Wilson Electronics DB Pro 271265 Manuel utilisateur

Wilson

Electronics, Inc.

Contents:

How it Works ......................................1

Quick Install Overview...............................2

Installation Diagram.................................3

Installing the Outside Antenna.........................5

Finding the Strongest Signal ..........................7

Installing the Inside Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Installing a Wilson Electronics Signal Booster. . . . . . . . . . . . . 9

Powering up a Wilson Electronics Signal Booster..........9

Understanding the Signal Booster Lights . . . . . . . . . . . . . . . 10

Warnings & Recommendations .......................12

Signal Booster Specifications . . . . . . . . . . . . . . . . . Back Cover

Note: This manual contains important safety and operating information. Please read and

follow the instructions in this manual. Failure to do so could be hazardous and result in

damage to your Signal Booster.

In-Building Wireless

800/1900 MHz

Smart Technology ™

Signal Booster

DB Pro

™

Adjustable Gain

Appearance of device and accessories may vary.

1Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660

or email: [email protected]. Hours: 7 am to 6 pm MST.

Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660

or email: [email protected]. Hours: 7 am to 6 pm MST.

Installation Instructions for the Following Wilson

Electronics Signal Booster:

DB Pro™ Adjustable Gain In-Building Wireless

800/1900 MHz Smart Technology ™ Signal Booster

Model # 271265

FCC ID: PWO271265 IC: 4726A-271265

The term “IC” before the radio certification number only signifies that Industry Canada

technical specifications were met.

How it Works

Wilson Electronics Signal Boosters are bi-directional devices that deliver

service levels consistent with what would be expected in areas of high cell

network coverage. The Outside Antenna will collect the cell tower signal

and send it through the cable to the Signal Booster. The signal is then

boosted and sent to the Inside Antenna. Your cell phone or data card then

communicates with the improved signal. When the cellular device transmits,

the signal goes through the Inside Antenna, is boosted by the Signal Booster

and transmitted to the cell tower through the Outside Antenna.

Inside this Package

DB Pro™

Signal Booster

AC/DC Power Supply

Accessories & Antenna Options (may be included in some kits)

To purchase call Wilson Electronics Sales Department at: 800-204-4104

1. 1900 MHz Yagi PCS Antenna (301124)*

2. 800 MHz Yagi Cellular Antenna (301129)*

3. 800/1900 MHz Omni-Directional Antenna

75 Ohm (301201)

4. 700-2700 MHz Wide Band Directional Antenna (304475)

5. 700-2700 MHz Wide Band Panel Antenna (301155)

6. Lightning Surge Protector 75 Ohm (859988)

Splitters options on page 8

Select a location to install the Signal Booster that is away from1.

excessive heat, direct sunlight, moisture and has proper ventilation.

Do not place the Signal Booster in an air-tight enclosure.

Select a location on the roof of the building to install the Outside2.

Antenna. Use a cell phone in test mode to find the strongest signal from

the cell tower. Visit

www.WilsonElectronics.com

to find test mode function

for your particular cell phone or see page 7.

Run the Outside Antenna cable to the Signal Booster and attach it to3.

the connector labeled “Outside Antenna” on the Signal Booster. Run

the Inside Antenna cable to the Signal Booster and attach it to the

connector labeled “Inside Antenna” on the Signal Booster (see page

7 for more information on running cable). Lightning Surge Protection

is recommended for all in-building installations (see page 6).

Select a location for the Inside Antenna, preferably in the center of4.

where the signal needs to be amplified (see page 8). A minimum

separation distance of 20 vertical feet is necessary for operation. If

the inside coverage is not sufficient you may need as much as 75 feet

of horizontal separation. See installation diagram on pages 3 & 4.

Before powering up the Signal Booster, verify that both the Outside5.

Antenna and the Inside Antenna are connected and check that

all connections are tight (see page 9). Note: Be careful when

plugging the connectors in so as not to bend the center pins on the

connectors.

The Signal Booster has been packaged with the gain control knobs6.

adjusted to the highest gain position. If one or both of the lights are

not green please refer to pages 10 &11.

Quick Install Overview

See Installation Diagram on pages 3 & 4. Contact Wilson Electronics

Technical Support Team with any questions at 866-294-1660.

1 2 5 6

*Requires N-Male to F-Female adapter/converter (971128)

Appearance of device and accessories may vary.

Warning: Connecting the Signal Booster directly to a cell phone with

use of an adapter will damage the cell phone and/or the

Signal Booster.

Wilson® Electronics recommends that all AC power

supplies for home electronics be plugged into a

Surge Protector Power Strip.

3Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660

or email: [email protected]. Hours: 7 am to 6 pm MST.

Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660

or email: [email protected]. Hours: 7 am to 6 pm MST.

Typical Installation

Signal

Booster

Lightning

Surge Protector

(Recommended)

Outside

Antenna

(Wide Band

Antenna option

shown)

Inside Panel

Antenna

AG DB Pro Installation Diagram

Inside Panel

Antenna

Before Getting Started

This guide will help you properly install your Wilson Electronics Signal

Booster. It is important to read through all of the installation steps

for your particular application prior to installing any equipment.

Read through the instructions, visualize where all the equipment will

need to be installed and do a soft installation before mounting any

equipment.

Contact Wilson Electronics Technical Support Team with any

questions at: 866-294-1660.

2-way/3-way/

4-way splitter

(if using multiple

Inside Antennas)

(Optional third

antenna for

additional

coverage).

Null Zone: The area under the

Outside Antenna, where the

Outside Antenna radiates the

least.

Note: The Inside Panel Antenna

may be mounted on the wall

directly under the Outside

Antenna if 20 feet of vertical

separation can be maintained.

The preferred method for the best

coverage, place the antenna in

the ceiling.

Note: A Lightning Surge Protector

is recommended for all building

installations (sold separately). Make

sure the protector is installed in line

between the Outside Antenna and

the Signal Booster.

Surge Protector

Powerstrip

Power

Supply

(Optional

second

antenna for

additional

coverage).

5Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660

or email: [email protected]. Hours: 7 am to 6 pm MST.

Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660

or email: [email protected]. Hours: 7 am to 6 pm MST.

Reasons for Weak Cellular Signals

Anyone who uses a cell phone or cellular data card knows the frustration

of not being able to connect to or maintain a strong cellular signal. When

this occurs, it is generally due to one of two reasons:

Location of the Nearest Cell Tower – Cell towers are situated to1.

provide broad coverage; however, there are many areas in which

signal strength may be reduced by topographic features or by local

government restrictions on the height or placement of the towers

themselves. Rural areas generally have fewer cell towers than urban

regions.

Natural and Man-Made Obstructions – Signal strength can also2.

be negatively affected by trees, hills, weather, buildings, and other

obstructions. You may be relatively close to a cell tower but still unable

to make a call. This often occurs in homes, offices and other buildings

in which stucco, concrete or metal walls may block the signal.

The Signal Booster works with two antennas. The Inside Antenna

communicates with your cellular device and the Outside Antenna

communicates with the cell tower. The Outside Antenna receives the cell

tower signal and sends it through the cable to the Signal Booster, where it

is amplified and re-transmitted much stronger through the Inside Antenna

into the room. When the Inside Antenna picks up a signal from your cellular

device, the Signal Booster amplifies that signal and transmits it through

the cable to the Outside Antenna and back to the cell tower. (Note: The

Signal Booster will only operate if there is an adequate signal to amplify.)

Installing Lightning Protection

(sold separately)

Note: Use the directions included with your choice of antenna,

the instructions here are meant for the Wide Band Antenna option

shown above. The antenna should be mounted as shown in the

illustration above. The included mounting bracket is adjustable and will

accommodate pipe diameters from 1.25” to 2” (pipe sold separately

part# 901117). Mount the antenna so that there is at least 3 feet of

clearance in all directions around it. Position the antenna so that it has

an unobstructed line of sight to the cell tower’s strongest signal. Make

sure the antenna is not pointing across your own roof or at the Inside

Antenna as this will cause the oscillation (feedback) protection circuitry

to shut down the Signal Booster (see page 10).

Cell Tower

Drip hole on bottom

Cell Tower

Wide Band Antenna option shown

Outside Antenna Installation (Included in some kits)

Warning: Lightning protection is recommended for all installations

(sold separately part# 859988). Take extreme care to

ensure that neither you nor the antenna comes near any

electric power lines.

Install the Lightning Surge

Protector (LSP) close to the Signal

Booster. Attach the cable from

the Outside Antenna to the surge

protector, using a short length of low

loss cable; attach one end to the

LSP and the other to the Outside

Antenna connector on the Signal

Booster. Ensure the LSP is properly

grounded (ground wire not included).

Visit www.WilsonElectronics.com

or call 800-204-4104 to purchase.

Lightning

Surge Protector

(sold separately)

Signal Booster

Surge Protector

Power Strip recommended for all AC power supplies

Ground Wire

(not included)

To Outside

Antenna

To Inside

Antenna

Selecting a Direction for the Outside Antenna

Select a location on the roof of the building to install the Outside Antenna.

Use a cell phone in test mode to find the strongest signal from the cell

tower. To get the strongest signal possible, it is very important to set up your

Outside Antenna properly. The Inside and the Outside Antennas must be

mounted in such a way that they are able to pick up the best possible cellular

signal on the outside of the building and provide the best possible signal on

the inside of the building. Mount the Outside Antenna as high as possible

facing the cell tower in an area with the best possible signal coverage.

Note:

Never point the front of a directional antenna toward the Inside

Antenna. See Figure 1 & 2 on page 10.

7Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660

or email: [email protected]. Hours: 7 am to 6 pm MST.

Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660

or email: [email protected]. Hours: 7 am to 6 pm MST.

Mounting Tips for Running Outside

Antenna Cable

If you are mounting the Outside Antenna on the roof of your building, we

have found that it is easiest to run your cable underneath the down side of

your roof’s flashing. If you have satellite TV service installed at your home

or office, you may be able to follow the same route as the satellite TV cables

that are already running from the outside of your building to the inside. After

routing the cable, we recommend sealing any areas where the cable passes

into the building with silicone, cable bushings or other waterproof sealant to

keep your installation from leaking. If you are mounting the Outside Antenna

to the outside wall of your home or building, the simplest way is to run the

cable on the outside of the wall and attach it to the exterior of your home or

office. Then drill a hole through the wall where you want the cable to appear

on the inside of the building. Before drilling, make sure that there are no

electrical outlets, sewer or water pipes, or electrical wiring in the wall that you

are about to drill through as this could potentially harm you or damage the

building.

After drilling the required hole, run the cable through and seal it with silicone,

cable bushings or other waterproof sealant to enclose the hole that you have

created. In some instances, it may be possible to run the cable up into the

fascia of the attic overhang. In this circumstance, the cable will be accessible

in the attic for further routing.

When installing your Signal Booster’s Outside Antenna, aiming it towards

the best signal source from you service provider is important. The best way

of getting the strongest signal is to have one person on the roof to rotate

the Outside Antenna, which is connected to the Signal Booster. Turning the

Outside Antenna about 45 degrees at a time, while the second person is

watching the signal strength on the phone inside the building. This allows

you to read the signal strength from the cell tower. It is preferable to have

the phone in the test mode so the actual signal strength can be read, as

bars are not the most accurate. Go to www.WilsonElectronics.com for

help in finding the test mode for your phone. Always make sure the person

inside the building gives the signal time to arrive and register on the phone.

(Between 10-30 seconds for phone to reset the signal reading).

Signal readings usually appear as a negative number (for example, -86).

The closer you get to zero the stronger the signal. (See graph above).

-50dB -60dB -70dB -80dB -90dB -100dB -110dB

EXCELLENT GOOD POOR NO

SIGNAL

Signal Strength Figure

Cell Tower

Cell Signal

Outside

Wide Band

Antenna

Finding the Strongest Signal

Installing the Inside Antenna

(Included in some kits)

Select a location for the Inside Antenna, preferably in the center of where

the signal needs to be amplified. A minimum separation distance of 20

vertical feet is necessary for operation. If the inside coverage is not

sufficient you may need as much as 75 feet of horizontal separation. See

installation diagram on pages 3 & 4.

Ceiling

Rafters

Ceiling

Drywall

Inside

Antenna

In some cases, multiple Inside Antennas may be required if you have

multiple rooms with poor signal. A signal may be split by using a splitter

(sold separately). If using more than one Inside Antenna, a separation up

to 75 horizontal feet may be necessary between Inside Antennas. See

configuration on pages 3 & 4.

Wide Band

Panel Inside

Antenna

(Included in

some kits)

3-way

2-way

(sold separately)

Splitter Options:

Warning: An

Inside Antenna must

have a separation

distance from all

persons that is at

least 15 inches for

the panel antenna.

9Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660

or email: [email protected]. Hours: 7 am to 6 pm MST.

Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660

or email: [email protected]. Hours: 7 am to 6 pm MST.

Installing a Wilson Electronics Signal Booster

Select a location to install the Signal Booster that is away from excessive

heat, direct sunlight, moisture and that has proper ventilation. Do

not place the Signal Booster in an air-tight enclosure. Recommended

installation locations for in-building Signal Boosters are near a power

outlet and in a closet or on a shelf.

Note: It is important to have adequate air ventilation. Maintain at least 6

inches of clearance from surrounding objects.

Note: Be careful when plugging the connector in to avoid bending the

center pins on the connectors.

Run the Outside Antenna cable to the Signal Booster and attach it to the

connector labeled “Outside Antenna” on the Signal Booster. Run the

Inside Antenna cable to the Signal Booster and attach it to the connector

labeled “Inside Antenna” on the Signal Booster.

Powering up a Wilson Electronics

Signal Booster

Never point the front of a directional Outside Antenna toward the1.

Inside Antenna. See Figure 2 on page 10.

Ensure that both the Outside Antenna cable and the Inside Antenna2.

cable are connected to the Signal Booster and the connections are

tight before powering up the Signal Booster.

Plug the power supply into the Signal Booster input marked3. “POWER”

(carefully, to avoid damaging the center pin) and then into a Surge

Protector Power Strip.

If the Signal Booster does not have a green light, please see pages4.

10 & 11.

If you know that only one frequency band (800 or 1900) is available in5.

your coverage area (or going to be used), reduce the gain control on

the frequency band that is NOT in use to the lowest setting. This will

reduce the power consumption of the Signal Booster.

Using multiple Signal Boosters in one installation may cause6.

interference to the cell tower (except for In-Line Signal Booster part#

806215).

Contact Wilson Electronics Technical Support Team with any questions7.

at 866-294-1660 or email tech@wilsonelectronics.com. Technical

Support hours are 7 am to 6 pm MST.

Figure 1

Signal Booster

Outdoor

Antenna Inside Panel

Antenna

Figure 2

Signal Booster

Outdoor

Antenna

Inside Panel

Antenna

During installation mode the Signal Booster is resetting itself very quickly

to aid the installer. The Signal Booster is equipped with two indicator

lights, one for the 800 MHz band and the other for the 1900 MHz

band. For the first 15 minutes that the Signal Booster is plugged in, it is

programed for a test and alignment period. During this time, both lights

will do one of the following 4 things:

1. BLINKING GREEN

If the Signal Booster is blinking green, the Signal Booster is

operating properly. If you are happy with the coverage area in your

building, then you are done. Blinking will stop after the 15 minute

installation period.

2. BLINKING ORANGE

The Signal Booster is experiencing receiver overload. The Signal

Booster has protection shutoff circuits to prevent the disruption of

Understanding the Signal Booster Lights and

Troubleshooting

Note: If after the initial 15 minutes you are not done with the

installation, the Signal Booster can be reset and enter installation mode

again by disconnecting and reconnecting the power supply from the

Signal Booster.

11Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660

or email: [email protected]. Hours: 7 am to 6 pm MST.

Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660

or email: [email protected]. Hours: 7 am to 6 pm MST.

cell towers. If one or both lights are blinking orange, this indicates

that the Signal Booster has shut down due to close proximity to a

cell tower. First, turn down the gain control on the band that is

blinking until you get a blinking green light. The Signal Booster

is now working with reduced gain. If the gain is not adequate for

good coverage, you will need to turn the gain to maximum and

then turn the Outside Antenna away from the cell tower until the

light turns to blinking green. If the Signal Booster will not respond,

turn the gain down 5 dB and move the Outside Antenna. Continue to

adjust the gain and the Outside Antenna position until the light turns

blinking green. Contact Wilson Electronics Technical Support Team

for assistance:

866-294-1660.

3. SOLID RED

If either of the two lights on the Signal Booster are solid red, this

indicates that the Signal Booster has shut down on that frequency

to prevent an oscillation (feedback). First, make sure that all the

connections are tight. Then reduce the gain of the Signal Booster

in small increments by rotating the gain control, counter-

clockwise, waiting 5 seconds between each adjustment for the

Signal Booster to reset. Continue this adjustment until the light

turns blinking or solid green. When you are turning down the

gain, you are reducing the inside coverage area. If the amount of

coverage area is sufficient for your needs and the light is green the

installation is complete. If the coverage area is not large enough, it

is necessary to increase the separation distance of the antennas

by moving them horizontally or vertically farther apart, or both.

Then increase the gain until the red light comes on, and then

slightly keep decreasing the gain until the green or blinking

green light appears. If after separating the antennas your coverage

area is still too small, contact Wilson Electronics Technical Support

Team for assistance:

866-294-1660.

If your installation takes longer than 15 minutes, it is possible to re-

enter the installation mode by disconnecting and reconnecting the

power supply from the Signal Booster.

4. SOLID GREEN

The indicator lights on the Signal Booster will be a solid green after

the first 15 minute installation period and the unit is powered up and

working properly.

Warnings & Recommendations

Warning: The directional antenna must always be located so the

back or side points to the Inside Antenna. Never point the

front of the Outside Antenna toward the Inside Antenna –

this is to prevent oscillation.

Warning: Connecting the Signal Booster directly to the cell phone with

use of an adapter may damage the cell phone.

Warning: Use only the power supply provided in this package. Use

of a non-Wilson Electronics product may damage your

equipment.

Warning: RF Safety: FCC regulations require that any fixed Outside

Antenna used with this Signal Booster may not have gain

(less cable loss) that exceeds 15 dBi and must be located

at least 30 inches from all people. Inside Antennas must

not exceed 7 dBi gain (less cable loss) in the 800 MHz

band or 10 dBi gain (less cable loss) in the 1900 MHz

band and must be located at least 8 inches from all people.

Warning: Verify that both the Outside Antenna and the Inside

Antenna are connected to the Signal Booster before

powering up the Signal Booster.

Recommendation: Lightning Surge Protection is recommended for all

in-building installations.

13Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660

or email: [email protected]. Hours: 7 am to 6 pm MST.

Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660

or email: [email protected]. Hours: 7 am to 6 pm MST.

30-Day Money-Back Guarantee

All Wilson Electronics products are protected by Wilson Electronics 30-day

money-back guarantee. If for any reason the performance of any product is not

acceptable, simply return the product directly to the reseller with a dated proof of

purchase.

1-Year Warranty

Wilson Electronics Signal Boosters are warranted for one (1) year against

defects in workmanship and/or materials. Warranty cases may be resolved by

returning the product directly to the reseller with a dated proof of purchase.

Signal Boosters may also be returned directly to the manufacturer at the

consumer’s expense, with a dated proof of purchase and a Returned Material

Authorization (RMA) number supplied by Wilson Electronics. Wilson Electronics

shall, at its option, either repair or replace the product. Wilson Electronics

will pay for delivery of the repaired or replaced product back to the original

consumer if located within the continental U.S.

This warranty does not apply to any Signal Booster determined by Wilson

Electronics to have been subjected to misuse, abuse, neglect, or mishandling

that alters or damages physical or electronic properties.

RMA numbers may be obtained by phoning Technical Support at 866-294-1660.

Disclaimer : The information provided by Wilson Electronics, Inc. is

believed to be complete and accurate. However, no responsibility is assumed

by Wilson Electronics, Inc. for any business or personal losses arising from its

use, or for any infringements of patents or other rights of third parties that may

result from its use.

This device complies with Part 15 of FCC rules. The transaction is subject to two

conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired

operation. Changes or modifications not expressly approved by Wilson Electronics could

void the authority to operate this equipment.

One or more of the following U.S. Patent numbers may apply to the Signal Booster in this

product – D596,614; D596,615; D563,381;7,729,669; 7,486,929; 7,729,656; 7,409,186;

7,783,318; 7,684,838; 12,714,994.

About Wilson Electronics

Wilson Electronics, Inc. has been a leader in the wireless communications

industry for over 40 years. The company designs and manufactures Signal

Boosters, antennas and related components that significantly improve

cellular telephone signal reception and transmission in a wide variety

of applications, both mobile and in-building. With extensive experience

in antenna and Signal Booster research and design, the company’s

engineering team uses a state of the art testing laboratory, including an

anechoic chamber and network analyzers, to fine-tune antenna designs

and performance. For its Signal Boosters, Wilson Electronics uses a double

electrically insulated RF enclosure and cell tower simulators for compliance

testing.

Wilson Electronics Signal Boosters feature patented Smart Technology ™

that enables them to automatically adjust their power based on cell tower

requirements. By detecting and preventing oscillation (feedback), signal

overload and interference with other users, these Smart Technology ™

Signal Boosters improve network cell phone areas without compromising

carrier systems. All products are engineered and assembled in the

company’s 55,000-square-foot headquarters in St. George, Utah. Wilson

Electronics has product dealers in all 50 states as well as in countries

around the world.

Signal Booster Specifications

IC: 4726A-271265

FCC ID: PWO271265

DB Pro

Specifications

Model Number 271265

Antenna connectors F-Female

Antenna impedance 75 ohms

Dimensions 6.5 x 4.5 x 1.75 inch

(16.5 x 11.4 x 4.4 cm)

Weight 0.47 lbs (0.213 kg)

Frequency 824-894 MHz / 1850-1990 MHz

1Passband Gain (nominal)

800 MHz * 1900 MHz 62 / 65 dB

220 dB Bandwidth (nominal) Downlink

800 MHz 45 MHz

1900 MHz 88 MHz

Power Output 800 MHz 1900 MHz

Power output for single cell phone (uplink) 30.8 dBm 30.5 dBm

Power output for single received channel (downlink) 26.0 dBm 25.2 dBm

3Power output for multiple transmitted channels (uplink) Maximum Power

The maximum power is reduced

by the number of channels: Number of channels 800 MHz 1900 MHz

2 24.0 dBm 21.3 dBm

3 20.5 dBm 17.8 dBm

4 18.0 dBm 15.3 dBm

5 16.0 dBm 13.3 dBm

6 14.5 dBm 11.8 dBm

4Power output for multiple received channels (downlink) Maximum Power

The maximum power is reduced

by the number of channels: Number of channels 800 MHz 1900 MHz

2 24.8 dBm 23.7 dBm

3 21.3 dBm 20.2 dBm

4 18.8 dBm 17.7 dBm

5 16.8 dBm 15.7 dBm

6 15.3 dBm 14.2 dBm

Noise Figure (typical downlink/uplink) 3.5 dB nominal / 6 dB nominal

Isolation > 90 dB

Power Requirements 110-240 V AC, 50-60 Hz, 8 W

Notes:

1. Nominal gain is the maximum gain at any frequency in the passband.

2. Nominal bandwidth is the difference between two frequencies that are adjacent to the passband where the amplification is 20 dB lower than the passband

amplification. One of the frequencies is lower than the passband and the other is higher.

3. The Manufacturer’s rated output power of this equipment is for single carrier operation. For situations when multiple carrier signals are present, the rating

would have to be reduced by 3.5 dB, especially where the output signal is re-radiated and can cause interference to adjacent band users. This power

reduction is to be by means of input power or gain reduction and not by an attenuator at the output of the device.

4. The maximum power for 2 or more simultaneous signals will be reduced by 6 dB every time the number of signals is doubled.

3301 East Deseret Drive, St. George, UT 84790

For additional Technical Support visit www.WilsonElectronics.com

or email at: [email protected]

Phone: 866-294-1660 Local: 435-673-5021 Fax: 435-656-2432

www.twitter.com/WilsonCellular www.facebook.com/WilsonCellular

AIG #110892_Rev04_11.22.11

Table des matières

Autres manuels Wilson Electronics Extenseur

Wilson Electronics

Wilson Electronics 460008 Manuel utilisateur

Wilson Electronics

Wilson Electronics weBoost DRIVE 4G-X 470510R Manuel utilisateur

Wilson Electronics

Wilson Electronics weboost Drive Reach OTR Guide d'installation

Wilson Electronics

Wilson Electronics Sleek 4G Manuel utilisateur

Wilson Electronics

Wilson Electronics WILSON PRO 1050 Manuel utilisateur

Wilson Electronics

Wilson Electronics 2B1216 Manuel utilisateur

Wilson Electronics

Wilson Electronics Tri-Band 4G-C Manuel utilisateur

Wilson Electronics

Wilson Electronics WILSON PRO 4000 Manuel utilisateur

Wilson Electronics

Wilson Electronics Weboost AM100-PRO Manuel utilisateur

Wilson Electronics

Wilson Electronics 271265 Manuel utilisateur

Wilson Electronics

Wilson Electronics SIGNALBOOST 811210 Manuel utilisateur

Wilson Electronics

Wilson Electronics Sleek Manuel utilisateur

Wilson Electronics

Wilson Electronics IoT 5-Band Manuel utilisateur

Wilson Electronics

Wilson Electronics Signal 4G 460019 Manuel utilisateur

Wilson Electronics

Wilson Electronics weboost DRIVE REACH OTR FLEET Manuel utilisateur

Wilson Electronics

Wilson Electronics AG Pro 70 Manuel utilisateur

Wilson Electronics

Wilson Electronics weBoost Connect 4G-X 471104R Manuel utilisateur

Wilson Electronics

Wilson Electronics 801105 Manuel utilisateur

Wilson Electronics

Wilson Electronics Signal 4G SmarTech III Manuel utilisateur

Wilson Electronics

Wilson Electronics PRO 1100 Manuel utilisateur

Wilson Electronics

Wilson Electronics Mobile 4G SmarTech III 460108 Manuel utilisateur

Wilson Electronics

Wilson Electronics weBoost DRIVE X 475021R Manuel utilisateur

Wilson Electronics

Wilson Electronics weboost Home Complete 530045 Manuel utilisateur

Wilson Electronics

Wilson Electronics DT4G 460101 Manuel utilisateur

Manuels Extenseur populaires d'autres marques

SY HDBT-60T Manuel utilisateur

Appsys ProAudio

Appsys ProAudio ADX-16 Manuel utilisateur

Atlona

Atlona RS232 Manuel utilisateur

IDK

IDK OPF-TH1000-A Manuel utilisateur

Enable-IT

Enable-IT 824WP Manuel utilisateur

Worx

Worx Landroid RadioLink WA0864 Fiche technique

TP-Link

TP-Link TL-WA730RE Manuel utilisateur

Camplex

Camplex CMX-HDMI-SFPL Manuel utilisateur

SC&T

SC&T HE03-4K Manuel utilisateur

Marmitek

Marmitek MegaView70 Manuel utilisateur

Samsung

Samsung SCS-26UC4 Manuel utilisateur

Foxun

Foxun SX-GES24 Manuel utilisateur

MuxLab

MuxLab 500771 Manuel utilisateur

foxunhd

foxunhd SX-AEX01 Manuel utilisateur

TERK Technologies

TERK Technologies LFIRX2 Manuel utilisateur

Devolo

Devolo Audio Extender Manuel

Edimax

Edimax EW-7438RPn V2 Manuel utilisateur

Shinybow USA

Shinybow USA SB-6335T5 Manuel utilisateur