Wiznet WizFi630 Instructions d'installation
Serial Command Guide
For
WizFi630 Users
(Version 1.0)
©2012 WIZnet Co., Ltd.All Rights Reserved.
☞For more information, visit our website at http://www.wiznet.co.kr
This document describes usages for WizFi630 WIFI AP Module. Descriptions scope and
boundary is limited as bellows
Testing environments
Networks operation mode
Serial operation Modem
Supplied software usages
Serial command definition
Table of contents
1. TEST ENVIRONMENT SETUP ......................................................................... 1
1.1 System Setup.................................................................................................................................................. 1
1.2 WizFi630’s default serial configuration. .................................................................................................. 1
1.3 PC #3 Setup.................................................................................................................................................... 1
1.4 PC #1 and PC#2 Serial Setup. .................................................................................................................... 1
2. SIMPLE SERIAL COMMAND AT SERIALTERMINAL PROGRAM ........... 2
3. WIZSMARTSCRIPT FOR WIZFI630 ................................................................ 3
3.1 Run Program .................................................................................................................................................. 3
3.2 Get Basic......................................................................................................................................................... 4
3.3 Functions ..................................................................................................................................................... 10
3.4 Set Operation Mode ................................................................................................................................... 14
3.5 Set Serial ...................................................................................................................................................... 18
4. SERIAL COMMAND DEFINITIONS ............................................................. 20
5. ACCESSING MODULE VIAWEB BROWSER ............................................. 26
6. MORE INFORMATION ................................................................................... 27
1
1. Test Environment Setup
1.1 System Setup
<WizFi630> 802.11 b/g/n WIFI AP Module
<PC#1> Serial Terminal Program running and connected to WizFi630’s Serial Port #1
<PC#2> Serial Terminal Program running and connected to WizFi630’s Serial Port #2
<PC#3> TCP Server application is running
1.2 WizFi630’s default serial configuration.
A. WizFi630 Serial Port #1 enabled
B. Serial configuration : 38400 / 8 data / No Parity / 1 Stopbits / No Flow control
C. TCP Client Mode / Connection Port 5000
D. Aux Connection Disabled
E. WizFi630 Serial Port #2 disabled
1.3 PC #3 Setup.
F. PC#3’s WIFI site survey and connect to ssid named “WLAN-AP”
G. Check IP address of PC#3
H. Chck IP address att “CMD window”, use ipconfig
1.4 PC #1 and PC#2 Serial Setup.
I. Supplied Serial cable is made with “RJ45 to DIP9”
J. Connect Serial cable to WizFi630’s Serial Port #2
K. Connect Serial cable to WizFi630’s Serial Port #2
2
2. Simple serial command at serial terminal program
①<RF>
This command gets module’s firmware version and normally used to check module is
working or not
②<ATDT>
This command changes module’s “serial working mode” as data mode
This is special command so do not type each character and <ATDT> copy and paste it at
terminal program.
③<+++>
This command changes module’s serial working mode as “command mode”.
In serial command, Incoming serial data is processed as serial command. In data mode,
Incoming serial data is processed as data and it is sent remote network hosts. This is special
command so do not type each character and <++++> copy and paste it at the terminal
program..
④<ATDT?>
This command responses module’s current serial working mode.
Response “1” : serial server is data mode
Response “0” : serial server is command mode
This is special command so do not type each character and <ATDT?> copy and paste it at
terminal program.
⑤<WP>
This command set network TCP/UDP port number.
As network server mode, it works as network incoming port number
As network client mode, it is remote host network port number to connect server
Ex) <WP5000> // Set port # as 5000
⑥<WX>
This command set remote host IP address.
When set, module connect remote host automatically. Ex) <WX192.168.16.11>
⑦<RQ>
This command responses serial sever’s network connection status.
0: Not Connect
1: Connect as client
2: Connected as server
3: Connected as Client/Server
⑧<WL>
This command saves configured data to flash.
When this command is processed, configed data is kept even if rebooting.
⑨<abc11>;
This is not command and it is one of sample user data for test
3
3. WIZSmartScript for WizFi630
3.1 Run Program
①If you run the WIZSmartScript program, you can see the KEY Confirm Dialog
as shown below.
②If you enter the received CODE and KEY, you can operate the program in
normal mode.
4
3.2 Get Basic
A. Get Module Information
①Input the COM port of PC and baud rate. (Default Baud Rate : 38400)
②Select “WizFi630” for Model, “A. Get Basic” for Group and “1. Get
Module Information” for Script.
③If you click “Start Script”, you can see the basic information of WizFi630 as
below.
5
B. Get Network Information
①Select “WizFi630” for Model, “A. Get Basic” for Group and “2. Get
Network” for Script.
②If you click “Start Script”, you can see the network information of
WizFi630 as below.
6
C. Get Wireless Information
①Select “WizFi630” for Model, “A. Get Basic” for Group and “3. Get
Wireless” for Script.
②If you click “Start Script”, you can see the wireless information of
WizFi630 as below.
7
D. Get Wireless(Client) Information
①Select “WizFi630” for Model, “A. Get Basic” for Group and “4. Get
Wireless (Client)” for Script.
②If you click “Start Script”, you can see the wireless(Client) information of
WizFi630 as below.
8
E. Get Wireless(AP-Client) Information
①Select “WizFi630” for Model, “A. Get Basic” for Group and “5. Get
Wireless (Client-AP)” for Script.
②If you click “Start Script”, you can see the wireless(AP-Client) information
of WizFi630 as below.
Autres manuels pour WizFi630
8
Table des matières
Autres manuels Wiznet Unité de contrôle
Wiznet
Wiznet WIZ200WEB Manuel utilisateur
Wiznet
Wiznet EG-SR-7100A Manuel utilisateur
Wiznet
Wiznet W7500S2E-R1 Manuel utilisateur
Wiznet
Wiznet WIZ107SR Manuel utilisateur
Wiznet
Wiznet W5500S2E Manuel utilisateur
Wiznet
Wiznet WIZ140SR Manuel utilisateur
Wiznet
Wiznet WIZ810Sio Manuel utilisateur
Wiznet
Wiznet WIZ120SR Manuel utilisateur
Wiznet
Wiznet W7100 Debugger Manuel utilisateur
Wiznet
Wiznet WIZ105SR Manuel utilisateur
Wiznet
Wiznet WIZ1000 Manuel utilisateur
Wiznet
Wiznet WIZ630wi Manuel utilisateur
Wiznet
Wiznet W5500S2E-S1 Manuel utilisateur
Wiznet
Wiznet W7500S2E Series Manuel utilisateur
Wiznet
Wiznet WIZ820io Manuel utilisateur
Wiznet
Wiznet IGM7100 Manuel utilisateur
Wiznet
Wiznet WIZ610wi Manuel utilisateur
Wiznet
Wiznet WIZ120SR Manuel utilisateur
Wiznet
Wiznet WIZ610io Manuel utilisateur
Wiznet
Wiznet WIZ6000 Manuel utilisateur
Manuels Unité de contrôle populaires d'autres marques
Festo
Festo Compact Performance CP-FB6-E Manuel de la liste des pièces
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur
JS Automation
JS Automation MPC3034A Manuel utilisateur
JAUDT
JAUDT SW GII 6406 Series Guide rapide
Spektrum
Spektrum Air Module System Manuel utilisateur
BOC Edwards
BOC Edwards Q Series Manuel utilisateur
