Westermo Viper 108 Manuel utilisateur

www.westermo.com

Viper 108 and 408

Managed 8-port Ethernet Switch

26641-2201

6641-2201

General information

Legal information

The contents of this document are provided “as is”. Except as required by applicable law,

no warranties of any kind, either express or implied, including, but not limited to, the

implied warranties of merchantability and fitness for a particular purpose, are made in

relation to the accuracy and reliability or contents of this document. Westermo reserves

the right to revise this document or withdraw it at any time without prior notice.

Under no circumstances shall Westermo be responsible for any loss of data or income or

any special, incidental, and consequential or indirect damages howsoever caused.

More information about Westermo can be found at the following Internet address:

www.westermo.com

License and copyright for included Free/Libre Open Source Software

This product includes software developed by third parties, including Free/Libre Open

Source Software (FLOSS). The specific license terms and copyright associated with the

software are included in each software package respectively. Please visit the product web

page for more information.

Upon request, the applicable source code will be provided. A nominal fee may be charged

to cover shipping and media. Please direct any source code request to your normal sales

or support channel.

46641-2201

Safety information

Before installation:

Read this manual completely and gather all information on the unit. Make sure that

you understand it fully. Check that your application does not exceed the safe operating

specifications for this unit.

This unit should only be installed by qualified personnel.

This unit should be built-in to an apparatus cabinet, or similar, where access is restricted

to service personnel only. The power supply wiring must be sufficiently fused, and if

necessary it must be possible to disconnect manually from all power supply. Ensure

compliance to national installation regulations. This unit relies on convection cooling.

Make sure that it is installed so that the ambient temperature is within the specified

temperature range, e.g. by avoiding obstruction of the airflow around the unit. Also

check chapter EN 45545-2 mounting notes.

The unit has no internal fuse and should be connected via an external fuse. The fuse

should be calculated in accordance with the rated current.

Before mounting, using or removing this unit:

Prevent access to hazardous voltage by disconnecting the unit from all power supply.

Warning

Do not open connected unit. Hazardous voltage may occur within this unit when

connected to power supply.

Before powering-up, a protective earthing conductor must be connected to the

protective earthing terminal and have a cross-sectional area of at least 1.5 mm².

Note that this unit can be connected to two different power sources.

Be aware of that the surface of this unit may become hot. When this unit is

operated at high temperatures, the External Surface of Equipment may exceed

Touch Temperature Limit according to EN/IEC/UL 60950-1.

To reduce the risk of fire:

1. Use only No. 21 AWG or larger power cable

2. Use only No. 26 AWG or larger telecommunication line cord.

6641-2201

Care recommendations

Follow the care recommendations below to maintain full operation of unit and to fulfill

the warranty obligations:

…This unit must not be operating with removed covers or lids.

…Do not attempt to dissassemble the unit. There are not any user serviceable

parts inside.

…Do not drop, knock or shake the unit. Rough handling above the specification

may cause damage to internal circuit boards.

…Do not use harsh chemicals, cleaning solvents or strong detergents to clean the

unit.

…Do not expose the unit to any kind of liquid (water, beverages, paint etc). The

unit is not waterproof. Keep the unit within the specified humidity levels.

…Do not use or store the unit in dusty, dirty areas, connectors as well as other

mechanical part may be damaged.

…Do not cover or bring mechanical force to the ventilation membrane on the

back of the unit.

If the unit is not working properly, contact the place of purchase, nearest Westermo

distributor office or Westermo Tech support.

Maintenance

No maintenance is required, as long as the unit is used as intended within the specified

conditions.

Product disposal.

This symbol means that the product shall not be treated as

unsorted municipal waste when disposing of it. It needs to

be handed over to an applicable collection point for recy-

cling electrical and electronic equipment.

By ensuring this product is disposed of correctly, you will

help to reduce hazardous substances and prevent potential

negative consequences to both environment and human

health, which could be caused by inappropriate disposal.

66641-2201

Simplified EU declaration of conformity

Hereby, Westermo declares that the equipment is in compliance with EU directives. The

full EU declaration of conformity and other detailed information are available at the

respective product page at www.westermo.com. .

Agency approvals and standards compliance

Type Approval / Compliance

EMC EN 61000-6-1, Immunity residential environments

EN 61000-6-2, Immunity industrial environments

EN 61000-6-3, Emission residential environments

EN 61000-6-4, Emission industrial environments

EN 50121-3-2, Railway applications - EMC: Rolling stock – Apparatus

EN 50121-4, Railway signalling and telecommunications apparatus

IEC 62236-4, Railway signalling and telecommunications apparatus

E-Mark, Road Vehicles, E1 no: 10 R - 047216*

Safety EN 60950-1, IT equipment

Environmental EN 50155 Railway applications - Electronic equipment used on rolling stock

EN 61373 – Railway applications – Rolling stock equipment. Shock and

vibration tests

IEEE 1478 – Environmental conditions for transit rail car electronic equipment

EN 50124-1 – Railway applications – Insulation coordination

IEC 60068-2-27, (shock 10 g. 11 ms), IEC 60068-2-64

Fire protection EN 45545-2, Fire protection on railway vehicles

FCC Part 15.105 Notice: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

… Reorient or relocate the receiving antenna

… Increase the separation between the equipment and receiver

… Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected

… Consult the dealer or an experienced radio/TV technician for help.

Note * _ Applicable only for 3641-6360

6641-2201

Type tests and environmental conditions

Phenomena Test Description Test levels

ESD EN 61000-4-2 Enclosure contact ± 6 kV (crit A)

Enclosure air ± 8 kV (crit A)

RF field AM modulated IEC 61000-4-3 Enclosure 20 V/m 80% AM (1 kHz),

80 – 2700 MHz (crit A)

10 V/m 80% AM (1 kHz),

2700 – 6000 MHz (crit A)

Fast transient EN 61000-4-4 Ethernet ports ± 2 kV (crit A)

Power port ± 2 kV (crit A)

Earth port ± 2 kV (crit A)

Surge EN 61000-4-5 Fault port ± 2 kV line to earth (crit A)

Ethernet ports ± 2 kV line to earth (crit A)

Power port ± 2 kV line to earth, ± 2 kV line to line

(crit A)

RF conducted EN 61000-4-6 Ethernet ports 10 V 80% AM (1 kHz), 0.15 – 80 MHz

(crit A)

Power port 10 V 80% AM (1 kHz), 0.15 – 80 MHz

(crit A)

Power frequency magnetic

field

EN 61000-4-8 Enclosure 1000 A/m 50 Hz

300 A/m 16.7 Hz, 60 Hz, DC (crit A)

Pulse magnetic field EN 61000-4-9 Enclosure 300 A/m (crit A)

Voltage dips and interruption EN 50155 DC power ports 10 ms interruption, 100 ms ±40% voltage

variation

Radiated emission CISPR 16-2-3

ANSI C63.4

(FCC part 15)

Enclosure Class B (30 – 6000 MHz)

Conducted emission CISPR 16-2-1 DC power port &

Ethernet ports

Class B

Dielectric strength EN 50155 Ethernet ports to other

isolated ports

707 VDC 1 min

Power & Fault port to

other isolated ports

2121 VDC 1 min

Temperature EN 60068-2-1

EN 60068-2-2

Operating –40 to +70ºC

Storage & Transport –50 to +85ºC

Humidity EN 60068-2-30 Operating 5 to 95% relative humidity

Storage & Transport 5 to 95% relative humidity

Altitude Operating 2000 m / 70 kPa

Reliability prediction (MTBF) MIL-HDBK- 217F Operating Ground Benign:

118 years @ 25ºC

116 years @ 40ºC

Service life Operating 10 year

Vibration, random simulated

long life

IEC 60068-2-64,

Cat. 1 class B

(EN 61373)

Not Operating Vertical: 7.9 m/s2

Transverse: 7.9 m/s2

Longitudinal: 7.9 m/s2

3 x 5 h

Vibration, random functional IEC 60068-2-64,

Cat. 1 class B

(EN 61373)

Operating Vertical: 1.0 m/s2

Transverse: 1.0 m/s2

Longitudinal: 1.0 m/s2

3 x 10 min

86641-2201

Phenomena Test Description Test levels

Shock, half sine pulses IEC 60068-2-27,

Cat. 1 class B

(EN 61373)

Operating Vertical: 50 m/s2

Transverse: 50 m/s2

Longitudinal: 50 m/s2

30 ms, 3 x 6 shocks

Shock, sawtooth IEC 60068-2-27,

Cat. 1 class B

(IEEE1478-2001)

Operating Vertical: 100 m/s2

Transverse: 100 m/s2

Longitudinal: 100 m/s2

11 ms, 3 x 6 shocks

Enclosure UL 94 Nickel coated zinc Flammability class V-1

Dimension W x H x D 175 x 100 x 50 mm

Weight 0.9 kg

Degree of protection IEC 529 Enclosure IP 65 when all ports are protected/

connected

Cooling Convection

Mounting Wall mounted

6641-2201

Description

Functional description

Viper is a range of switches consisting of two different function levels developed for

rail and industrial applications. To meet the environmental requirements from rail and

harsh industrial applications the switch has rugged M12 Ethernet connectors and full

metal housing. The switch fullfill IP65 degree of protection when all ports are protected/

connected. Our unique FRNT (Fast Recovery of Network Topology) technology is the

fastest protocol on the market to re-configure a network in the event of any failure of a

link or hardware. Real-time properties are implemented in the Viper108 and 408 in order

to achieve determinism for real time critical applications. The Viper-switches supports

QoS (Quality of Service) with four priority queues and strict priority scheduling as

well as HoL (Head of Line Blocking Prevention). All to assure that the data network is

deterministic.

10 6641-2201

Interface specifications

Power and fault relay port PWR

Rated voltage 24 to 110 VDC

Operating voltage 16.8 to 143 VDC (14.4 to 154 for 100 ms)

Rated current 140 mA @ 24 VDC

40 mA @ 110 VDC

Rated frequency DC

Inrush current, I2t Max 0.02 A2s @ 24 – 110 VDC

Startup current * 300 mA @ 16.8 VDC

Polarity Reverse polarity protected

Redundant power input No

Isolation to Connections X1 – X8 and to ground, 1500 VAC.

Fault relay belongs to the same isolation group as the power

supply lines (fault relay signals are also contained within

PWR).

Connection 4 pin male M12 connector with A-code

Connector size M12, recommended cable area 0.5 mm2 recommended

(minimum 0.25 mm2), cable dimensions depend on choice of

M12 connector

Shielded cable Not required, twisted pair is recommended

Fault relay resistance < 10 Ω

Operating voltage Up to 110 VDC

Max continuous current 250 mA

* If external power supply is used it must meet specified startup current.

M12 A-Coded

Power

Connector

Position Direction Description

1 U+ Positive supply voltage

2 Out Alarm relay (status) +

30 V Negative supply voltage

4 Out Alarm relay (status) –

Housing Shield Chassis of product (ground)

Autres manuels pour Viper 108

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Westermo Changer

Westermo

Westermo Viper-12 Series Manuel utilisateur

Westermo

Westermo U200 series Manuel utilisateur

Westermo

Westermo PSI-1010G-24V Manuel utilisateur

Westermo

Westermo Lynx DSS L205-S1-EX Manuel utilisateur

Westermo

Westermo Viper 20A Series Manuel utilisateur

Westermo

Westermo RedFox Industrial EX Series Manuel utilisateur

Westermo

Westermo SDW-500 Manuel utilisateur

Westermo

Westermo Viper 20A-PoE Series Manuel utilisateur

Westermo

Westermo Viper 12A-PoE Series Manuel utilisateur

Westermo

Westermo Lynx DSS L108-F2G-S2 EX Manuel utilisateur

Westermo

Westermo RedFox RFI-119-F4G-T7G Manuel utilisateur

Westermo

Westermo Lynx DSS L108-F2G-S2 EX Manuel utilisateur

Westermo

Westermo Lynx L106-S2 Manuel utilisateur

Westermo

Westermo Viper-TBN Series Manuel utilisateur

Westermo

Westermo RedFox 5528 Series Manuel utilisateur

Westermo

Westermo Viper-8 Series Manuel utilisateur

Westermo

Westermo PSI-010-FT2G-P8G Manuel utilisateur

Westermo

Westermo RedFox-5728-F4G-T24G-LV Manuel utilisateur

Westermo

Westermo Lynx DSS L108 Manuel utilisateur

Westermo

Westermo Lynx DSS L108-F2G-S2 EX Manuel utilisateur

Westermo

Westermo RedFox-5528-E-T28G-LV Manuel utilisateur

Westermo

Westermo Lynx 5500 Series Manuel utilisateur

Westermo

Westermo Viper 12A Series Manuel utilisateur

Westermo

Westermo Viper-120A-P8-HV Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur