Wittkopp Anchor 2600 Guide de l'utilisateur

Anchor 2600

Installer manual

Installation and commissioning instructions

02 en_A2600-Teil 2b-Errichterhandbuch V2.03.docx

1 / 7

Note:

On the cover sheet you can find warning information, and an explanation of the symbols and

terms used, together with the exclusion of liability.

Contents

General................................................................................................................................. 2

Preparation for installation..................................................................................................... 3

Installation dimensions A2600........................................................................................... 3

Preparation of the boltwork / door...................................................................................... 3

Installation............................................................................................................................. 4

Wiring / installation................................................................................................................ 4

Connection of an analog keypad ....................................................................................... 5

Connection P- signal plus / UART ..................................................................................... 5

Function test.......................................................................................................................... 6

Input of the opening code.................................................................................................. 6

Keypad test ....................................................................................................................... 6

System setup ........................................................................................................................ 7

Mount the keypad before installing the electronic lock. All the keypads of the Primor series

with direct drive can be used (RO, RE). The function is generally given with all input units

of the Primor series, an additional handle for the drive of the bolt is needed, depending on

which keyboard was chosen. Details on installing the keypads are given in the installation

instructions (see sections “en_02 en_APxxx-Teil 2a-Errichterhandbuch Tastatur V2.05”).

Anchor 2600

Installer manual

Installation and commissioning instructions

02 en_A2600-Teil 2b-Errichterhandbuch V2.03.docx

2 / 7

General

Locks of the Anchor 4000 series have

standard installation dimensions and can

be mounted in all 4 installation positions

(right, left, top, bottom). They have been

designed for a boltwork with two blocking

edges, i.e. for the force to be applied only

on only the flank of the bolt.

They are intended to be installed in safes

made of metal.

Depending on the design, additional

blocking elements (e.g. bolt rails) can

optionally be attached to the lock bolt

using existing holes. A perfect function of

the lock and its connection must be

ensured.

The electronic lock requires no

maintenance in a normal residential or

office environment. We recommend a

security and function test of the electronic

lock after around 10,000 closings.

The breakthrough for the axis must not

exceed 11.4mm.

The lock must be protected against

attacks from outside. It is recommended to

protect the security-relevant parts of the

high-security lock against access even

when the door of the safe is open.

Do not apply any lubricants or other

substances to the lock.

Always use the following sequence for installation:

•Check the preconditions for installation

•Wiring / installation of the cables

•Set up the power supply

•Function test of the locking mechanism

•Make all the settings (user system, Dualcode, inputs and outputs, delay time)

Ensure that the load limits are not exceeded at any time.

You can find the corresponding values in Annex C "Technical data".

Anchor 2600

Installer manual

Installation and commissioning instructions

02 en_A2600-Teil 2b-Errichterhandbuch V2.03.docx

3 / 7

Preparation for installation

Installation dimensions A2600

Preparation of the boltwork / door

For mounting the lock there must be three

threaded holes for attachment to the

boltwork or within the safe door. The

electronic lock is to be attached with the

supplied M6 or 1/4" screws or cylinder

screws (minimum strength class 8.8).

The length of the screws must be 25 mm or

more so that a minimum screw-in depth of

5 mm is attained.

Anchor 2600

Installer manual

Installation and commissioning instructions

02 en_A2600-Teil 2b-Errichterhandbuch V2.03.docx

4 / 7

Installation

The fastening screws must be tightened so

that a permanent and firm hold is

guaranteed.

Tighten up the fastening screws to a

maximum torque of 3,5 –5 Nm. We

recommend the use of a bolt locking agent

(adhesive) to prevent the screws from

coming undone by themselves.

The bolt of the lock may not be under

tension or pressure after installation.

Pay attention to enough free space to the

blocking point.

Wiring / installation

If the lock is operated outside the area of

validity of the VdS, then signal boxes,

external power supplies, etc. can be used

with the Anchor in addition to all the analog

keypads that are compatible with the

Primor series.

The VdS approval is restricted to operation

with input units of the Primor FS, FL, RO,

RE and Anchor LC series.

If the wiring is not guided by the drive axis,

the required hole / way of wiring must be

selected in such a way that this gives no

access to the lock body through tools,

probes or similar.

Drilling for the wiring must be at least 8mm,

a maximum of 11.4mm.

For all work / changes to the wiring between the lock, keypad or signal boxes, the power

supply including the battery must be disconnected!

Anchor 2600

Installer manual

Installation and commissioning instructions

02 en_A2600-Teil 2b-Errichterhandbuch V2.03.docx

5 / 7

Connection of an analog keypad

As supplied, onlythe interface for an analog

keypad from the Primor series is active. If

the lock is to communicate with a digital

input unit, i.e., an "intelligent" one, then

additional settings are required in the setup

menu [6] in addition to the selection of the

corresponding interface or socket.

You can find the corresponding commands

in the user manual.

You can find information on inserting the

battery in the operating manual of the

corresponding Primor keypad.

Connection P- signal plus / UART

Connection via the second port (see above)

is always done if

•the lock system has an external

power supply,

•a "silent alarm" contact for

evaluation by an alarm system has

been made available,

•a system block by an external

signal (dry contact) is to be used.

Additional hardware is required to do this.

The lock is compatible with all the available

components of the Primor series.

You can find informationon the wiring in the

instructions for the signal box. The VdS

approval is no longer valid when used in

conjunction with a signal box or if the serial

interface (UART) is not used correctly.

analog keypad

e.g. Primor RO

serial interface [UART] or

[IO] for Alarmbox

If a signal block with "active release" (switching logic) has been set up this ensures that the

blocking is not switched off if the control cable iscut through. At the same, a cable breakage

within the safe always thus entails the risk of a blockade.

Anchor 2600

Installer manual

Installation and commissioning instructions

02 en_A2600-Teil 2b-Errichterhandbuch V2.03.docx

6 / 7

Function test

Carry out a function test after completing all

the mounting and installation work.With the

door open, you should open and close the

lock several times using the master code

that had been set at the factory.

The opening takes place after the release

by turning the keyboard (RO) or the

operating lever (RE):

Using the handle for the boltwork the safe

should be openedeasilyand reliablyclosed

again.

The locking check can be done via the

operating lever of the boltwork and should

be performed after each closing and

locking.

Input of the opening code

e.g. factory code Master





=✓

→



The opening code can be input

directly as described above, without

selection. After a valid code is input

the lock releases the bolt

movement for around 3 seconds.

Open the container with the

valuables within this time after

inputting the code.

=



Keypad test

We recommend a final keypad test using function menu 5 to ensure that all the numeric keys

function properly.



☼Checking the menu system

Press the keys in the

sequence

…



=✓

Press each numeric key once.

A functional key is indicated by a

double signal tone.

A key that is not recognised is

indicated by a long signal tone and

the function test is terminated. The

system must be checked.

Anchor 2600

Installer manual

Installation and commissioning instructions

02 en_A2600-Teil 2b-Errichterhandbuch V2.03.docx

7 / 7

System setup

The setting options and the control sequences that are required are described in the user

manual.

We therefore recommend the following procedure:

•Setup of the users [menu 1]

•if applicable, parameterisation of the inputs and outputs [menu 6]

•if applicable, setting up the Dualcode condition [menu 6]

•if applicable, setting up the delay time [menu 9]

In particular, the user system can be made markedly faster by using setup mode [menu 8].

The repetitive input of the master code is then restricted to selecting setup mode.

Table des matières

Autres manuels Wittkopp Verrouillage

Wittkopp

Wittkopp Anchor 4000 Series Manuel utilisateur

Wittkopp

Wittkopp Anchor 7000 Mode d’emploi

Wittkopp

Wittkopp Anchor 4000 Series Guide de l'utilisateur

Wittkopp

Wittkopp Primor P30 Series Manuel utilisateur

Wittkopp

Wittkopp Primor 1000 Manuel utilisateur

Wittkopp

Wittkopp Primor 1000 Guide de l'utilisateur

Wittkopp

Wittkopp SmartCam Manuel utilisateur

Wittkopp

Wittkopp Primor Level 5 Manuel utilisateur

Wittkopp

Wittkopp TwinLock 7220 Manuel utilisateur

Wittkopp

Wittkopp Primor Series Manuel utilisateur

Wittkopp

Wittkopp Primor 2000 / Level 5 Manuel utilisateur

Wittkopp

Wittkopp Insys 7202 Manuel utilisateur

Wittkopp

Wittkopp Primor Series Manuel utilisateur

Wittkopp

Wittkopp Primor Level 25 Manuel utilisateur

Wittkopp

Wittkopp ElCom 7205 Manuel utilisateur

Wittkopp

Wittkopp Primor 100 Manuel utilisateur

Wittkopp

Wittkopp Primor 2600 Guide de l'utilisateur

Wittkopp

Wittkopp OPTIMA 2648 Manuel utilisateur

Wittkopp

Wittkopp BlueCam greendot Manuel utilisateur

Wittkopp

Wittkopp 7800 Manuel utilisateur

Wittkopp

Wittkopp GATOR F Manuel utilisateur

Wittkopp

Wittkopp FinKey Manuel utilisateur

Wittkopp

Wittkopp Primor 3000 Manuel utilisateur

Wittkopp

Wittkopp ANCHOR Manuel utilisateur

Manuels Verrouillage populaires d'autres marques

Magic

Magic 105 Manuel utilisateur

Gantner

Gantner GAT NET.Lock 7020 System Guide rapide

Dorma

Dorma Studio Classic Manuel utilisateur

Securam

Securam ECSL-601 Manuel utilisateur

Sudhaus

Sudhaus 3003 Manuel utilisateur

Safety 1st

Safety 1st 48517 Manuel utilisateur

Pado

Pado FDS-10 Manuel utilisateur

Esco

Esco systeQ Series Manuel utilisateur

COMPX

COMPX National D8951 Manuel utilisateur

secureo

secureo Key Box Manuel utilisateur

Stock Loks

Stock Loks C8713 Manuel utilisateur

COMPX

COMPX 1T-058 Manuel du propriétaire

Auslock

Auslock T11 Manuel utilisateur

ELCOM

ELCOM 7205 Manuel utilisateur

Stealth SAFES

Stealth SAFES ShadowVault Manuel utilisateur

Knox

Knox KeySecure 5 Manuel utilisateur

Kwikset

Kwikset 48334/01 Manuel utilisateur

Metra Electronics

Metra Electronics Door Access Terminal Combo Manuel utilisateur