Wilson Electronics 2B1216 Manuel utilisateur

Contents

Before Getting Started............................1

Accessories and Antenna Options . . . . . . . . . . . . . . . . . . 1

Quick Installation Overview ........................2

Installation Diagram..............................2

Installing the External Adapter......................3

Installing the Outside Antenna......................3

Installing a Wilson Electronics Signal Booster. . . . . . . . . . 3

Powering Up a Wilson Electronics Signal Booster . . . . . . 3

In-Building Installation ............................4

Warnings and Recommendations ...................5

Guarantee and Warranty ..........................6

Signal Booster Specifications . . . . . . . . . . . . . .Back Cover

GSM High Power

Direct Connect

800/1900 MHz

Smart Technology ™

Signal Booster

Note: This manual contains important safety and operating information.

Please read and follow the instructions in this manual. Failure to do so could

be hazardous and result in damage to your Signal Booster.

Appearance of device and accessories may vary.

1Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660

or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.

Inside this Package

Accessories & Antenna Options (sold separately)

Before Getting Started

This guide will help you properly install your Wilson Electronics Signal Booster. It is impor-

tant to read through all of the installation steps for your particular application prior to

installing any equipment. Read through the instructions, visualize where all the equipment

will need to be installed and do a soft installation before mounting any equipment. For further

assistance please call our Wilson Electronics Technical Support Team: 866-294-1660.

Installation Instructions for the Following Wilson

Electronics Signal Booster:

Model # 2B1216 FCC: PWO2B1216 IC:4726A-2B1216

The term “IC” before the radio certification number only signifies that Industry Canada

technical specifications were met.

NMO

Mount

(301104)

Magnet

Mount

(301125)

Trucker

Mount

(301101)

Mini

Magnet

(301126)

800/1900

MHz Omni-

Directional

Antenna

(301202)

Lightning

Surge Protector

(859902)

Marine

Antenna

(301130)

700/2700 MHz Wide-Band Directional

Antenna (304475)

Wide Band Directional Antenna

(adapters may be required)

Omni Directional Antennas (adapters may be required)

7V AC/DC

Power Supply

(859986)

GSM

High Power

Signal Booster

6’ RG174

Cable

(951141)

Accessory

(adapters may be required)

Appearance of device and accessories may vary.

Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660

or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.

Select a location to install the Signal Booster that is away from excessive heat, direct1.

sunlight, moisture and that has proper ventilation. Do not place the Signal Booster in

an air-tight enclosure.

Select a location on the top of the structure to install the Outside Antenna. Use a cell2.

phone

in test mode to find the strongest signal from the cell tower. Visit

www.WilsonElectronics.com to find test mode function for your particular cell phone.

Run the Outside Antenna cable to the Signal Booster and attach it to the connector3.

labeled “Outside Antenna.”

An external adapter is required to connect the cell phone or cellular data card to the4.

Signal Booster. The external adapter plugs into the included antenna extension cable

and directly into a socket on the cellular device. Run the extension cable from the

external adapter and attach it to the connector labeled “Inside Antenna” on the Signal

Booster.

Note: Be careful when plugging the connector in so as not to bend the center pins on

the connectors. Ensure all cables have a tight connection.

Before powering up the Signal Booster verify that both the Outside Antenna and the5.

Inside Antenna are connected and check that all connections are tight. An AC surge

protector is recommended for all installations (not included).

Quick Installation Overview

The following steps provide a summary of the Signal Booster/antenna installation process.

Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660.

Powerstrip Surge Protector

Power Supply

GSM Hi-Power

Signal Booster

Cellular Modem

Mini-Magnet

Antenna

Installation Diagram

(Figure 1)

NOTE: It is very important to power your Signal Booster using a surge protected AC Power Strip with at least a 1000 Joule rating.

Failure to do this will void your warranty in the event of a power surge or lightning strike.

3Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660

or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.

How it Works

Wilson Electronics Signal Boosters are bi-directional devices that deliver service levels

consistent with what would be expected in areas of high cell network coverage. They

amplify a weak or shadowed signal in mobile, marine, M2M and in-building applications.

When using a Wilson Electronics Signal Booster in conjunction with Wilson Electronics

antennas, the Outside Antenna will collect the cell tower signal and send it through the

cable to the Signal Booster. Cell phones and cellular data cards then communicate with

the improved signal. When a cellular device transmits, the signal is amplified by the Signal

Booster and transmitted back to the cell tower through the Outside Antenna.

Installing the External Adapter

An external adapter is required to connect the cell phone or cellular data card to the Signal

Booster. The external adapter is cell phone/data card-specic and may be purchased

through a local retailer. Refer to Wilson Electronics Adapter Guide to identify the correct

adapter for your cell phone or cellular data card. The adapter guide is available through a

local retailer or at www.WilsonElectronics.com. The external adapter plugs into the antenna

extension cable (included) and directly into a socket on the cellular device.

The external adapter and the extension cable are long enough to reach the Signal Booster

location. This allows for ease and convenience of use. Run the extension cable from the

external adapter and attach it to the connector labeled “Inside Antenna” on the Signal

Booster.

NOTE: Depending on your specific cell phone, the adapter socket may be located beneath

a rubber plug.

Installing a Wilson Electronics Outside Antenna

Select a location on the top of the structure to install the Outside Antenna that has the most

unobstructed line of sight to the cell tower. To obtain maximum performance, the antenna

should point toward the cell tower. Follow the instructions included with the Outside

Antenna and the RF Safety Warning (page 5). Run the cable from the Outside Antenna and

attach it to the connector labeled “Outside Antenna” on the Signal Booster.

Lightning protection is recommended for all stationary installations (sold separately). Take

extreme care to ensure neither you nor the antenna come in contact with any electrical power

lines. Ensure there are at least three feet of clearance in all directions surrounding the

antenna.

Installing a Wilson Electronics Signal Booster

Select a location to install the Signal Booster that is away from excessive heat, direct

sunlight, moisture and that has proper ventilation. Ensure the Signal Booster is installed

within six feet of where the cell phone or cellular data card will be used (to accommodate

the six-foot adapter extension cable).

Run the cable from the Outside Antenna and attach it to the connector labeled “Outside

Antenna” on the Signal Booster.

Powering up a Wilson Electronics Signal Booster

Ensure that both the Outside Antenna cable and the adapter cable are connected to the1.

Signal Booster before powering up the Signal Booster.

Connect the power supply to the power input labeled “7V DC” on the Signal Booster.2.

Plug the power supply into a powerstrip surge protector (recommended).

The indicator light on the side of the Signal Booster will be GREEN when the unit is3.

powered up and working properly.

If the light is off, ensure power supply connections are tight.4.

Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660

or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.

Warning: Use only a Wilson Electronics power

supply. Use of a non-Wilson Electronics product

could damage your equipment. It is very

important to power your Signal Booster using a

surge protected AC Power Strip with at least a

1000 Joule rating.

Warning: Verify that both the Outside

Antenna and the adapter extension cable

are connected to the Signal Booster before

powering up the Signal Booster.

Testing a Wilson Electronics Signal Booster

To test your Signal Booster, go to a weak signal area where your cell phone registers only

1-2 bars without the Signal Booster turned on. Then, connect the Signal Booster to the

phone and you should see a signal improvement of 2 or more bars.

Note: Many phones take up to 30 seconds to reset the bar indicator.

In-Building Installation

This is the recommended install for in-building use.

Contact our Technical Support Team for more information at:

866-294-1660 or [email protected]

Lightning

Surge Protector

(sold separately)

GSM High Power

Powerstrip Surge

Protector

Wide Band

Directional Antenna

Point toward cell tower

Power Supply

Connect to cell

phone or data

card

To Outside Antenna

Carefully insert the power cable.

5Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660

or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.

Warnings and Recommendations

Warning: Verify that both the Outside Antenna and the adapter extension cable are

connected to the Signal Booster before powering up the Signal Booster.

Warning: Use only the power supply provided in this package. Use of a non-WIlson

Electronics products may damage your equipment.

Warning: RF Safety: All outside fixed antennas may not have gain that exceeds

15 dBi (less cable loss) and must be located at least 56 inches from all

people. All antennas shown on page one meet these requirements.

Lightning protection is recommended for all in-building installations.

It is recommended that outside building antenna installations comply with relevant electrical

codes.

NOTE: The aluminum casing of a Wilson Electronics Signal Booster will adjust very quickly

to the ambient temperature of its environment. For example, in the summer, when the

inside of a enclosure can be extremely hot, the Signal Boosters’ optional fan will come on

to prevent overheating. The casing will be hot to the touch, similar to a metal door handle or

a steering wheel. Such high temperatures will not damage the Signal Booster, nor do they

pose a fire risk to the structure. As recommended in these instructions, install the Signal

Booster in a location with adequate ventilation. Keep the area free of items that could block

air flow to the Signal Booster. Do not install the Signal Booster in direct sunlight.

This device complies with Part 15 of FCC rules. The operation is subject to two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation. Changes or

modifications not expressly approved by Wilson Electronics could void the authority to operate

this equipment.

About Wilson Electronics

Wilson Electronics, Inc. has been a leader in the wireless communications industry for over

40 years. The company designs and manufactures Signal Boosters, antennas and related

components that significantly improve cellular telephone signal reception and transmission

in a wide variety of applications, mobile, in-building, and M2M.

With extensive experience in antenna and Signal Booster research and design, the

company’s engineering team uses a state-of-the-art testing laboratory, including an

anechoic chamber and network analyzers, to fine-tune antenna designs and performance.

For its Signal Boosters, Wilson Electronics uses a double electrically shielded RF

enclosure and cell tower simulators for compliance testing.

Wilson Electronics Signal Boosters feature patented Smart Technology ™ that enables

them to automatically adjust their power based on cell tower requirements. By detecting

and preventing oscillation feedback, signal overload and interference with other users,

these Smart Technology ™ Signal Boosters improve network cell phone areas without

compromising carrier systems. All products are engineered and assembled in the

company’s 55,000-square-foot headquarters in St. George, Utah. Wilson Electronics has

product dealers in all 50 states as well as in countries around the world.

Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660

or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.

30-Day Money-Back Guarantee

All Wilson Electronics products are protected by Wilson Electronics 30-day money-

back guarantee. If for any reason the performance of any product is not acceptable,

simply return the product directly to the reseller with a dated proof of purchase.

1-Year Warranty

Wilson Electronics Signal Boosters are warranted for one (1) year against defects

in workmanship and/or materials. Warranty cases may be resolved by returning the

product directly to the reseller with a dated proof of purchase.

Signal Boosters may also be returned directly to the manufacturer at the consumer’s

expense, with a dated proof of purchase and a Returned Material Authorization

(RMA) number supplied by Wilson Electronics. Wilson Electronics shall, at its

option, either repair or replace the product. Wilson Electronics will pay for delivery of

the repaired or replaced product back to the original consumer if located within the

continental U.S.

This warranty does not apply to any Signal Booster determined by Wilson Electronics

to have been subjected to misuse, abuse, neglect, or mishandling that alters or

damages physical or electronic properties.

Failure to use a surge protected AC Power Strip with at least a 1000 Joule rating will

void your warranty.

RMA numbers may be obtained by contacting Technical Support at 866-294-1660.

Disclaimer : The information provided by Wilson Electronics, Inc. is believed to

be complete and accurate. However, no responsibility is assumed by Wilson

Electronics, Inc. for any business or personal losses arising from its use, or for any

infringements of patents or other rights of third parties that may result from its use.

AIG #111044_Rev02_02.16.12

3301 East Deseret Drive, St. George, UT 84790

For additional Technical Support visit www.WilsonElectronics.com

or email at: [email protected]

Phone: 866-294-1660 Local: 435-673-5021 Fax: 435-656-2432

www.twitter.com/WilsonCellular www.facebook.com/WilsonCellular

Signal Booster Specifications

Dual-Band

Model Number / Part Number 2B1216

Connectors FME Female

Impedance (input/output) 50 ohms

Dimensions 6.12 x 3.5 x 2.0

Frequency 824-894 MHz / 1850-1990 MHz

1Passband Gain (nominal) 800 MHz

Typical / Maximum

1900 MHz

Typical / Maximum

Uplink 11 dB / 13 dB 11 dB / 13 dB

Downlink 11 dB / 13 dB 13 dB / 15 dB

220 dB Bandwidth (nominal) 800 MHz

Typical / Maximum

1900 MHz

Typical / Maximum

U p l i n k 44 MHz / 48 MHz 76 MHz / 84 MHz

Downlink 45 MHz / 50 MHz 87 MHz / 96 MHz

3Power output for single cell phone (uplink) dBm 800 MHz 1900 MHz

EDGE 36.2 35.0

GSM 35.8 34.4

CDMA 34.7 33.8

WCDMA 35.1 33.7

4Power output for multiple received

channels (uplink) dBm. The

maximum power is reduced by the

number of channels:

Number of

channels

Maximum Power3

800 MHz 1900 MHz

2 22.1 29.6

3 18.6 26.1

4 16.1 23.6

5 14.2 21.6

6 12.6 20.0

Noise Figure (typical) 3 dB nominal

Isolation > 30 dB

Power Requirements 7V DC, 3A

Notes:

1. Nominal gain is the maximum gain at any frequency in the passband.

2. Nominal bandwidth is the difference between two frequencies that are adjacent to the passband where the amplification is 20 dB

lower than the passband amplification. One of the frequencies is lower than the passband and the other is higher.

3. The Manufacturer’s rated output power of this equipment is for single carrier operation. For situations when multiple carrier

signals are present, the rating would have to be reduced by 3.5 dB, especially where the output signal is re-radiated and can

cause interference to adjacent band users. This power reduction is to be by means of input power or gain reduction and not by an

attenuator at the output of the device.

4. The maximum power for 2 or more simultaneous signals will be reduced by 6 dB every time the number of signals is doubled.

Table des matières

Autres manuels Wilson Electronics Extenseur

Wilson Electronics

Wilson Electronics WilsonPro A500 Manuel utilisateur

Wilson Electronics

Wilson Electronics DT4G 460101 Manuel utilisateur

Wilson Electronics

Wilson Electronics PRO 1100 Manuel utilisateur

Wilson Electronics

Wilson Electronics Tri-Band 4G-V Manuel utilisateur

Wilson Electronics

Wilson Electronics weBoost Drive Reach RV Manuel utilisateur

Wilson Electronics

Wilson Electronics Signal 3G Manuel utilisateur

Wilson Electronics

Wilson Electronics WILSON PRO 4000R Manuel utilisateur

Wilson Electronics

Wilson Electronics weboost Drive Reach OTR Guide d'installation

Wilson Electronics

Wilson Electronics 271265 Manuel utilisateur

Wilson Electronics

Wilson Electronics weboost DRIVE REACH OTR FLEET Manuel utilisateur

Wilson Electronics

Wilson Electronics PRO 70 PLUS SELECT Manuel utilisateur

Wilson Electronics

Wilson Electronics Signal 4G SmarTech III Manuel utilisateur

Wilson Electronics

Wilson Electronics weBoost DRIVE SLEEK Manuel utilisateur

Wilson Electronics

Wilson Electronics WEBOOST DRIVE X OTR Manuel utilisateur

Wilson Electronics

Wilson Electronics Sleek Manuel utilisateur

Wilson Electronics

Wilson Electronics AG Pro 75 Manuel utilisateur

Wilson Electronics

Wilson Electronics AG Pro 70 Manuel utilisateur

Wilson Electronics

Wilson Electronics 277280 Manuel utilisateur

Wilson Electronics

Wilson Electronics weboost Office 100 Manuel utilisateur

Wilson Electronics

Wilson Electronics 463005 Manuel utilisateur

Wilson Electronics

Wilson Electronics 801105 Manuel utilisateur

Wilson Electronics

Wilson Electronics weboost DRIVE REACH OTR FLEET Manuel utilisateur

Wilson Electronics

Wilson Electronics weboost Office 200 Manuel utilisateur

Wilson Electronics

Wilson Electronics weBoost DRIVE 4G-X OTR 470210R Manuel utilisateur

Manuels Extenseur populaires d'autres marques

SY HDBT-60T Manuel utilisateur

Appsys ProAudio

Appsys ProAudio ADX-16 Manuel utilisateur

Atlona

Atlona RS232 Manuel utilisateur

IDK

IDK OPF-TH1000-A Manuel utilisateur

Enable-IT

Enable-IT 824WP Manuel utilisateur

Worx

Worx Landroid RadioLink WA0864 Fiche technique

TP-Link

TP-Link TL-WA730RE Manuel utilisateur

Camplex

Camplex CMX-HDMI-SFPL Manuel utilisateur

SC&T

SC&T HE03-4K Manuel utilisateur

Marmitek

Marmitek MegaView70 Manuel utilisateur

Samsung

Samsung SCS-26UC4 Manuel utilisateur

Foxun

Foxun SX-GES24 Manuel utilisateur

MuxLab

MuxLab 500771 Manuel utilisateur

foxunhd

foxunhd SX-AEX01 Manuel utilisateur

TERK Technologies

TERK Technologies LFIRX2 Manuel utilisateur

Devolo

Devolo Audio Extender Manuel

Edimax

Edimax EW-7438RPn V2 Manuel utilisateur

Shinybow USA

Shinybow USA SB-6335T5 Manuel utilisateur