Wolf ICBDD30 Manuel utilisateur

DOWNDRAFT VENTILATION

INSTALLATION INSTRUCTIONS

INSTRUCCIONES DE INSTALACIÓN

INSTRUCTIONS D’INSTALLATION

ISTRUZIONI PER L’INSTALLAZIONE

INSTALLATIONSANWEISUNGEN

ENGLISH 4

ESPÃNOL 18

FRANÇAIS 32

ITALIANO 46

DEUTSCH 60

As you follow these instructions, you will

notice WARNING and CAUTION symbols.

This blocked information is important for the

safe and efficient installation of Wolf equip-

ment. There are two types of potential

hazards that may occur during installation.

Another footnote we would like to identify is

IMPORTANT NOTE: This highlights informa-

tion that is especially relevant to a problem-

free installation.

signals a situation where minor injury or

product damage may occur if you do not

follow instructions.

states a hazard that may cause serious

injury or death if precautions are not

followed.

WOLF

is a registered trademark of Wolf Appliance, Inc.

CONTACT

INFORMATION

Website:

wolfappliance.com

INSTALLATION REQUIREMENTS

IMPORTANT NOTE:

This installation must be

completed by a qualified installer or Wolf

authorized service center technician.

Installer:

Please read the entire Installation

Instructions prior to installation. Save these

instructions for the local inspector’s refer-

ence, then leave them with the homeowner.

Homeowner:

Please read and keep these

instructions for future reference and be sure

to read the entire Use & Care Information

prior to use.

Any questions or problems regarding the

installation should be directed to your dealer

or visit our website, wolfappliance.com.

IMPORTANT NOTE:

This appliance must be

installed in accordance with National Electrical

Codes, as well as all state, municipal and local

codes. The correct voltage, frequency and

amperage must be supplied to the appliance

from a dedicated, grounded circuit which is

protected by a properly sized circuit breaker or

time delay fuse. The proper voltage, frequency,

and amperage ratings are listed on the product

rating plate.

Record the model and serial numbers before

installing the downdraft ventilation system.

Both numbers are listed on the rating plate,

located above the airbox on the front side of

the unit. Refer to the illustration below.

BEFORE YOU START

Proper installation is the responsibility of

the installer.

Check with local utilities for electrical codes

that apply in your area. Local codes vary.

Installation, electrical connections and

grounding must comply with applicable

codes.

This appliance must be properly grounded.

Refer to Electrical Requirements on

page 7.

Make sure you have the tools and materials

necessary for proper installation.

Any required service must be performed by

a Wolf authorized service center. Wolf is not

responsible for service required to correct a

faulty installation.

WOLF DOWNDRAFT VENTILATION SYSTEMS

RATING PLATE

INFORMATION

Model Number

Serial Number

Rating plate location

Location of

rating plate

(behind filters)

OVERALL DIMENSIONS

MODELS ICBDD30I AND ICBDD30R

Overall Width 762 mm

Width of Chimney 667 mm

Overall Height

(above countertop)

230 mm

Overall Depth 60 mm

Depth of Chimney 38 mm

MODELS ICBDD36I AND ICBDD36R

Overall Width 914 mm

Width of Chimney 819 mm

Overall Height

(above countertop)

230 mm

Overall Depth 60 mm

Depth of Chimney 38 mm

WOLF DOWNDRAFT VENTILATION SYSTEMS

DOWNDRAFT VENTILATION

IMPORTANT NOTE:

Wolf downdraft ventila-

tion systems are recommended for use with

Wolf framed induction or electric, gas and

multi-function cooktops. They cannot be used

with unframed induction or electric cooktops

and are not recommended for use with the

electric grill, steamer and fryer modules.

A Pro ventilation hood is recommended for

use with Wolf dual fuel ranges, gas ranges

and rangetops.

IMPORTANT NOTE:

A downdraft can be

used with sealed burner rangetop Models

ICBSRT304 and ICBSRT366. An accessory trim

kit (810215) is necessary for this installation.

Contact your Wolf dealer for details.

Wolf downdraft ventilation systems are

available in 762 mm, 914 mm and 1156 mm

widths. The downdraft should be at least as

wide as the cooktop.

Models ICBDD30I, ICBDD36I and ICBDD45I

include an 850 m3/hr internal blower. Models

ICBDD30R, ICBDD36R and ICBDD45R are

shipped without a blower assembly and can

be used with a 1529 m3/hr remote blower

(812307), available through your Wolf dealer.

Models ICBDD30I and ICBDD30R

60 mm

762 mm

230 mm 667 mm

38 mm

DEPTH OF

DOWNDRAFT CHIMNEY

914 mm

819 mm

60 mm

230 mm

38 mm

DEPTH OF

DOWNDRAFT CHIMNEY

Models ICBDD36I and ICBDD36R

Model ICBDD30

Model ICBDD36

Model ICBDD45

Dimensions may vary to +

– 3 mm.

INSTALLATION INSTRUCTIONS

Models ICBDD45I and ICBDD45R

1156 mm

1048 mm

60 mm

230 mm

38 mm

DEPTH OF

DOWNDRAFT CHIMNEY

ELECTRICAL REQUIREMENTS

Wolf downdraft ventilation systems require a

separate, 240 V 50/60 Hz power supply. The

service should have its own 10A circuit

breaker. The unit is supplied with a 2.5 m CEE

7/7 “Schuko” style Continental European

power cord. The specific location of the outlet

is not critical, as long as it is within reach of

the power cord that is located mid-way, top

and bottom, on the right side of the downdraft.

IMPORTANT NOTE:

If Model ICBDD30 is to be

installed in a 762 mm wide cabinet, Model

ICBDD36 in a 914 mm wide cabinet or Model

ICBDD45 in a 1156 mm wide cabinet, the

electrical outlet cannot be located on the back

wall of the cabinet. The outlet can be placed in

an adjacent cabinet within reach of the power

cord. An access hole for the power cord must

be drilled in the cabinet wall.

Choose the electrical location shown in

the illustration below that best suits your

installation.

Location of electrical

914 mm min

FOR MODEL ICBDD36

1156 mm min

FOR MODEL ICBDD45

762 mm min

FOR MODEL ICBDD30

OPTIONAL

ELECTRICAL

LOCATION IN

ADJACENT RIGHT

SIDE CABINET

OVERALL DIMENSIONS

MODELS ICBDD45I AND ICBDD45R

Overall Width 1156 mm

Width of Chimney 1048 mm

Overall Height

(above countertop)

230 mm

Overall Depth 60 mm

Depth of Chimney 38 mm

Dimensions may vary to +

–3 mm.

IMPORTANT

NOTE

You must follow

all National

Electrical Code

regulations. In

addition, be aware

of local codes and

ordinances when

installing your

service.

INSTALLATION SPECIFICATIONS

Wolf downdraft Model ICBDD30 will fit most

762 mm wide cabinets, Model ICBDD36 will fit

most 914 mm wide cabinets and Model

ICBDD45 will fit most 1156 mm wide cabinets.

It is recommended that oversized cabinets be

used for easier installation. Cabinet backs may

need to be removed.

Wolf downdraft ventilation systems can be

mounted in an island, peninsula or standard

wall location.

The illustration below provides installation

dimensions for all Wolf downdraft models.

Pay careful attention to the areas of potential

interference as noted in the illustration.

IMPORTANT NOTE:

To install a downdraft

system and a Wolf cooktop, you must allow for

a minimum 638 mm flat counter space from

front to back. A countertop with a raised lip or

backsplash may not allow enough space for

proper installation. 60 mm of flat countertop is

required behind the cooktop and 44 mm is

necessary between the back edge of the

cooktop and inside of cabinet back.

If downdraft Model ICBDD30 is installed in

combination with with two cooktops or inte-

grated modules, an integrated module support

(8603386) for downdraft ventilation is required.

The integrated module support is not required

for Model ICBDD45.

WOLF DOWNDRAFT VENTILATION SYSTEMS

54 mm

489 mm

COOKTOP CUT-OUT

DEPTH

914 mm

60 mm

638 mm min

OF FLAT COUNTERTOP*

8.7 mm

745 mm

COUNTERTOP

TO BOTTOM OF

AIR BOX

457

83 mm

127

197 mm

16 mm 64 mm min

WITH NO

RAISED LIP*

*AREAS OF POTENTIAL INTERFERENCE

610 mm min

CABINET DEPTH

44 mm min

BACK EDGE

OF COOKTOP

TO INSIDE OF

CABINET BACK*

181 mm

Downdraft installation dimensions

INSTALLATION INSTRUCTIONS

INSTALLATION SPECIFICATIONS

For installation of a downdraft system with a

cooktop, refer to the cooktop installation

instructions for the dimensions of the cooktop,

countertop cut-out and cabinet requirements.

The depth of the cooktop may vary and will

affect the location of the downdraft in the

countertop.

The illustration below provides countertop

cut-out dimensions for downdraft Models

ICBDD30, ICBDD36 and ICBDD45 installed with

a Wolf 762 mm or 914 mm cooktop or combi-

nation of cooktop and/or modules.

IMPORTANT NOTE:

For installation of a

downdraft with sealed burner rangetop

Models ICBSRT304 and ICBSRT366, an acces-

sory trim kit (810215) is necessary. Contact

your Wolf dealer for details. To obtain local

dealer information, visit our website, wolfap-

pliance.com.

The control module can be positioned horizon-

tally or vertically and located anywhere within

3 m of the downdraft assembly and a

minimum of 76 mm from edge of cooktop cut-

out. Refer to page 11 for instructions to install

the control module.

IMPORTANT NOTE:

The downdraft must be

used with a Wolf-approved control module and

top cover.

COUNTERTOP CUT-OUT

Layout and cut the cooktop cut-out far

enough forward so the downdraft will fit

behind it.

Set the cooktop in place and slide it as far

forward as possible. Center and square the

cooktop with edges of countertop.

Place the plastic template included with the

downdraft against the back flange of the

cooktop and centered. Trace around the

template to mark the downdraft opening.

Remove the cooktop from countertop.

Cut the downdraft opening. Be careful not

to chip the edges of the countertop.

686 mm

FOR MODEL ICBDD30

838 mm

FOR MODEL ICBDD36

1067 mm

FOR MODEL ICBDD45

64 mm min

76 mm

min FOR

CONTROL

MODULE

COOKTOP CUT-OUT

WIDTH

638 mm min

FLAT

COUNTERTOP

SPACE

489 mm

70 mm

COUNTERTOP TOP VIEW

Countertop cut-out dimensions

WOLF DOWNDRAFT VENTILATION SYSTEMS

leveling bracket – flange facing in

leveling bracket –

flange facing out

mounting screws

Downdraft mounting brackets

CONTROL MODULE

The remote-mounted control module and top

cover are included with the downdraft. Also

included are mounting brackets, RJ45 connec-

tor and mounting hardware.

The control module can be located anywhere

within reach of the 3 m power cable and a

minimum of 76 mm from edge of cooktop

cut-out. The remote-mounted control module

is 60 mm x 168 mm and can be positioned

horizontally or vertically in the countertop.

IMPORTANT NOTE:

Do not place the module

where it will be in the way of cooking, where

hot pans may be placed or where hot liquids

could be spilled on the controls.

To reduce the risk of burns or ignition of

clothing by reaching across burners,

control module must be mounted at least

76 mm from edge of cooktop cut-out.

DOWNDRAFT INSTALLATION

Set the downdraft into the opening. Extend

the leveling brackets to the floor of the

cabinet so the downdraft sits straight.

NOTE: The leveling brackets can be

removed and reattached in other positions.

The flange of the leveling bracket may have

to face inward in tight cabinet installations.

Refer to the illustration below.

Secure the downdraft to the countertop by

holding the downdraft against the back of

the countertop cut-out and tightening the

two mounting screws (one on each end of

unit) on the underside of the countertop.

Screw the leveling brackets to the bottom

of the cabinet. Tighten the screws holding

the leveling brackets to unit on each side.

Autres manuels pour ICBDD30

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Wolf hotte de ventilation

Wolf

Wolf PW422718 Instructions d'utilisation

Wolf

Wolf PW362210 Instructions d'utilisation

Wolf

Wolf W302718 Manuel utilisateur

Wolf

Wolf W422418 Instructions d'utilisation

Wolf

Wolf W542718 Instructions d'utilisation

Wolf

Wolf PW662418 Instructions d'utilisation

Wolf

Wolf I363418 Manuel utilisateur

Wolf

Wolf Downdraft Ventilation Manuel utilisateur

Wolf

Wolf PW302718(R) Instructions d'utilisation

Wolf

Wolf W302418 Instructions d'utilisation

Wolf

Wolf CTWH30 Manuel utilisateur

Wolf

Wolf PI663418 Instructions d'utilisation

Wolf

Wolf Pro Wall Series Manuel utilisateur

Wolf

Wolf Drawer Microwave Oven Manuel utilisateur

Wolf

Wolf PL522212 Instructions d'utilisation

Wolf

Wolf CTWH30 Manuel utilisateur

Wolf

Wolf W482210 Instructions d'utilisation

Wolf

Wolf PW482210 Manuel utilisateur

Wolf

Wolf Pro Island Ventilation Hoods Manuel utilisateur

Wolf

Wolf W362418 Manuel utilisateur

Wolf

Wolf Pro Wall Manuel utilisateur

Wolf

Wolf PW302210 Manuel utilisateur

Wolf

Wolf PL342212 Manuel utilisateur

Wolf

Wolf PL462212 Instructions d'utilisation

Manuels hotte de ventilation populaires d'autres marques

emmeti

emmeti RECUPA MED A-140 Mode d’emploi

Nibe

Nibe F135 Manuel utilisateur

Kuppersberg

Kuppersberg INTRO 60 Instructions d'installation et d'entretien

Zephyr

Zephyr Spruce AK9834BS Guide d'installation

Hisense

Hisense MH6INBG Manuel utilisateur

Miele

Miele DA 1255 Manuel utilisateur

Broan

Broan 46000 Manuel utilisateur

GE Profile PV977 Instructions originales

FALMEC

FALMEC FFRIA24W5FS Manuel utilisateur

Whirlpool

Whirlpool RH2600XL-1 SERIES Manuel utilisateur

Küppersbusch

Küppersbusch DX ISLA Manuel utilisateur

ETNA

ETNA AV360RVS Manuel utilisateur

JUNO

JUNO JDF603E6 Manuel utilisateur

Miele

Miele DA 6708 D Manuel utilisateur

Tricity Bendix

Tricity Bendix LE 150 Manuel

AEG

AEG X68163BV1 Manuel utilisateur

AEG

AEG 125 D Manuel utilisateur

Smeg

Smeg KSEV97X Manuel utilisateur