X-Rite RapidMatch GO Manuel utilisateur

User Guide

RapidMatchTMGO Spectrophotometer

Table of Contents

1. Packaging 5

2. Overview 5

3. Powering On 6

4. Charging the Battery 6

5. Measure Button 7

6. Contact Sensors, Indicators and LEDs 8

7. Home Screen8

8. Navigating the Screen 9

9. WiFi Mode 10

10. Settings Mode 10

11. Calibration 13

12. Measurement 14

13. Cleaning 17

14. Specifications 17

15. Troubleshooting 18

16. Service Information 20

17. Replacement Parts 20

Compliance Information

To view E label Compliance information for WiFi devices, choose Settings > Device

Information > Device Label

CE Declaration

Hereby, X-Rite, Incorporated, declares that this model is in compliance with the

essential requirements and other relevant provisions of Directive(s) EMC Directive

2014/30/EU, LVD 2014/35/EU and RoHS 2011/65/EU.

Models with WiFi:

CE Mark: Radio Equipment Directive (2014/53/EU) CE 1177

Zentri Module No. AMW106

CE Mark: Radio Equipment Directive (2014/53/EU) CE 1177

EN 300 328 V2.1.1

EMC : EN 301 489-1 V2.1.1, EN 301 489-17 V.3.1.1,

EN 55022:2010/AC:2011, EN 55024:2010

Health : EN 62311: 2008

Safety : EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013

Federal Communications Commission Notice

NOTE: This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are

RapidMatchTMGO Spectrophotometer

designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be required to correct the

interference at his own expense.

Models with WiFi:

Zentri Module No. AMW106

FCC ID: LSV-TOPAZ

RF Exposure requirements for mobile and base station transmission devices, a

separation distance of 20 cm or more should be maintained between the antenna

of this device and persons during operation. To ensure compliance, operation at

closer than this distance is not recommended. The antenna(s) used for this

transmitter must not be co-located or operating in conjunction with any other

antenna or transmitter.

NOTICE:

Changes or modifications made to this equipment not expressly approved by X-

Rite, Incorporated may void the FCC authorization to operate this equipment.

Industry Canada Compliance Statement

CAN ICES-3 (A) / NMB-3 (A)

Models with WiFi:

Zentri Module No. AMW106

IC ID: 20894-TOPAZ

RF Exposure requirements for mobile and base station transmission devices, a

separation distance of 20 cm or more should be maintained between the antenna

of this device and persons during operation. To ensure compliance, operation at

closer than this distance is not recommended. The antenna(s) used for this

transmitter must not be co-located or operating in conjunction with any other

antenna or transmitter.

NOTICE:

Changes or modifications made to this equipment not expressly approved by X-

Rite, Incorporated may void the FCC authorization to operate this equipment.

Modèles avec Wi-Fi :

Module Zentri n° AMW106

ID IC : 20894-TOPAZ

Exigences en matière d'exposition aux radiofréquences pour les appareils de

transmission (mobiles et stations de base) : une distance d'au moins 20 cm doit

être maintenue entre l'antenne de cet appareil et toute personne pendant le

fonctionnement. Afin d'assurer la conformité, il est déconseillé d'utiliser l'appareil à

une distance inférieure à celle-ci. La ou les antennes utilisées pour cet émetteur

ne doivent pas être installées ou utilisées conjointement avec d'autres antennes

ou émetteurs.

REMARQUE :

Les changements ou modifications apportés à cet équipement sans l'autorisation

expresse de X-Rite, Incorporated peuvent annuler l'autorisation d'utilisation de cet

équipement accordée par la FCC.

RapidMatchTMGO Spectrophotometer

Japanese Ministry of Internal Affairs and Communications (MIC)

Models with WiFi:

Zentri Module No. AMW106

Equipment Information

Use of this equipment in a manner other than that specified by X-Rite,

Incorporated may compromise design integrity and become unsafe.

To avoid discomfort, do not look directly into the measurement optics when the

instrument is on.

No user serviceable parts in this product.

WARNING: This instrument is not for use in explosive environments.

Do not immerse the instrument in liquid.

Transportation: This product contains a lithium-ion battery. Should you need to

ship this device, you may wish to consult published guidance documents by one or

more of these organizations for advice on how to comply with the regulations:

IATA, ICOA, IMDG & PHMSA. The battery contained in this device is 46g in

weight, 3.6V, 2.15 Ah, and complies with the UN 38.3 tests in effect the year it was

originally shipped.

The instrument is a sensitive measurement instrument. If the instrument

experiences a drop, a calibration should be performed followed by a selftest before

any measurements are taken to ensure the instrument is working properly. Refer

to the Calibration section for information on performing a Calibration.

Instructions for disposal: Please dispose of Waste Electrical and Electronic

Equipment (WEEE) at designated collection points for the recycling of such

equipment.

Firmware Software Licenses

1. Firmware consists of source code of:

Redistribution and use in source and binary forms, with or without modification, are

permitted provided that the following conditions are met:

- Redistributions of source code must retain the above copyright notice, this list of

conditions and the disclaimer below.

- Redistributions in binary form must reproduce the above copyright notice, this list

of conditions and the disclaimer below in the documentation and/or other materials

provided with the distribution.

RapidMatchTMGO Spectrophotometer

Atmel's name may not be used to endorse or promote products derived from this

software without specific prior written permission.

DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY

EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,

THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A

PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE DISCLAIMED. IN NO

EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,

SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT

NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;

LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)

HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN

CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR

OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,

EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

2. Acknowledgement:

Independent JPEG Group License

The Firmware uses source code under the IJG license

1. Packaging

•RapidMatch™GO instrument

•USB interface cabling

•Calibration reference

•Safety strap

•Screen protector

•Spare light seal

•Soft carrying case

•Docking station

2. Overview

Power on/off and

measure button

USB data

input/battery

charging

Indicator LED

Touch screen

Safety strap

connection

RapidMatchTMGO Spectrophotometer

3. Powering On

The power/measure button is used to initiate

the instrument from a power off state. Simply

press the button for about one second to turn

on the instrument. If the instrument does not

power up after pressing the power button, the

battery may require charging. Refer to

Charging the Battery section. The instrument

is also powered on by plugging the USB

cable into your computer’s USB port.

Powering Off

The instrument turns off automatically after two hours of nonuse. It is not

required to turn off the instrument manually.

When first powered up, the instrument goes through a startup procedure and

displays a splash screen before the Home screen appears.

Splash Screen Home Screen

4. Charging the Battery

General

The battery for your new instrument comes in a low to medium charge state

and should be charged before use.

Connect the USB cable to the instrument and your computer’s USB port.

Make sure that the USB cable is connected directly to the computer. A

connection to a USB port of a keyboard or PC monitor or a bus-powered USB

hub is not recommended. PC monitor or keyboard USB ports are low power

USB ports.

Power/measure

button

USB cable

RapidMatchTMGO Spectrophotometer

During charging, the instrument switches on and indicates charging with a

“lightning bolt” in the battery icon. The instrument will not power completely

off while plugged into the computer USB port, however, it will go into standby

mode. This is indicated by a blue pulsing LED.

A full charge from empty will take approximately 6 hours connected to a

computer USB port. Alternatively a standard USB charger can be used.

The charging time will not be reduced with a standard USB charger.

A USB charger with at least 500 mA is required. A standard charger with 1 A

will not charge any faster.

Battery Icon Information

This icon at the top of the screen would indicate the

battery is fully charged.

This icon at the top of the screen would indicate the

battery has a sufficient charge for a substantial number

of measurements.

This icon at the top of the screen would indicate the

battery pack is low, but measurements are still possible.

Battery should be charged soon.

The “lightning bolt” in the center of the icon at the top of

the screen indicates the battery is charging.

Battery status is also reported in the Device Information menu item of the

Settings window.

5. Measure Button

The measure button (1) is located on the side of the instrument. This is the

same button that is used to power on and off the instrument. You can also tap

the center of the screen (2) to initiate a measurement.

NOTE: In case of a firmware crash, this button acts as a RESET button.

Remove the USB cable, press and hold the button for 10 seconds and then

release. The instrument will turn off. Refer to the Troubleshooting section for

additional information.

(1)

(2)

RapidMatchTMGO Spectrophotometer

6. Contact Sensors, Indicators and LEDs

The indicators in the screen are arranged in the same pattern as the contact

sensors located around the measurement port.

•Green Indicator: ideal contact is being applied to the corresponding

sensor. A measurement can be taken when all three indicators illuminate

green.

•Red Indicator: the required contact is not being applied to the

corresponding sensor. Correct contact must be applied to achieve a

green indicator condition.

The multi-color LED located on the front of instrument provides visual

feedback on the status of a measurement and contact sensors.

•Green LED: Indicates all three contact sensors are activated properly

and a measurement can now be triggered.

•Red LED: Indicates one or more of the contact sensors is not properly

activated or an error has occurred during a measurement.

•Blue Pulsing LED: Indicates the instrument is in standby mode with the

USB cable plugged into the computer and charging.

•Off: Indicates the instrument is off and not ready to measure.

7. Home Screen

When the instrument is powered-up, the home (top level) screen appears

after the startup procedure is complete. Select the modes by tapping the

icons located on the display screen.

Contact sensor

indicator

LEDs

Contact sensor

indicator

Contact sensor

indicator

RapidMatchTMGO Spectrophotometer

Job List Mode:This mode is the main mode of operation. Jobs are added,

selected, deleted, and measurements are taken in this mode.

Settings Mode:The settings mode is used to set and edit the instruments

configuration options, and to enter the calibration mode. The settings options

should be reviewed before you use your instrument for the first time.

Connect WiFi:This icon is used to connect to WiFi network. Refer to WiFi

mode section for information.

Header Bar:Displays the current mode, WiFi connection (where applicable),

and battery life status.

8. Navigating the Screen

The instrument features a graphical touch screen display. All functionality is

accessed directly through the screen.

Scrolling through Settings and Jobs

The Up (▲) and Down (▼) arrows appears on screens when some settings

or jobs cannot be accessed from the main view. You can also swipe the

screen up or down to view the additional settings and jobs.

The Left (◄) arrow at the bottom of the screen is used to return the screen to

the previous view.

Connect WiFi

Settings mode

Job List mode

Header bar

RapidMatchTMGO Spectrophotometer

Opening Settings and Jobs

Settings and jobs are accessed by tapping the corresponding icon on the

Home screen. For this example, the Settings icon was tapped to open the

Settings screen. See Settings Mode descriptions that follow.

9. WiFi Mode

The WiFi Mode is used to connect to the available networks when activated

in the Settings mode.

1. From the Home screen, tap the Connect icon to access the WiFi

screen.

2. The instrument will search for available networks. Available networks for

connection appear with a green checkmark next to the name.

3. Tap the screen to open the Job Viewer screen.

4. Tap the Settings icon to view the WiFi Settings for the connected

network.

5. Tap the Left (◄) arrow to return to the home screen.

10. Settings Mode

Settings mode is used to adjust and view the instrument’s settings.

Calibration

This option is used to activate the calibration procedure.

bars

Connected to WiFi

network

Customer application

disconnected

WiFi details

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels X-Rite Instrument de mesure

X-Rite

X-Rite MA94 Manuel utilisateur

X-Rite

X-Rite 552 Manuel utilisateur

X-Rite

X-Rite i1 Display Pro Manuel utilisateur

X-Rite

X-Rite i1Pro Manuel utilisateur

X-Rite

X-Rite Ci51 Manuel utilisateur

X-Rite

X-Rite EyeOne Pro Manuel utilisateur

X-Rite

X-Rite ATD Manuel utilisateur

X-Rite

X-Rite 962 Manuel utilisateur

X-Rite

X-Rite Ci7860 Series Manuel utilisateur

X-Rite

X-Rite DensiEye 100 Manuel utilisateur

X-Rite

X-Rite iCPlate2 Manuel utilisateur

X-Rite

X-Rite PANTONE i1 PRO 3 PLUS Manuel utilisateur

X-Rite

X-Rite 500 Series Manuel utilisateur

X-Rite

X-Rite Color i7 Manuel utilisateur

X-Rite

X-Rite BASF 12/6 Manuel utilisateur

X-Rite

X-Rite RapidMatch XI Manuel utilisateur

X-Rite

X-Rite SP52 Manuel utilisateur

X-Rite

X-Rite DigiMatch PPG Manuel utilisateur

X-Rite

X-Rite X-RiteColor DTP34 Manuel utilisateur

X-Rite

X-Rite RM200QC Manuel utilisateur

X-Rite

X-Rite 891 Manuel utilisateur

X-Rite

X-Rite AutoScan DTP41 Series Manuel utilisateur

X-Rite

X-Rite RM61 Manuel utilisateur

X-Rite

X-Rite PANTONE i1 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur