WEG DeviceNet CFW500 Guide rapide

USB Communication Plug-in

Module

Módulo Plug-in de

Comunicación USB

Módulo Plug-in de

Comunicação USB

CFW500

Installation, Conﬁguration and Operation Guide

Guía de Instalación, Conﬁguración y Operación

Guia de Instalação, Conﬁguração e Operação

Motors | Automation | Energy | Transmission & Distribution | Coatings

Summary / Índice

English

EspañolPortuguês

SUMMARY

1 SAFETY INFORMATION...............................5

1.1 SAFETY WARNINGS ...................................5

1.2 PRELIMINARY RECOMMENDATIONS.......5

2 GENERAL INFORMATION...........................5

3 CONTENTS OF THE PACKAGE...................6

4 ACCESSORY INSTALLATION .....................6

5 SETTINGS......................................................9

APPENDIX A – FIGURES...............................29

ÍNDICE

1 INFORMACIONES DE SEGURIDAD .........13

1.1 AVISOS DE SEGURIDAD ...........................13

1.2 RECOMENDACIONES PRELIMINARES... 13

2 INFORMACIONES GENERALES...............13

3 CONTENIDO DEL EMBALAJE..................14

4 INSTALACIÓN DEL ACCESORIO..............14

5 CONFIGURACIONES..................................17

ANEXO A – FIGURAS.....................................29

ÍNDICE

1 INFORMAÇÕES DE SEGURANÇA............21

1.1 AVISOS DE SEGURANÇA ..........................21

1.2 RECOMENDAÇÕES PRELIMINARES.......21

2 INFORMAÇÕES GERAIS ...........................21

3 CONTEÚDO DA EMBALAGEM..................22

4 INSTALAÇÃO DO ACESSÓRIO .................22

5 CONFIGURAÇÕES......................................25

ANEXO A – FIGURAS.....................................29

USB Communication Plug-in Module

English

CFW500 | 5

1 SAFETY INFORMATION

1.1 SAFETY WARNINGS

NOTE!

This guide contains important information

for the correct understanding and

proper operation of the CFW500-CUSB

Communication Plug-in Module.

Only use the CFW500-CUSB

Communication Plug-in Module in

CFW500 WEG inverters.

We recommend reading the CFW500

user’s manual before installing or operating

this accessory.

1.2 PRELIMINARY RECOMMENDATIONS

ATTENTION!

Always disconnect the general power

supply before connecting or disconnecting

the accessories of the frequency inverter

CFW500.

Wait for at least 10 minutes to guarantee

complete de-energization of the inverter.

2 GENERAL INFORMATION

This guide shows how tho install, configure and operate

the CFW500-CUSB Communication Plug-in Module.

This plug-in allow to the CFW500 an interface with PC

by Universal Serial Bus (USB) trough of an embedded

standard USB/UART converter (VCP- Virtual Com

Port.). The CFW500-CUSB allows the PC serial

communications for inverter commands, references

and variables monitoring, as well as SoftPLc debugging

and programming. For further information about this

refer to the CFW500 "Modbus RTU user's manual' and

"SoftPLC manual" in the CD-ROM.

USB Communication Plug-in Module

English

6 | CFW500

3 CONTENTS OF THE PACKAGE

When receiving the product, check if this package contains:

Accessory in anti-static packaging.

Cable with Mini-B and A plugs.

Installation, configuration and operation guide.

4 ACCESSORY INSTALLATION

The accessory is easily installed or replaced. For correct

installation of the accessory execute the following steps:

Step 1: With the aid of the installation CD, install the

virtual serial port driver. For further details refer to the

installation manual available in the CD-ROM.

Step 2: With the inverter de-energized, remove the front

cover of the Inverter (figure A.1 (a)).

Step 3: Remove the accessory (connected plug-in

module) if any, as in figure A.1 (a).

Step 4: Fit and press the accessory to be installed as

indicated in figure A.1 (b) and then assemble the front

cover of the inverter.

Step 5: Connect the cable to the terminals of the

plug-in module (mini-B connector) and microcomputer

(USB type A).

Step 6: Energize the inverter and check in display if the

P0027 parameter indicates the number 5 (P0027 = 5).

If this information is not true or the display of the HMI

won’t turn on, check if the module used is actually the

CFW500-CUSB, if the DIP-switches S2.1 and S2.2 are

OFF and repeat steps 2-6.

USB Communication Plug-in Module

English

CFW500 | 7

Step 7: Connect the USB cable to the PC, open the

“Control Panel”, and looking for “Ports (COM & LPT)” in

the “Device Manager”.

Step 8: If you do not have VCP (Virtual COM Port) driver,

the “Device Manager” will display the warning below.

Usually, the Windows operating system install the driver

automatically. Try to disconnect and reconnect the USB

cable. If it is not work, you can get the driver from website

http://www.ftdichip.com/Drivers/VCP.htm or product

manual CD-ROM and install it manually.

USB Communication Plug-in Module

English

8 | CFW500

Step 9: Check de VCP (Virtual COM Port) number

allocated to the CFW500-CUSB and use it to configure

the PC application program serial interface.

Step 10: If necessary, you can change the VCP number.

Open “Port Properties” (right click), select “Port Settings”

and click the button “Advanced…”.

USB Communication Plug-in Module

English

CFW500 | 9

Step 11: Change the COM Port number.

5 SETTINGS

The control connections (analogical input / output, digital

inputs / outputs and RS485 interface) must be performed

as shown in figure 1.

RS485 - B

GND

AI1

+10 V

AO1 rpm

≥5 kΩ

RS485 - A

DO1-RL-NO

DO1-RL-C

+24 V

DI1

DI3

DI2

DI4

DO1-RL-NC

DO2-TR

+24 V

USB Communication Plug-in Module

English

10 | CFW500

Connector Description

Superior Terminal

1DI1 Digital input 1

3DI2 Digital input 2

5DI3 Digital input 3

7DI4 Digital input 4

9+24 V +24 Vdc Power suply

11 DO1-RL-NO Digital output 1

(NO contact of relay 1)

13 DO1-RL-C Digital output 1

(common point of relay 1)

Inferior Terminal

15 DO1-RL-NC Digital output 1

(NC contact of relay 1)

2AO1 Analogical output 1

4GND Reference 0 V

6AI1 Analogical input 1

8 +10 V Reference +10 Vdc for potentiometer

10 DO2-TR Digital output 2 (transistor)

12 RS485 - A RS485 (terminal A)

14 RS485 - B RS485 (terminal B)

16 GND Reference 0 V

Figure 1: Signals of control connector

The location of the DIP-switches for selecting the type

of analog input and output signal and termination of

the RS485 line can be better visualized in figure A.2.

To use the analog inputs and/ or outputs with signal in

current, switch S1 and related parameters must be set as

indicated in table 1. For further details about the control

connections see chapter 3 - Installation and Connection

of the CFW500 user's manual

Table 1: Settings of switches to select the type of analog

input and output of the CFW500-CUSB

Input /

Output Signal Setting of

Switch S1

Range of

Signal

Parameter

Settings

AI1

Voltage S1.1 = OFF 0...10 V P0233 = 0 or 2

Current S1.1 = ON

0...20 mA P0233 = 0 or 2

4...20 mA P0233 = 1 or 3

AO1

Voltage S1.2 = ON 0...10 V P0253 = 0 or 3

Current S1.2 = OFF

0...20 mA P0253 = 1 or 4

4...20 mA P0253 = 2 or 5

Autres manuels pour DeviceNet CFW500

Table des matières

Langues :

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur