Wittkopp Primor 1600 Guide de l'utilisateur

Primor 1600

Installer manual

Installation and commissioning instructions

en_02 P1600-Part 2b-Installer manual V1.00

1 / 5

Note:

On the cover sheet you can find warning information, and an explanation of the symbols and

terms used, together with the exclusion of liability.

Contents

General................................................................................................................................. 2

Preparation for installation..................................................................................................... 3

Installation dimensions for lock 1600................................................................................. 3

Preparation of the boltwork / door...................................................................................... 3

Installation............................................................................................................................. 4

Wiring / installation................................................................................................................ 4

Function test.......................................................................................................................... 5

Input of the opening code.................................................................................................. 5

Keypad test ....................................................................................................................... 5

Mount the keypad before installing the electronic lock. All the keypads of the Primor series

can be used. For information on how to install the keypads, please refer to "Part 2a- Primor

keypad installer manual".

Primor 1600

Installer manual

Installation and commissioning instructions

en_02 P1600-Part 2b-Installer manual V1.00

2 / 5

General

P1600 series locks have standard

installation dimensions and can be installed

in all 4 installation positions (right, left, top,

bottom). They are designed for boltworks

with a one-sided locking edge, i.e. only for

force absorption by the straight boltwork

flank of the quarter-circle-shaped bolt.

They are intended to be installed in safes

made of metal.

The electronic lock requires no

maintenance in a normal residential or

office environment. We recommend a

security and function test of the electronic

lock after around 10,000 closings.

It is essential that the lock is protected

against attacks from outside. We

recommend that you protect against access

the security-relevant parts of the high-

security lock also when the door of the

container that holds the valuables is open.

It is not permissible to use two locks of the

same type in connection with analogue

keypads without any additional

components for locking state detection.

Do not apply any lubricants or other

substances to the lock.

Always use the following sequence for installation:

•Check the preconditions for installation

•Wiring / installation of the cables

•Set up the power supply

•Function test of the locking mechanism

•Perform all settings (user installation, delay time)

Ensure that the load limits are not exceeded at any time.

You can find the corresponding values in Annex C "Technical data".

Primor 1600

Installer manual

Installation and commissioning instructions

en_02 P1600-Part 2b-Installer manual V1.00

3 / 5

Preparation for installation

Installation dimensions for lock 1600

Preparation of the boltwork / door

To install the lock, there must be three

threaded holes for fastening on the

boltwork or inside the safe door. The

electronic lock must be fastened with the

supplied screws or M6 or 1/4” cylinder

screws (min. strength class 8.8). The screw

length should be measured so that a

minimum screw-in depth of 6 mm is

possible.

Drilling pattern:

The electronic lock can be installed in the area of openings with a maximum diameter of 11.5

mm around the axis centre shown above.

This hole is not required on Primor 1000 / 1600 / 2000.

Primor 100 / 2000: Centre of electronic lock drive is flush with centre of

input unit (Primor RO)/centre of keypad lever (Primor RE)

Primor 1600

Installer manual

Installation and commissioning instructions

en_02 P1600-Part 2b-Installer manual V1.00

4 / 5

Installation

The retaining screws must be tightened in

such a way that a permanent and firm hold

is ensured.

Tighten the fastening screws with a

maximum torque of 6 Nm. To prevent the

screws from becoming loose, the screws

must be secured using safety washers or

using screw locking agents.

There must be no tension or pressure on

the lock bolt after installation.

Make sure there is sufficient clearance to

the locking point.

Wiring / installation

Cut off the power supply / battery, before starting any work or making any changes to the

wiring between the lock and keypad.

Lock cable entry

Plug

Connecting cable

Primor 1600

Installer manual

Installation and commissioning instructions

en_02 P1600-Part 2b-Installer manual V1.00

5 / 5

Function test

Carry out a function test after completing all

the mounting and installation work.With the

door open, you should open and close the

lock several times using the master code

that had been set at the factory.

The relationship between easy opening and

reliable closing can be set via the operating

lever of the boltwork.

The locking check can be done via the

operating lever of the boltwork and should

be performed after each closing and

locking.

Input of the opening code

e.g. master factory code





=✓

→



The opening code can be input

directly as described above, without

selection. The bolt is released for

approx. 3 seconds after a valid

code has been entered. Open the

container with the valuables within

this time after inputting the code.

=



Keypad test

We recommend a final keypad test using function menu 5 to ensure that all the numeric keys

function properly.



☼Checking the menu system

Press the keys in the

sequence

…



=✓

Press each numeric key once. A

functional key is indicated by a

double signal tone.

A key that is not recognised is

indicated by a long signal tone and

the function test is terminated. The

system must be checked.

Table des matières

Autres manuels Wittkopp Verrouillage

Wittkopp

Wittkopp Primor 1000 Manuel utilisateur

Wittkopp

Wittkopp SmartCam Manuel utilisateur

Wittkopp

Wittkopp ANCHOR Manuel utilisateur

Wittkopp

Wittkopp ElCom 7205 Manuel utilisateur

Wittkopp

Wittkopp Primor Level 5 Manuel utilisateur

Wittkopp

Wittkopp Primor 100 Manuel utilisateur

Wittkopp

Wittkopp GATOR F Manuel utilisateur

Wittkopp

Wittkopp Primor Series Manuel utilisateur

Wittkopp

Wittkopp Anchor 4000 Series Manuel utilisateur

Wittkopp

Wittkopp Anchor 7000 Mode d’emploi

Wittkopp

Wittkopp FinKey Manuel utilisateur

Wittkopp

Wittkopp Primor Level 25 Manuel utilisateur

Wittkopp

Wittkopp Primor 2600 Guide de l'utilisateur

Wittkopp

Wittkopp Primor 3000 Manuel utilisateur

Wittkopp

Wittkopp Anchor 4000 Series Guide de l'utilisateur

Wittkopp

Wittkopp Primor 1000 Guide de l'utilisateur

Wittkopp

Wittkopp 1619 Manuel utilisateur

Wittkopp

Wittkopp 7800 Manuel utilisateur

Wittkopp

Wittkopp Primor Series Manuel utilisateur

Wittkopp

Wittkopp Primor 2000 / Level 5 Manuel utilisateur

Wittkopp

Wittkopp OPTIMA 2648 Manuel utilisateur

Wittkopp

Wittkopp Insys 7202 Manuel utilisateur

Wittkopp

Wittkopp TwinLock 7220 Manuel utilisateur

Wittkopp

Wittkopp Anchor 2600 Guide de l'utilisateur

Manuels Verrouillage populaires d'autres marques

Magic

Magic 105 Manuel utilisateur

Gantner

Gantner GAT NET.Lock 7020 System Guide rapide

Dorma

Dorma Studio Classic Manuel utilisateur

Securam

Securam ECSL-601 Manuel utilisateur

Sudhaus

Sudhaus 3003 Manuel utilisateur

Safety 1st

Safety 1st 48517 Manuel utilisateur

Pado

Pado FDS-10 Manuel utilisateur

Esco

Esco systeQ Series Manuel utilisateur

COMPX

COMPX National D8951 Manuel utilisateur

secureo

secureo Key Box Manuel utilisateur

Stock Loks

Stock Loks C8713 Manuel utilisateur

COMPX

COMPX 1T-058 Manuel du propriétaire

Auslock

Auslock T11 Manuel utilisateur

ELCOM

ELCOM 7205 Manuel utilisateur

Stealth SAFES

Stealth SAFES ShadowVault Manuel utilisateur

Knox

Knox KeySecure 5 Manuel utilisateur

Kwikset

Kwikset 48334/01 Manuel utilisateur

Metra Electronics

Metra Electronics Door Access Terminal Combo Manuel utilisateur