Weil-McLain 78 Manuel utilisateur

This manual must only be used by a qualified heating installer/service

technician. Failure to comply could result in severe personal injury,

death or substantial property damage.

Part No. 550-1 1-705/0600

78 78

Boiler For Gas, Light Oil, Gas/Light Oil Fired Burners

Boiler Manual

• Installation

• Start-Up

• Maintenance

• Parts

Installer: Leave all documentation received with boiler and burner

with unit for future reference.

User: Boiler and burner must be installed and serviced by a

qualified service technician.

All manuals and user guides at all-guides.com

all-guides.com

Part No. 550-1 1-705

Weil-McLain 78 Boiler For Gas Light Oil Gas/Light Oil Fired Burners

Contents

1. Before Installing Boiler.............................................................. page 3

2. Set Packaged Boiler or Block Assembly in Place................ page 5

3. Assemble Block.......................................................................... page 6

4. Perform Hydrostatic Pressure Test....................................... page 12

5. Connect Water Boiler Piping.................................................. page 13

6. Connect Steam Boiler Piping................................................. page 15

7. Install Jacket ............................................................................. page 19

8. Pipe Tankless Heaters............................................................. page 19

9. Install Water Boiler Controls .................................................. page 20

10. Install Steam Boiler Controls ................................................. page 21

11. Connect Breeching and Venting Systems........................... page 23

12. Install Burner............................................................................. page 24

13. Wiring and Fuel Piping............................................................ page 24

14. Make Final Adjustments.......................................................... page 25

15. Data and Dimensions .............................................................. page 27

16. Parts............................................................................................ page 29

17. Ratings ....................................................................................... page 31

Warranty...................................................................................... Back Cover

Hazard Definitions

The following defined terms are used throughout this manual to bring attention to the presence of hazards of

various risk levels, or to important information concerning the life of the product.

Indicates presence of hazards that will cause severe personal injury, death or substantial

property damage if ignored.

Indicates presence of hazards that can cause severe personal injury, death or substantial

property damage if ignored.

Indicates presence of hazards that will or can cause minor personal injury, death or substantial

property damage if ignored.

Indicates special instructions on installation, operation or maintenance that are important but not

related to personal injury.

When Calling or Writing about the Boiler

Please have model and series from boiler rating label and CP number(s) from boiler jacket or controls.

Read all instructions before

installing. Failure to follow all

instructions in proper order can

cause severe personal injury, death

or substantial property damage.

Do not use petroleum-based

cleaning or sealing components in

boiler system. Severe damage to

system components can result,

causing substantial propety damage.

All manuals and user guides at all-guides.com

• Installation • Start-Up • Maintenance • Parts

Before Installing Boiler

Installation must comply with:

• State, provincial and local plumbing,

heating and electrical codes.

• Regulations of serving utilities.

• National codes where applicable.

Before selecting boiler location:

• Check for nearby connections to:

– fuel supply

– electrical power

– system water or steam piping

– venting systems - see page 23

– combustion and ventilation air supply - see

“Provide combustion and ventilation air

supply openings” below

• Check area around boiler for and remove any

combustible materials, gasoline and other

flammable vapors and liquids.

Failure to keep boiler area clear and free of

combustible materials, gasoline and other

flammable liquids and vapors can result in severe

personal injury, death and substantial property

damage.

Provide combustion and ventilation

air openings:

Do not install an exhaust fan in boiler room.

Adequate combustion and ventilation air must be

provided to assure proper combustion and

prevent possibility of flue gas leakage and carbon

monoxide emissions, causing severe personal

injury or death.

Opening sizes must comply with state, provincial

or local codes. In their absence, use the following

when boiler is in a confined room:

• Provide two permanent openings in boiler

room - one within 12 inches of ceiling, one

within 12 inches of floor. Minimum dimension

of each opening - 3 inches.

- When all air is taken from within building,

each opening should be at least one square

inch/1,000 Btuh boiler input and freely

connect with areas having adequate

infiltration from outside

- When all air is taken from outdoors, each

opening should connect directly or by ducts

from outdoors or crawl or attic spaces that

freely connect with outdoors and sized as

listed below:

- through outside wall or vertical ducts - at

least one square inch/ ,000 Btuh boiler

input

- through horizontal ducts - at least one

square inch/2,000 Btuh boiler input

- where ducts are used, they should be same

cross-sectional area as free area of

openings they are connected to

- compensate for louver, grille or screen

blockage when calculating free air

openings. Refer to their manufacturer’s

instructions for size. If unknown, use:

- wood louvers - 20-25% free air

- metal louvers or grilles - 60-75% free air

- screens - not less than 1/ inch mesh

Lock louvers in open position, or interlock

with equipment to prove open before

boiler operation.

Part No. 550-1 1-705 3

Figure 1 Combustion and Ventilation Air

Openings Boiler Room Below Grade

Figure 2 Combustion and Ventilation Air

Openings Boiler Room Partially or Completely

Above Grade

GRADE

Grating – Min.

12" above avg.

snowline Louver – Min.

12" above avg.

snowline

Note:

Duct size

equal to total

louver area

Areaway Louver

Boiler room

floor

Boiler room

floor

Note:

Size of areaway

and grating to be

equal to or

greater than total

louver area.

All manuals and user guides at all-guides.com

Weil-McLain 78 Boiler For Gas Light Oil Gas/Light Oil Fired Burners

Before Installing Boiler

Provide clearances for servicing

around boiler:

• Back, for breeching - 30 inches.

• Left side, for cleaning and tankless heater

removal - 3 inches

• Allow sufficient space on remaining sides

for cleaning, servicing and burner

installation. See burner literature for length.

• Clearance from vent pipe to combustible

materials:

- singlewall vent pipe - 18 inches

- doublewall vent pipe - refer to vent pipe

manufacturer’s recommendations for vent

pipe clearances

Lay a foundation, if needed:

Floor construction and condition must be

suitable for weight of boiler when filled with

water. See page 31 for boiler weight/water

weight.

A level concrete or brick foundation is

required when:

• A floor could possibly become flooded

• Non-level conditions exist

Part No. 550-1 1-705

Boiler Foundation Length Table

Boiler “L”Boiler “L”

Model Inches Model Inches

378 23 878 58

478 30 978 65

578 37 1078 72

678 44 1178 79

778 51 1278 86

2" Min.

“L”

30"

Figure 3 Boiler Foundation

All manuals and user guides at all-guides.com

• Installation • Start-Up • Maintenance • Parts

Set Packaged Boiler or Block Assembly in Place

For packaged boiler:

1. Remove top jacket panel. Set aside until after

boiler is piped.

2. Remove lag screws (2 in front, 2 in rear) from

shipping rails.

3. Remove boiler from skid. Cables are already

attached to block assembly. See Lifting Weight

Chart.

• Using crane - hook middle of each cable to

eye of crane.

• Using hoist - hook middle of each cable to

hoist. Raise boiler off skid. Use pipe rollers

under skid angles to roll boiler.

. Place boiler in final position. Center boiler on

foundation, if used.

5. Level boiler. Shim under skid angles, if

necessary.

6. Cut off cables.

Cables are not intended for long-term usage.

Cables may corrode inside boiler, weakening their

lifting strength. Failure to remove cables can

result in severe personal injury, death or

substantial property damage.

7. Proceed to “ a: Perform Hydrostatic Pressure

Test,” page 12.

For block assembly:

1. Remove lag screws (2 in front, 2 in rear) from

shipping rails.

2. Remove boiler from skid. Cables are already

attached to block assembly. See Lifting Weight

Chart.

• Using crane - attach free end of cables to eye

of crane.

• Using hoist - attach free end of cables to

hoist. Raise boiler off skid. Use pipe rollers

under steel skid angles to roll boiler.

3. Place boiler in final position. Center boiler on

foundation, if used.

. Level boiler. Shim under skid angles, if

necessary.

5. Cut off cables.

Cables are not intended for long-

term usage. Cables may corrode

inside boiler, weakening their

lifting strength. Failure to

remove cables can result in

severe personal injury, death or

substantial property damage.

6. Inspect block assembly for disjointed sections.

Check gas-tight seal of flue collector hood, flue

collar and cleanout plates.

Gas tight seal must be

maintained to prevent possible

flue gas leakage and carbon

monoxide emissions, resulting

in severe personal injury or

death.

a. Open damper in flue collar.

b. Check inside section assembly for any light

passing through unsealed areas.

c. Mark all unsealed areas.

d. At unsealed areas, check for damaged

gaskets, sealing rope not in place, loose bolts

or nuts, or missing holddown clips. Correct

all conditions and repeat step b. If unsealed

areas still exist, contact your Weil-McLain

distributor or sales office before continuing

installation.

7. Proceed to “ a: Perform Hydrostatic Pressure

Test,” page 12.

Part No. 550-1 1-705 5

Lifting Weight Chart

Packaged Assembled Packaged Assembled

Boiler Boiler Block Boiler Boiler Block

Model Lbs. Lbs. Model Lbs. Lbs.

378 1355 1150 878 2650 2325

478 1615 1385 978 2910 2560

578 1875 1620 1078 3165 2795

678 2130 1855 1178 3425 3030

778 2390 2090 1278 3680 3265

All manuals and user guides at all-guides.com

Weil-McLain 78 Boiler For Gas Light Oil Gas/Light Oil Fired Burners

Assemble Block

Sections are top heavy. Unbolted sections may

fall if not supported, resulting in severe

personal injury or death.

Install back refractory blanket:

1.Lay back section on floor with ports face up.

2 Apply water glass as an adhesive to blanket.

3.Press blanket against back target wall as

shown in Figure .

.Using knife, cut hole through blanket to

expose observation port opening.

Prepare back section:

1.Apply 1/8" continuous bead of sealing rope

adhesive in sealing rope grooves. See Figure

. Do not get any adhesive on machined port

surfaces.

2. Place 1/2" sealing rope in groove. Around

curves, grasp at 1" intervals and push

together. Do not stretch.

Do not pre-cut rope. Gas tight

seal must be maintained to

prevent possibility of flue gas

leakage and carbon monoxide

emissions, causing severe

personal injury or death.

3.Remove any grit from port machined

surfaces with clean rag.

Do not use petroleum-based

cleaning or sealing compounds

in boiler system. Severe

damage to system components

can result, causing substantial

property damage.

.Place 7-1/2" and 3-1/2" sealing rings in

appropriate port openings. See Figure . If

sealing ring slips out of groove, stretch ring

gently for several seconds, then reposition in

groove.

Part No. 550-1 1-705

Cut off rope

even with

edges

Sealing rope

Cut off rope

even with

edge

Cut off

rope

even

with

edge

7 1/2"

Sealing

ring

Sealing

rope

Cut out

observation

port opening

Back refractory

(apply waterglass

to entire back side)

3 1/2”Sealing ring

Figure 4

All manuals and user guides at all-guides.com

all-guides.com

All manuals and user guides at all-guides.com

Prepare remaining sections:

1. Follow “Prepare intermediate section” for

remaining intermediate and front sections:

a. Remove any grit from threads inside tapped

holes with clean rag.

Do not use petroleum-based cleaning or sealing

compounds in boiler system. Severe damage to

system components can result, causing

substantial property damage.

b. Install TI (Tankless Intermediate) and SI

(Supply Intermediate) sections (when used)

in order shown in “Section Arrangement

Table”.

c. Check each section for proper sealing rope

position before proceeding to next section.

Failure to position sealing rope properly can

cause boiler to not seal gas-tight. Gas-tight seal

prevents possible flue gas leakage and carbon

monoxide emissions, resulting in severe personal

injury or death.

d. Make sure bottom refractory blanket has

been installed per instructions on page 7.

Install burner mounting plate on front

section:

1. Install four 1/2" x -3/ " studs to secure burner

mounting plate to section:

a. Thread and lock together two nuts on

rounded end of stud. Thread flat end of stud

into one of four holes located around opening.

b. Remove nuts.

c. Repeat steps a and b for remaining studs.

2. Install burner mounting plate:

a. Apply 1/8" continuous bead of sealing rope

adhesive in groove around opening in section.

b. Position 1/2" sealing rope in groove. Overlap

ends at least one inch.

c. Install burner mounting plate. Use 1/2"

washers and nuts.

Install observation port assemblies

on front and back sections:

1. Install front observation port assembly:

a. Apply 1/8" continuous bead of sealing rope

adhesive in groove on observation port.

b. Position 3/8" sealing rope in groove.

Overlap ends at least one inch.

c. Secure assembly to section. Use 5/16-18 x

3/ " slotted head screws.

2. Repeat above steps for back observation port

assembly.

If using TI sections:

Install tankless heaters and gaskets or heater

cover plates and gaskets. Use 3/8" x 3/ " studs

and nuts.

Weil-McLain 78 Boiler For Gas Light Oil Gas/Light Oil Fired Burners

Assemble Block

Part No. 550-1 1-705

W=Water, S=Steam, F=Front, TI=Tankless

Intermediate, I=Intermediate, SI=Supply

Intermediate for steam boilers, B=Back. “I”

sections can be substituted for “TI” sections.

If you would like to pressure-test block

assembly now, proceed to page 12.

Section Arrangement Table

Maximum Section Arrangement

Boiler No. of (all heaters must be

Model Heaters on left side of boiler)

378 W&S 1 F-TI-B

478 W&S 1 F-TI-I-B

578 W&S 2 F-TI-I-TI-B

678 W&S 2 F-TI-I-TI-I-B

778 W&S 2 F-TI-I-TI-I-I-B

878 W&S 3 F-TI-I-TI-I-I-TI-B

978 W&S 3 F-TI-I-TI-I-TI-I-I-B

1078 W 3 F-TI-I-TI-I-I-TI-I-I-B

1078 S 3 F-TI-I-TI-SI-I-TI-I-I-B

1178 W 4 F-TI-I-TI-I-I-I-TI-I-TI-B

1178 S 4 F-TI-I-TI-I-SI-I-TI-I-TI-B

1278 W 4 F-TI-I-TI-I-I-I-I-TI-I-TI-B

1278 S 4 F-TI-I-TI-I-SI-I-I-TI-I-TI-B

All manuals and user guides at all-guides.com

Weil-McLain 78 Boiler For Gas Light Oil Gas/Light Oil Fired Burners

Assemble Block

Prepare flue collector hood

assembly:

Make sure gaskets are intact, not torn or

otherwise damaged. These conditions can

cause possible flue gas leakage and carbon

monoxide emissions, resulting in severe

personal injury or death.

1. Stand one collector hood module on end.

2. Wipe all flanged surfaces with clean rag.

3. Lay gasket on flange. Refer to Figure 8.

. Place end cap on gasket, aligning flanged

surfaces. Secure with six 5/16" x 5/8" flanged

bolts and flanged nuts. Tighten to 30 - 35 in.-

lbs.

5. For 878 - 1278:

a. Stand remaining hood module on end.

b. Wipe all flanged surfaces with clean rag.

c. Lay gasket on flange.

d. Carefully place open end of first module on

top of gasket, aligning flanged surfaces.

e. Secure with six 5/16" x 5/8" flanged bolts

and flanged nuts.

6. Attach flat-stitched sealing rope to hood

assembly. See Figure 9:

a. Lay hood on floor with flanged side up.

b. Wipe flanged surface with clean rag to

remove dirt and oil.

c. Apply double-faced tape to flanged surface.

d. Apply rope to tape beginning on one side of

open end of hood, leaving 1/ " extending

past edge. Around corners, bend rope, do not

cut. Do not stretch rope.

Do not pre-cut rope. Gas-tight

seal must be maintained to

prevent possible flue gas leakage

and carbon monoxide emissions,

resulting in severe personal

injury or death.

e. Continue around entire flange. At other open

end, leave 1/ " rope extending past edge of

flange. Cut off excess rope.

Double-faced tape serves only to

hold sealing rope in place during

installation. It will disintegrate

over time. If collector hood and

sealing rope is removed for any

reason, new tape and new gasket

must be applied.

Part No. 550-1 1-705

Flat-stitched

sealing rope

Bend rope do not

cut or stretch

Flue collector

hood modules

Extend rope 1/4"

past open ends

Double-faced

tape applied to

flange

Flue collector

hood end cap

Figure 9 Sealing Rope Application on Collector Hood Assembly

All manuals and user guides at all-guides.com

Autres manuels pour 78

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Weil-McLain Chaudière

Weil-McLain

Weil-McLain GOLD CGt SERIES Manuel utilisateur

Weil-McLain

Weil-McLain Eco Tec 2 Series Manuel utilisateur

Weil-McLain

Weil-McLain WM97+70 Manuel utilisateur

Weil-McLain

Weil-McLain 486 Series Manuel utilisateur

Weil-McLain

Weil-McLain ULTRA Ultra-105 Manuel du propriétaire

Weil-McLain

Weil-McLain UltraOil Manuel utilisateur

Weil-McLain

Weil-McLain Evergreen 220 Manuel utilisateur

Weil-McLain

Weil-McLain CGa 3 Series Manuel utilisateur

Weil-McLain

Weil-McLain SVF 725 Guide de l'utilisateur

Weil-McLain

Weil-McLain ULTRA Oil 3 Series Manuel utilisateur

Weil-McLain

Weil-McLain WGO 4 Series Manuel utilisateur

Weil-McLain

Weil-McLain Aqua Balance WMB-155 Manuel utilisateur

Weil-McLain

Weil-McLain EcoTec 80 Manuel utilisateur

Weil-McLain

Weil-McLain Ultra Oil Manuel utilisateur

Weil-McLain

Weil-McLain SB0203 Manuel de référence

Weil-McLain

Weil-McLain GV90+ Mode d’emploi

Weil-McLain

Weil-McLain Oil Boiler Manuel utilisateur

Weil-McLain

Weil-McLain 78 Manuel utilisateur

Weil-McLain

Weil-McLain -105 Manuel utilisateur

Weil-McLain

Weil-McLain ECO 70 Mode d’emploi

Weil-McLain

Weil-McLain SlimFit Mode d’emploi

Weil-McLain

Weil-McLain 550 MBH Mode d’emploi

Weil-McLain

Weil-McLain Ultra Series 3 Manuel utilisateur

Weil-McLain

Weil-McLain GOLD CGS 550-110-260/0508 Manuel utilisateur

Manuels Chaudière populaires d'autres marques

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Manuel utilisateur

Radijator

Radijator BIO max 23.1 Manuel utilisateur

Brunner

Brunner BSV 20 Manuel utilisateur

Buderus

Buderus Logamax GB062-24 KDE H V2 Manuel utilisateur

Potterton

Potterton 50e Fiche technique

UTICA BOILERS

UTICA BOILERS TriFire Manuel utilisateur

Joannes

Joannes LADY Series Manuel

ECR International

ECR International UB90-125 Manuel d'instructions

Froling

Froling FHG Turbo 3000 Manuel utilisateur

Froling

Froling P4 Pellet 8 - 105 Manuel utilisateur

U.S. Boiler Company

U.S. Boiler Company K2 Manuel utilisateur

Henrad

Henrad C95 FF Manuel utilisateur

NeOvo

NeOvo EcoNox EF 36 Manuel utilisateur

Potterton

Potterton PROMAX SL 12 Manuel utilisateur

Eco Hometec

Eco Hometec EC 25 COMPACT Manuel utilisateur

Viessmann

Viessmann VITODENS 200 Mode d’emploi

Baxi

Baxi Prime 1.24 Manuel utilisateur

REXNOVA

REXNOVA ISA 20 BITHERMAL Manuel utilisateur