Workhorse ODYSSEY O4400F Manuel utilisateur
Owner’s Manual
ODYSSEY FLOOR MODEL
3730 E. Southern Avenue, Phoenix, AZ 85040 USA
800-778-8779 Workhorseproducts.com 1
O-6400-F shown
67-1455 rev 118
Table of Contents
3730 E. Southern Avenue, Phoenix, AZ 85040 USA
800-778-8779 Workhorseproducts.com 2
I. Introducon & Safety Informaon……………………………………….…………………………………3
II. Specicaons …………………………………………………………………………………………………………4
III. Parts for Assembly………………………………………………………………………………………………….5
IV. Disassembling Press for Small Entryways………………………………………………………………..7
V. Assembly
Step 1: Installing the Spring Assemblies……………………………………………………………..8
Step 2: Installing the Pallet Arms………………………………………………………………………10
Step 3: Installing the Pallets…………………………………………………………………………..…11
Step 4: Leveling the Press…………………………………………………………………………………12
V. Print Head and Micro Adjustments……………………………………………………………………….14
VI. Maintenance and Troubleshoong……………………………………………………………………….17
VII. Limited Warranty…………………………………………………………………………………………………19
Introducon & Safety
3730 E. Southern Avenue, Phoenix, AZ 85040 USA
800-778-8779 Workhorseproducts.com 3
Congratulaons on your purchase of the Odyssey Manual Prinng Press. We’d like to thank
you for choosing Workhorse Products!
Please check the contents of the packaging for damages immediately. While our packaging has been
designed to handle normal shipping condions, we cannot foresee damages caused by the carrier and are
not responsible for damages that occur during transportaon.
If shipping damage has occurred, immediately contact the carrier to le a claim and contact Workhorse
Products at 800-778-8779.
The Importance of the Owner’s Manual:
The purpose of the Owner’s Manual is to familiarize you with the parts and operaons of the Odyssey Floor
Model. There are step-by-step instrucons to assemble the press as well as troubleshoong informaon.
Also included are explanaons of the product’s key features and addional informaon that will help with
the maintenance of your press.
Safety
The Odyssey Manual Prinng Press is intended to be used for manual screen prinng of texles.
To avoid damage or injury, please be sure to use only for the purpose it was designed for.
Anybody operang the press should rst read through this owner’s manual to ensure a full
understanding of how to properly use and maintain the Odyssey.
Do not sit, stand, or apply excess weight on press.
Do not place foreign objects on press.
Be sure print heads are in their upright posion when installing and removing screens.
Keep small children and pets out of reach of the press.
Be sure the area around the press is free of cluer, spills, or debris.
Specicaons
3730 E. Southern Avenue, Phoenix, AZ 85040 USA
800-778-8779 Workhorseproducts.com 4
4 Color, 4 Staon
Max Screen: 44" (112 cm)
Dimensions: 90” x 34-36” (229 cm x 86-91 cm)
O4400F
6 Color, 4 Staon
Max Screen: 25" (64 cm)
Dimensions: 90” x 34-36” (229 cm x 86-91 cm)
O6400F
3730 E. Southern Avenue, Phoenix, AZ 85040 USA
800-778-8779 Workhorseproducts.com 5
QTY
O-4400F
QTY
O-6400-F
PART NUMBER DESCRIPTIONITEM #
11OD-44–MP or OD-64-MP MAIN ASSEMBLY (AS SHIPPED)1
4621016 SPRING PACKS2
4421017 PALLET ARMS3
4475-20-1618 PALLETS 16 X 18 4
4641-HB-M10-60 HEX BOLTS5
4642-NYL-M10-10 NYLON LOCK NUTS6
812 43-FIT-M10-10 FLAT WASHERS7
16 16 41-HTB-3125-15 HEX TAP BOLTS8
16 16 43-LOK-3125-20 LOCK WASHERS9
Parts for Assembly
*Quanty of parts depends on model purchased. Reference your Model Number in table above for correct quanty of parts.
5
9
8
2
6
7
O-6400-F shown
1
3
4
Parts for Assembly
3730 E. Southern Avenue, Phoenix, AZ 85040 USA
800-778-8779 Workhorseproducts.com 6
The Odyssey is shipped parally disassembled to prevent damage to unit during transportaon.
O-4400-FO-6400-F
FULLY ASSEMBLED FULLY ASSEMBLED
Order of Assembly:
1. Installaon of spring packs in swing arms
2. Aaching pallet arms to lower wheel
3. Aaching pallets to pallet arms
4. Leveling unit
All parts are labeled on page 5 and will be referred to in the following steps. Any parts and
tools that are necessary for assembly will be listed on each step. Please be sure you are
using the correct tools and parts to assemble your press.
Breaking Down for Small Entryway
3730 E. Southern Avenue, Phoenix, AZ 85040 USA
800-778-8779 Workhorseproducts.com 7
In some circumstances, it may be necessary to disassemble the press to t through a small
entryway. If you are having diculty moving your press through a small door or entryway,
follow these simple instrucons, otherwise turn to page 8.
1. Take a wrench and remove the bolt that sits on
top of the cap on the upper carousel wheel. Li
cap o to expose center sha.
2. Li the upper carousel wheel o of the center
sha. Set aside and remove the lower wheel o
of the center sha as well.
3. Odyssey should be in 3 smaller pieces and will
now easily t through a small doorway.
4. Once through the door, return the lower wheel
and the upper wheel back on the center sha.
Place the cap on top of the upper wheel and
secure the bolt in place with a wrench.
Assembly
3730 E. Southern Avenue, Phoenix, AZ 85040 USA
800-778-8779 Workhorseproducts.com 8
Step 1: Installing the Springs PARTS NEEDED TOOLS NEEDED
SPRING PACKS (Item #2) 13 MM WRENCH
HEX BOLTS (Item #5)
FLAT WASHERS (Item #7)
NYLON LOCK NUTS (Item #6)
1. Li up swing arm and locate empty
grooves on the boom of the swing
arm. Place boom of spring assembly
into grooves as shown, then insert
the top of the spring pack into the top
grooves.
2. While Spring Pack is resng in place,
lower swing arm onto top of spring
assembly.
3. Aer installing spring assembly, push
swing arm down and hold in place.
*quanty of parts depends on model being assembled
TOP OF SPRING
ASSEMBLY
BOTTOM OF SPRING
ASSEMBLY
Grooves for
Spring Pack
Push down
Assembly
3730 E. Southern Avenue, Phoenix, AZ 85040 USA
800-778-8779 Workhorseproducts.com 9
Step 1: Installing the Springs PARTS NEEDED TOOLS NEEDED
HEX BOLTS (Item #5) 13 MM WRENCH
FLAT WASHERS (Item #7)
NYLON LOCK NUTS (Item #6)
4. Install hex bolt with one washer from
the side of swing arm.
5. Carefully release swing arm unl it
rests against the hex bolt.
6. Install nylon lock nut and washer on
other side of bolt. Tighten with
wrench.
7. Repeat with all swing arms.
*quanty of parts depends on model being assembled
7
75
6
Assembly
3730 E. Southern Avenue, Phoenix, AZ 85040 USA
800-778-8779 Workhorseproducts.com 10
Step 2: Installing the Pallet Arms PARTS NEEDED TOOLS NEEDED
PALLET ARMS (Item #3) 1/2” WRENCH
HEX TAP BOLTS (Item #8)
LOCK WASHERS (item #9)
*quanty of parts depends on model being assembled
1. Match up number on pallet arm to
number on lower wheel bracket. Place
pallet arm into the lower wheel bracket.
Line up pre-drilled holes on pallet arm
to pre-drilled holes on the boom of
bracket.
2. Locate pre-drilled holes at the boom
of the bracket and use four hex tap
bolts and four lock washers to secure
one pallet arm into place. Tighten bolts
using 1/2” wrench.
3. Repeat for each addional arm.
**Do NOT use hex nuts to hold in place or
you could bend the pallet arm.**
8
9
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Workhorse Outils électriques
