Winegard TR-6100 Manuel utilisateur

This should clear

out any previously

installed devices.

Then, select Done.

Re-connect the

coaxial cable to

the “Satellite In”

port on the back

of the receiver.

DISH®Receiver Setup for TR-6100

DISH receivers will often not show when they are on signal if they have incorrect “Check Switch”

information. For this reason, DISH users must clear current settings before pointing. To do this for most

DISH receivers, follow these steps. The following instructions are based on a ViP®211 receiver.

If your receiver differs from the options shown, you may need to consult your receiver manual. The

wording and display used in your receiver may differ slightly.

Select option 1,

Point Dish.

Before starting,

disconnect coax

from “Sat in” on

back of receiver.

Press Menu on

your remote.

Select option 6,

System Setup.

Select option 1,

Installation.

Select

Check Switch.

For Help, Call 1-800-788-4417

Check that there

are no checkmarks

by SuperDISH or

Alternate. Select

Test.

The receiver will

go through a

number of steps

and then may

warn that fewer

satellites were

detected.

If so, select Save.

It may ask you to

confirm. If so,

select Save again.

Press Cancel

four times to

exit the receiver

menu.

The receiver

set-up is now

complete.

Now return to

steps 4 and 5

to run another

Check Switch

test. The result

should be what is

shown here.

If you are missing

any satellites or

have low signal

on a satellite, the dish will need to be adjusted.

Once accurately

pointed, the

signal meter will

turn green.

Make small

adjustments to

get the signal

as high as

possible. Check

that the bar at

the bottom of

the screen is green and that the satellite displayed is the

desired satellite.

1) In the first column, input zip code of current location. Note that whenever

you move the satellite antenna to a new location, you must enter the zip

code of your new current location.

2) In the second column, choose Dish 500. With this option selected, use the

angles on the screen as a starting point for pointing your satellite dish. The

actual angles for pointing your dish will be slightly different than those shown

on screen; make small adjustments until getting the signal as high as possible.

3) In the third column, use Transponder 11 for Satellite 119.

4) In the fourth column, the satellite should be whatever satellite you want to

point at. Satellite 119 is the primary satellite, and the majority of

programming is located here. Satellite 119 should be used for initial aiming.

Note: If using a 311 or previous model receiver, select Peak Angles to enter your satellite and zip code.

With all information entered, an azimuth, elevation, and skew angle will be displayed under the four columns. Record

these angles. Now, follow the instructions in the TR-6100 manual to point the dish using the azimuth, elevation, and

skew angles. Continue with step 9 of receiver setup after successfully pointing the dish.

Winegard is a registered trademark of Winegard Company.

DISH and ViP are registered trademarks of DISH Network L.L.C.

Autres manuels Winegard Antenne

Winegard

Winegard HD-9095P Manuel utilisateur

Winegard

Winegard RZ-6035 Manuel utilisateur

Winegard

Winegard DuraSAT D4 CM2000T Manuel utilisateur

Winegard

Winegard Movin' View MV-4005 Manuel utilisateur

Winegard

Winegard FlatWave Micro Manuel utilisateur

Winegard

Winegard Movin' View MV-0099 Manuel utilisateur

Winegard

Winegard YA-7000 Manuel utilisateur

Winegard

Winegard AIR 360+ Manuel utilisateur

Winegard

Winegard HD7000R Manuel utilisateur

Winegard

Winegard HD-8800 Manuel utilisateur

Winegard

Winegard Prostar 1000 PR-7010 Manuel utilisateur

Winegard

Winegard WX980 Manuel utilisateur

Winegard

Winegard YA7000C Manuel utilisateur

Winegard

Winegard PR-8800 Manuel utilisateur

Winegard

Winegard WV750 Manuel utilisateur

Winegard

Winegard WAVU W1 Manuel utilisateur

Winegard

Winegard roadtrip T4 RT2000T Manuel utilisateur

Winegard

Winegard SENSAR III Manuel utilisateur

Winegard

Winegard Rayzar Manuel utilisateur

Winegard

Winegard Movin' View MV3500T Manuel utilisateur

Winegard

Winegard MA1000W Manuel utilisateur

Winegard

Winegard HD7080P Manuel utilisateur

Winegard

Winegard Pathway X1 Manuel utilisateur

Winegard

Winegard Sensar HV CC-25HV Manuel utilisateur

Manuels Antenne populaires d'autres marques

Alfa Network

Alfa Network APA-L01 Manuel utilisateur

Naval

Naval PR-422CA Manuel utilisateur

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Manuel utilisateur

TERK Technologies

TERK Technologies TV44 Manuel utilisateur

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Manuel utilisateur

HP J8999A Manuel utilisateur

MobilSat

MobilSat MSP-S Manuel utilisateur

Steren

Steren ANT-UHF 13 Manuel utilisateur

Novatel

Novatel 600-G Manuel d'utilisation

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Manuel utilisateur

TRENDnet

TRENDnet TEW-AO12O Manuel utilisateur

Radio Shack

Radio Shack 15-1837 Manuel utilisateur

CommScope

CommScope CMAX-OMFX-43M-I53 Manuel utilisateur

Ramsey Electronics

Ramsey Electronics DAP25 Manuel utilisateur

COBHAM

COBHAM SAILOR 800 VSAT Manuel d'utilisation et d'entretien

Trango Systems

Trango Systems AD900-9 Manuel utilisateur

Steren

Steren ANT-100 Manuel utilisateur

Proxim

Proxim 5054-PA-23 Manuel utilisateur