Ground:

Brown, pin 4

(+) 12V:

Red/Yellow,

pin 16

[1] Key Wrap: Brown/Red: 12

[1] Key Wrap: Yellow/Red: 11

[1] Key Wrap: Orange/Red: 10

10 9 7 6

5 4 2 1

Parking Light

Interrupt:

pin 8

(+) Parking

Light: pin 3

Parking light conn.

(Black conn. at

parking light switch)

CUT

[1] For Key Wrap instructions refer to Immobilizer Interface section.

Platform: DBALL2

Firmware: VW09 Remote Start Ready (RSR) Installation

Rev.: 20170420

Wire jump template

Platform: DBALL2

Firmware: VW09 Remote Start Ready (RSR) Installation

Rev.: 20170420

Page 4

Vehicle Wiring Reference Chart - Type 1

Function Color Pin Polarity Location Color Pins

VW EOS (Smart key) 2013-2015

Parking Light Gray/Yellow 3 (+) Headlight Switch. Black 10

Parking Light Interupt Red/Blue or Red/White 8 cut Headlight Switch. Black 10

HS CAN High Orange/Black 6 Data OBDII. Black 16

HS CAN Low Orange/Brown 14 Data OBDII. Black 16

12V Red /Yellow 16 (+) OBDII. Black 16

FT CAN High Orange/Green 16 Data ESCLCM - Under steering column. White 16

FT CAN Low Orange/Brown 15 Data ESCLCM - Under steering column. White 16

PTS 1 Brown/Red 13 (-) ESCLCM - Under steering column. White 16

PTS 2 Brown/Blue 4 (-) ESCLCM - Under steering column. White 16

Brake Black/Red 17 (+) VESCM connector C. Brown 52

VW Jetta GLI (Smart key) 2012-2015

Parking Light White/Black or Gray/Yellow 3 (+) Headlight Switch. Black 10

Parking Light Interupt Red/White or Red/Green 8 cut Headlight Switch. Black 10

HS CAN High Orange/Black 6 Data OBDII. Black 16

HS CAN Low Orange/Brown 14 Data OBDII. Black 16

12V Red /Yellow 16 (+) OBDII. Black 16

FT CAN High Orange/Green 16 Data ESCLCM - Under steering column. Black 16

FT CAN Low Orange/Brown 15 Data ESCLCM - Under steering column. Black 16

PTS 1 Violet/Yellow 13 (-) ESCLCM - Under steering column. Black 16

PTS 2 Violet/Black 4 (-) ESCLCM - Under steering column. Black 16

Brake Black/Red 17 (+) VESCM connector C. Brown 52

VW Passat (Smart key) 2012-2016

Parking Light Gray/Yellow 3 (+) Headlight Switch. Black 10

Parking Light Interupt Red/Green 8 cut Headlight Switch. Black 10

HS CAN High Orange/Black 6 Data OBDII. Black 16

HS CAN Low Orange/Brown 14 Data OBDII. Black 16

12V Red /Yellow 16 (+) OBDII. Black 16

FT CAN High Orange/Green 16 Data ESCLCM - Under steering column. Black 16

FT CAN Low Orange/Brown 15 Data ESCLCM - Under steering column. Black 16

PTS 1 Violet/Yellow 13 (-) ESCLCM - Under steering column. Black 16

PTS 2 Violet/Black 4 (-) ESCLCM - Under steering column. Black 16

Brake Black/Red 17 (+) VESCM connector C. Black 52

VW Tiguan (Smart key) 2014-2016

Parking Light Gray/Yellow 3 (+) Headlight Switch. Black 10

Parking Light Interupt Red/Blue 8 cut Headlight Switch. Black 10

HS CAN High Orange/Black 6 Data OBDII. Black 16

HS CAN Low Orange/Brown 14 Data OBDII. Black 16

12V Red /Yellow 16 (+) OBDII. Black 16

FT CAN High Orange/Green 16 Data ESCLCM - Under steering column. Black 16

FT CAN Low Orange/Brown 15 Data ESCLCM - Under steering column. Black 16

PTS 1 Violet/Blue 13 (-) ESCLCM - Under steering column. Black 16

PTS 2 White/Violet 4 (-) ESCLCM - Under steering column. Black 16

Brake Black/Red 17 (+) VESCM connector C. Brown 52

Wire Information Connector Information

Wire jump template

52 112441

42 1

VESCM

Driver side under dashboard

(+) Brake:

Black/Red,

pin 17

VESCM - conn. C

(brown 52-pin conn.)

Page 5

Installation Type 2

Important!

The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.

(-) Ground

(+)12V

LED

14 12 2

Electronic Steering

Column Lock Module

(behind steering

column trim)

FT CAN Low: Orange/Brown, pin 15

FT CAN High: Orange/Green, pin 16

HS CAN Low:

Orange/Brown, pin 14

HS CAN High:

Orange/Black,

pin 6

FT CAN High: Orange/Green: 5

HS CAN High: Tan/Black: 3

FT CAN Low: Orange/Brown: 6

(+) Parking Light Output: Brown: 7

Parking Light Interrupt

(veh. side): Yellow: 8

Parking Light Interrupt

(conn. side): Orange/Yellow: 9

HS CAN Low: Tan: 4

(-) PTS Output: Green/Black: 2

(+) Brake Activation Output: Gray: 6

You can connect to either a XL202

RFTD OR a SmartStart module.

Refer to the SmartStart/XL202

Installation Notes for more

information.

6: White/Black: (-) Hood Input

(+) 12V Input: Red: 13

(-) Ground: Black: 14

Hood Pin

Remote Start Safety

Override Switch

Note: Hood pin only required

on vehicles not equipped

with a factory hood pin.

Prog. Button

DBALL2

OBDII

Diagnostic

Connector

(-) PTS 2: pin 4

Diode 1A

(-) PTS 1: pin 13

Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the ODBII diagnostic connector.

[1] For Key Wrap instructions refer to Immobilizer Interface section.

(-) Ground:

Brown, pin 4

(+) 12V:

Red/Yellow,

pin 16

[1] Key Wrap: Brown/Red: 12

[1] Key Wrap: Yellow/Red: 11

[1] Key Wrap: Orange/Red: 10

10 9 7 6

5 4 2 1

Parking Light

Interrupt:

Red/Blue or

Red/White, pin 8

(+) Parking Lights:

White/Black, pin 1

Parking light conn.

(Black conn. at

parking light switch)

CUT

Platform: DBALL2

Firmware: VW09 Remote Start Ready (RSR) Installation

Rev.: 20170420

Wire jump template

Platform: DBALL2

Firmware: VW09 Remote Start Ready (RSR) Installation

Rev.: 20170420

Vehicle Wiring Reference Chart - Type 2

Page 6

Function Color Pin Polarity Location Color Pins

VW Golf (Smart key) 2012-2014

Parking Light White/Black 1 (+) Headlight Switch. Black 10

Parking Light Interupt Red/Blue or Red/White 8 cut Headlight Switch. Black 10

HS CAN High Orange/Black 6 Data OBDII. Black 16

HS CAN Low Orange/Brown 14 Data OBDII. Black 16

12V Red /White 16 (+) OBDII. Black 16

FT CAN High Orange/Green 16 Data ESCLCM - Under steering column. Black 16

FT CAN Low Orange/Brown 15 Data ESCLCM - Under steering column. Black 16

PTS 1 Violet 13 (-) ESCLCM - Under steering column. Black 16

PTS 2 Violet/Blue 4 (-) ESCLCM - Under steering column. Black 16

Brake Black/Red 17 (+) VESCM connector C. Brown 52

VW GTI (Smart key) 2011-2014

Parking Light White/Black 1 (+) Headlight Switch. Black 10

Parking Light Interupt Red/Blue or Red/White 8 cut Headlight Switch. Black 10

HS CAN High Orange/Black 6 Data OBDII. Black 16

HS CAN Low Orange/Brown 14 Data OBDII. Black 16

12V Red /White 16 (+) OBDII. Black 16

FT CAN High Orange/Green 16 Data ESCLCM - Under steering column. Black 16

FT CAN Low Orange/Brown 15 Data ESCLCM - Under steering column. Black 16

PTS 1 Violet/Yellow 13 (-) ESCLCM - Under steering column. Black 16

PTS 2 Violet/Black 4 (-) ESCLCM - Under steering column. Black 16

Brake Black/Red 17 (+) VESCM connector C. Brown 52

Wire Information Connector Information

Wire jump template

Platform: DBALL2

Firmware: VW09 Remote Start Ready (RSR) Installation

Rev.: 20170420

Page 7

Installation Type 3

Important!

The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.

(-) Ground

(+)12V

LED

14 12 2

Electronic Steering Column

Lock Module (behind steering

column trim)

FT CAN Low: Orange/Brown, pin 15

FT CAN High: Orange/Green, pin 16

HS CAN Low:

Orange/Brown, pin 14

HS CAN High:

Orange/Black,

pin 6

FT CAN High: Orange/Green: 5

HS CAN High: Tan/Black: 3

FT CAN Low: Orange/Brown: 6

(+) Parking Light Output: Brown: 7

Parking Light Interrupt

(veh. side): Yellow: 8

Parking Light Interrupt

(conn. side): Orange/Yellow: 9

HS CAN Low: Tan: 4

(-) PTS Output: Green/Black: 2

(+) Brake Activation Output: Gray: 6

You can connect to either a XL202

RFTD OR a SmartStart module.

Refer to the SmartStart/XL202

Installation Notes for more

information.

6: White/Black: (-) Hood Input

(+) 12V Input: Red: 13

(-) Ground: Black: 14

Hood Pin

Remote Start Safety

Override Switch

Note: Hood pin only required

on vehicles not equipped

with a factory hood pin.

Prog. Button DBALL2

OBDII

Diagnostic

Connector

(-) PTS 2: Violet/Black,

pin 4

(-) PTS 1:

Violet/Yellow,

pin 13

[2] (MUX) OutputLock/Unlock : Violet/Brown: 9

[2] (-) Trunk Release Output: Blue/Red: 12

Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the ODBII diagnostic connector.

(-) Ground:

Brown, pin 4

(+) 12V:

Red/Yellow,

pin 16

[1] Key Wrap: Brown/Red: 12

[1] Key Wrap: Yellow/Red: 11

[1] Key Wrap: Orange/Red: 10

VESCM - Driver side under dashboard

A Plug (Black) at VESCM

[2] (-) Trunk Release: Violet, pin 23

[2] (MUX) Lock/Unlock:

Blue/Red, pin 24

(+) Brake: Black/Red, pin 43

10 9 7 6

5 4 2 1

Parking Light Interrupt:

Red/Yellow, pin 8

(+) Parking Light:

White/Black or Gray/Red, pin 3

CUT

Diode 1A

B Plug

White A Plug

Black

Parking light conn.

(Black conn. at

parking light switch)

[1] For Key Wrap instructions refer to Immobilizer Interface section.

[2] Locks and trunk release output ONLY required if door locks or trunk are not supported in data.

Wire jump template

Platform: DBALL2

Firmware: VW09 Remote Start Ready (RSR) Installation

Rev.: 20170420

Page 8

Vehicle Wiring Reference Chart - Type 3

Function Color Pin Polarity Location Color Pins

VW Jetta (Smart key) 2015-2017

Parking Light White/Black or Gray/Red 3 (+) Headlight Switch. Black 10

Parking Light Interupt Red/Yellow 8 cut Headlight Switch. Black 10

HS CAN High Orange/Black 6 Data OBDII. Black 16

HS CAN Low Orange/Brown 14 Data OBDII. Black 16

12V Red /White 16 (+) OBDII. Black 16

FT CAN High Orange/Green 16 Data ESCLCM - Under steering column. Black 16

FT CAN Low Orange/Brown 15 Data ESCLCM - Under steering column. Black 16

PTS 1 Violet/Yellow 13 (-) ESCLCM - Under steering column. Black 16

PTS 2 Violet/Black 4 (-) ESCLCM - Under steering column. Black 16

Brake Black/Red 43 (+) VESCM connector A. Black 73

Trunk Release Violet 23 (-) VESCM connector A. Black 73

Door Locks Blue/Red 24 MUX VESCM connector A. Black 73

Wire Information Connector Information

Wire jump template

Platform: DBALL2

Firmware: VW09 Remote Start Ready (RSR) Installation

Rev.: 20170420

Page 9

Installation Type 4

Important!

The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.

(-) Ground

(+)12V

LED

14 12 2

Electronic Steering Column

Lock Module (behind steering

column trim)

FT CAN Low: Orange/Brown, pin 15

FT CAN High: Orange/Green, pin 16

HS CAN Low:

Orange/Brown, pin 14

HS CAN High:

Orange/Black,

pin 6

FT CAN High: Orange/Green: 5

HS CAN High: Tan/Black: 3

FT CAN Low: Orange/Brown: 6

(+) Parking Light Output: Brown: 7

(+) 12V Input: Yellow: 8

HS CAN Low: Tan: 4

(-) PTS Output: Green/Black: 2

(+) Brake Activation Output: Gray: 6

You can connect to either a XL202

RFTD OR a SmartStart module.

Refer to the SmartStart/XL202

Installation Notes for more

information.

6: White/Black: (-) Hood Input

(+) 12V Input: Red: 13

(-) Ground: Black: 14

Hood Pin

Remote Start Safety

Override Switch

Note: Hood pin only required

on vehicles not equipped

with a factory hood pin.

Prog. Button DBALL2

OBDII

Diagnostic

Connector

(-) PTS 2: Violet/Black,

pin 4

(-) PTS 1:

Violet/Yellow,

pin 13

[2] (MUX) OutputLock/Unlock : Violet/Brown: 9

[2] (-) Trunk Release Output: Blue/Red: 12

Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the ODBII diagnostic connector.

[1] For Key Wrap instructions refer to pages 7 and 8.

(-) Ground:

Brown, pin 4

(+) 12V:

Red/Yellow,

pin 16

[1] Key Wrap: Brown/Red: 12

[1] Key Wrap: Yellow/Red: 11

[1] Key Wrap: Orange/Red: 10

VESCM - Driver side under dashboard

A Plug (Black) at VESCM

[2] (-) Trunk Release: Violet, pin 23

[2] Lock/Unlock: Blue/Red, pin 24

(+) Brake: Black/Red, pin 43

Diode 1A

B Plug

White A Plug

Black

(+) Parking Light:

White/Black or

Gray/Red, pin 14

Parking light conn.

(Black conn. at

parking light switch)

17 16 15 13 12 11 10

9 8 7 6 5 43 2 1

[2] Locks and trunk release output ONLY required if door locks or trunk are not supported in data.

Wire jump template

Platform: DBALL2

Firmware: VW09 Remote Start Ready (RSR) Installation

Rev.: 20170420

Function Color Pin Polarity Location Color Pins

VW Jetta (Smart key) 2011-2014

HS CAN High Orange/Black 6 Data OBDII. Black 16

HS CAN Low Orange/Brown 14 Data OBDII. Black 16

12V Red /White 16 (+) OBDII. Black 16

FT CAN High Orange/Green 16 Data ESCLCM - Under steering column. Black 16

FT CAN Low Orange/Brown 15 Data ESCLCM - Under steering column. Black 16

PTS 1 Violet/Yellow 13 (-) ESCLCM - Under steering column. Black 16

PTS 2 Violet/Black 4 (-) ESCLCM - Under steering column. Black 16

Parking Light White/Black or Gray/Red 14 (+) Headlight Switch. Black 17

Brake Black/Red 43 (+) VESCM connector A. Black 73

Trunk Release Violet 23 (-) VESCM connector A. Black 73

Door Locks Blue/Red 24 MUX VESCM connector A. Black 73

Wire Information Connector Information

Vehicle Wiring Reference Chart - Type 4

Page 10

Wire jump template

Autres manuels pour DBALL2

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Xpresskit Unité de contrôle

Xpresskit

Xpresskit DBALL2 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur