Wittkopp Primor 100 Manuel utilisateur

Installation instructions no 9999-139-0

Installation instructions Primor 100

Content

1 General instructions _____________________________________________________________ 2

2 Installation input unit Primor RO ___________________________________________________ 2

3 Installation input unit Primor RE____________________________________________________ 4

4 Installation lock Primor 100_______________________________________________________ 6

5 Connection input unit/lock________________________________________________________ 9

6 Functional test __________________________________________________________________ 9

Installation instructions Primor 100

Rel. 1.1

1 General instructions

• Please read the installation instructions carefully, before activating the lock.

1.1 Liability notes

• The mounting of the electronic lock and the input unit has to be carried out according to the installation instruction.

• We point out that this installation instruction is part of the VdS-certiﬁcation and non-compliance leads to the loss of this

certiﬁcation.

• By opening the lock cover warranty of the manufacturer will be void.

• Take care that the input unit or the lock and the cables should not be damaged.

2 Installation input unit Primor RO

2.1 Input unit Primor RO 2.1.1 Dimensions Primor RO

2.2 Installation overview

2.2.1 Input unit Primor RO

Fixing ring for input unit

4 Cylinder screws M4 x 10

Connection axis for

turnable input unit

Input unit

Connection cable

Installation instructions Primor 100

Rel. 1.1

2.3 Axis length calculation input unit Primor RO

2.3.1 In connection with Primor 100 2.3.2 Door drilling for connection axis

Connection axis:

Debur the ends

L = A + 43mm (Toleranz - 4mm)

Türlochbohrung

mind. ø9 - max. ø10,6

mind . ø10,6 - max. ø11,4

min. Ø 10,6 mm/max. Ø 11,4 mm

L = A + 28 mm (tolerance -4 mm)

2.4 Mounting

2.4.1 Drill pattern fixing Primor RO

4 x Fixing position for M4

Hole center congruent with middle

axis of nut of the electronic lock.

Opening for cable

• From the front 4 threaded holes M4 with sufﬁcient depth thread and 1 through-hole (opening for cable/connection axis)

have to be drilled into the safe door.

• From the front the ﬁxing ring has to be ﬁxed with the enclosed cylinder screws M4 x 10.

2.4.2 Mounting input unit Primor RO

Position 1

20°

Position 2

• Position 1: Mount the input unit with an angle of approx. 20° to the ﬁxing ring.

• Position 2: Turn the input unit to the right into position. The turning has to happen easily.

Installation instructions Primor 100

Rel. 1.1

2.4.3 Cable guidance Primor RO 2.4.4 Plug position Primor RO

Connection axis

Plug position

• Lead connection cable through the input unit.

• Insert the connection axis into the input unit from behind.

• Lead connection cable through the input unit and connect the plug.

3 Installation input unit Primor RE

3.1 Input unit Primor RE 3.1.1 Dimensions Primor RE

205

3.2 Installation overview

3.2.1 Input unit Primor RE

Lever

axe proﬁle

black covering cap

red covering cap

Cylinder screws

M5 x 14

Cylinder screws

M5 x 18

O-Ring

Installation instructions Primor 100

Rel. 1.1

3.3 Axis length calculation input unit Primor RE

3.3.1 In connection with Primor 100 3.3.2 Door drilling for connection axis

Connection axis:

Debur the ends

L = A + 43mm (Toleranz - 4mm)

Türlochbohrung

mind. ø9 - max. ø10,6

mind . ø10,6 - max. ø11,4

min. Ø 10,6 mm/max. Ø 11,4 mm

L = A + 35 mm (tolerance -2 mm)

3.4 Mounting

3.4.1 Drill pattern Primor RE (lock is closing towards the right) - (closing towards the left inversely)

Ø 11,4

60 145

130

100

Opening for cable

2 x Fixing position for

screws M5 x 14

2 x Fixing position

for screws M5 x 18

• From the front 4 threaded holes M5 with sufﬁcient depth thread and 1 through-hole (opening for cable/connection axis)

have to be drilled into the safe door.

3.4.2 Cable guidance Primor RE 3.4.3 Plug position Primor RE

Connection axis retaining washer

O-Ring

• Lead the connection cable through the connection axis.

• Plug the connection axis into the lever.

• Push the cable and the O-ring in the direction of the arrow until the inset.

• Connect the plug of the cable with the plug on the circuit board.

• Attention: Don’t put the connection cable under tensile stress.

• Fix the input unit from the front with the enclosed cylinder screws M5.

Installation instructions Primor 100

Rel. 1.1

4 Installation lock Primor 100

Before mounting the lock the input unit RO or RE has to be installed (see up to page 2).

• The lock can be installed in all conventional safes.

• The maximal bolt load against ist closing direction may not excel 5N.

• Depending on the model there can be optional used more locking elements (e.g. angle with bolts) additional to the existing

holes of the bolt. Please make sure that the lock and the connections operate properly.

• Mind sufﬁcient slackness of the locking point.

• The electronic lock has got standard installation dimensions and can be mounted in all installation directions (right-hand,

left-hand, upwards, downwards).

• The electronic lock has to be protected against external attacks.

• Do not insert any lubricants or other substances into the electronic lock.

• The electronic lock is maintenance free in normal domestic and ofﬁce surroundings. After approx. 10,000 closures it is re-

commended to carry out a security and functional test of the electronic lock.

4.1 Dimensions

4.1.1 Dimensions lock Primor 100

Middle-axis of the nut has to be

congruent with the middle-axis of the

input unit

Hub/Stroke 12

14 +12mm

Ø4,5

25,4

60,7

9,1 66,5

Platzbedarf/Required space

4.1.2 Option extension latch 4.1.3 Option lock cover - screwed

66,5

Ø6,5

110

112,5

142

66,5

Ø6,5

110

112,5

142

Installation instructions Primor 100

Rel. 1.1

4.1.4 Option lock cover - welded

(without anti-drilling plate)

4.1.5 Option lock cover - welded

(with anti-drilling plate)

66,5

Ø6,5

110

112,5

142

66,5

Ø6,5

110

112,5

142

If the lock is mounted without ist lock case further installation guidelines have to be considered. Non-observance leads to

loss of VdS certiﬁcation. A separate installation instruction can be found on www.carl-wittkopp.com.

4.2 Mounting lock Primor 100 - lock cover screwed

4.2.1 Dimensions lock Primor 100 - lock cover srewed

Hub/Stroke 12

9,1

66,5

102

142

25,4

Ø4,5

Ø6,5

60,7

110

115

Platzbedarf für Riegelhub /

Required space for bolt throw

2,5

• For ﬁxing the electronic lock 4 threaded holes M6 with depth min. 6 mm (or a comparable inch thread) have to be drilled

into the safe door.

• Optional: Insert extension latches into the guiding pins at the back of the lock in the right direction and pull up the extensi

on latch that closes to the top.

• The lock case is put on top of the electronic lock.

• Lead the connection cable of the input unit through the square nut of the lock.

Attention: Don’t put the connection cable under tensile stress.

•Fixing the lock with screws M6 or a comparable inch thread. Length and material application of the screw has to be selected

such as a secure long-term stability is guaranteed.

• Independent loosening of the screws has to be avoided. Recommendation: put lock washers underneath the screw’s head

• Turn the screws with a maximum turning force of 3.5 – 5 Nm.

• Mind sufﬁcient slackness of the locking point.

Installation instructions Primor 100

Rel. 1.1

4.3 Mounting lock Primor 100 - lock cover welded

4.3.1 Dimensions lock 100 - lock cover welded

(without anti-drilling plate)

4.3.2 Dimensions lock Primor 100 - lock cover welded

(with anti-drilling plate)

Hub/Stroke 12

142

25,4

Ø4,5

102,1

97027

110

115

60,7

Platzbedarf für Riegelhub /

Required space for bolt throw

2,5

Hub/Stroke

142

25,4

Ø4,5

112,5

115

102

Platzbedarf für Riegelhub /

Required space for bolt thro

2,5

• Before welding the lock cover, the lock case has to be removed.

• When positioning keep the middle of the connection axis congruent with the input unit RO/RE.

• Weld the lock case (if so with hardened manganese steel plate) with 4 welding seams, length 15-20 mm (position of the

welding seams on the corners oft he lock case) to the inside of the safe door.

• Welding distortion must be avoided.

• Lead the connection cable of the input unit through the square nut of the lock.

Attention: Don’t put the connection cable under tensile stress.

• The lock then has to be plugged onto the connection axis of the input unit, which is already in the safe door.

•Optional: Insert extension latches into the guiding pins at the back of the lock in the right direction and pull up the extension

latch that closes to the top.

• The electronic lock has to be ﬁxed with the 4 enclosed ﬂat-headed screws M6 x 12 with the designated drillings of the lock

case in order that permanent foothold is guaranteed.

• Turn the screws with a maximum turning force of 3.5 – 5 Nm.

• After the installation the bolt/extension latches may not be under pressure or strain.

Installation instructions Primor 100

Rel. 1.1

5 Connection input unit/lock

5.1 Primor 100

Plug position

• Connect the plug of the input unit with the lock in its designated position.

• Connect the battery with its clip.

• Only use 9v block batteries.

• Keep the cables away from sharp edges and movable components and ﬁx permanently.

6 Functional test (when the door is open)

Carry out a functional test after installing the lock and input unit.

• Enter the factory code 1 – 2 – 3 – 4 – 5 – 6.

• Within 3 seconds turn the input unit into the opening position. The lock bolt moves in (has to happen easily). The lock is

opened.

• Turn the input unit into the locking position. The lock bolt moves out and locks. The lock is closed.

• Keep enough clearance to the locking point..

Table des matières

Autres manuels Wittkopp Verrouillage

Wittkopp

Wittkopp Primor 3000 Manuel utilisateur

Wittkopp

Wittkopp Primor Series Manuel utilisateur

Wittkopp

Wittkopp Anchor 7000 Mode d’emploi

Wittkopp

Wittkopp TwinLock 7220 Manuel utilisateur

Wittkopp

Wittkopp Primor Level 5 Manuel utilisateur

Wittkopp

Wittkopp GATOR F Manuel utilisateur

Wittkopp

Wittkopp Primor 1000 Guide de l'utilisateur

Wittkopp

Wittkopp Anchor 7000 Manuel utilisateur

Wittkopp

Wittkopp Primor P30 Series Manuel utilisateur

Wittkopp

Wittkopp Anchor 4000 Series Manuel utilisateur

Wittkopp

Wittkopp Anchor 2600 Guide de l'utilisateur

Wittkopp

Wittkopp FinKey Manuel utilisateur

Wittkopp

Wittkopp Primor 1000 Manuel utilisateur

Wittkopp

Wittkopp Primor 1600 Guide de l'utilisateur

Wittkopp

Wittkopp Anchor 4000 Series Guide de l'utilisateur

Wittkopp

Wittkopp 7800 Manuel utilisateur

Wittkopp

Wittkopp ANCHOR Manuel utilisateur

Wittkopp

Wittkopp Primor 2000 / Level 5 Manuel utilisateur

Wittkopp

Wittkopp Insys 7202 Manuel utilisateur

Wittkopp

Wittkopp Primor Level 25 Manuel utilisateur

Wittkopp

Wittkopp Primor Series Manuel utilisateur

Wittkopp

Wittkopp BlueCam greendot Manuel utilisateur

Wittkopp

Wittkopp 1619 Manuel utilisateur

Wittkopp

Wittkopp ElCom 7205 Manuel utilisateur

Manuels Verrouillage populaires d'autres marques

Magic

Magic 105 Manuel utilisateur

Gantner

Gantner GAT NET.Lock 7020 System Guide rapide

Dorma

Dorma Studio Classic Manuel utilisateur

Securam

Securam ECSL-601 Manuel utilisateur

Sudhaus

Sudhaus 3003 Manuel utilisateur

Safety 1st

Safety 1st 48517 Manuel utilisateur

Pado

Pado FDS-10 Manuel utilisateur

Esco

Esco systeQ Series Manuel utilisateur

COMPX

COMPX National D8951 Manuel utilisateur

secureo

secureo Key Box Manuel utilisateur

Stock Loks

Stock Loks C8713 Manuel utilisateur

COMPX

COMPX 1T-058 Manuel du propriétaire

Auslock

Auslock T11 Manuel utilisateur

ELCOM

ELCOM 7205 Manuel utilisateur

Stealth SAFES

Stealth SAFES ShadowVault Manuel utilisateur

Knox

Knox KeySecure 5 Manuel utilisateur

Kwikset

Kwikset 48334/01 Manuel utilisateur

Metra Electronics

Metra Electronics Door Access Terminal Combo Manuel utilisateur