Warren Controls 2800 Series Instructions d'utilisation

This document covers the installation, operation and maintenance

of the Series 2800 Precision Globe Control Valves presented in the

“Series 2800 Product Specification”, including the 2820 Two-Way

Single Seat Valve, the 2828 Two-Way Single Seat Low Flow Valve, the

2830 Three-Way Mixing Valve, and the 2832 Three-Way Diverting/

Mixing Valve. Warren Controls Series 2800 Precision Globe Control

Valves feature rugged bronze or stainless steel bodies with a variety

of trim materials and port sizes. The equal percentage and linear

plugs in the 2-way valves and linear plugs in the 3-way valves

provide excellent modulating control of a wide variety of fluids

for pressure, temperature, level, and flow applications from –20 to

500ºF (dependent on contruction). The Series 2800 is ideally suited

where value and long life are important objectives for applications

including but not limited to the Chemical, Food & Beverage, General

Service, Refining, District Energy, and ideal for Pharmaceutical

Industries.

The instructions given herein cover generally the operation and

maintenance of subject equipment. Should any questions arise

which may not be answered specifically by these instructions,

they should be referred to Warren Controls Inc. for further detailed

information and technical assistance. This manual cannot possibly

cover every situation connected with the operation, adjustment,

inspection, test, overhaul and maintenance of the equipment

furnished. Every effort is made to prepare the text of this manual

so that engineering and design data is transformed into the most

easily understood wording. Warren Controls Inc., in furnishing this

equipment and this manual, must presume that the operation and

maintenance personnel assigned thereto have sufficient technical

knowledge and experience to apply sound safety and operational

practices which may not be covered herein. In applications where

Warren Controls Inc. furnished equipment is to be integrated with a

process or other machinery, these instructions should be thoroughly

reviewed to determine the proper integration of the equipment into

the overall plant operational procedures. Warren Controls does not

assume responsibility for the selection, use, or maintenance of any

product. Responsibility for proper selection, use, and maintenance

of any Warren Controls product remains solely with the purchaser

and end-user.

PRODUCT OVERVIEW

GENERAL INFORMATION

2800 IOM

TABLE OF CONTENTS

Overview ................................................Cover

Valve Identification.................................. 2-3

Information Present on Valve............... 4-5

Body vs. Application....................................6

Dimensions & Weights................................ 7

Installation & Operation......................... 8-9

Maintenance ...............................................10

Packing Adjustment..................................10

Parts/Overhaul ............................................10

Parts Kits ................................................. 11-16

Drawings................................................. 17-30

Installation Instructions & Maintenance Document

Series 28OO

PRECISION GLOBE CONTROL VALVES

2800_IOM_RevBa_1219

22600 Emrick Blvd • Bethlehem, PA 18020 • USA • 800-922-0085 • www.warrencontrols.com 2800_IOM_RevBa_1219

Series 2800 Precision Globe Control Valves are available with a

variety of actuators and accessories. These actuators and accessories

have separate instructions. For complete control valve installation,

operation, and maintenance instructions see also the instructions

for the actuator and accessories in use.

VALVE IDENTIFICATION

To use these instructions it is necessary to identify the configuration

of the valve. Factory assembled control valves have a nameplate

mounted on the actuator. The valve’s part number (P/N) is present

on the plate. The part number represents the configuration of the

control valve. To identify the valve’s type, size, actuator, accessories,

and other characteristics decode the part number using configura-

tion table. If the information is incomplete, incorrect, or not pres-

ent contact the factory with the valve serial number listed on the

plate. (See Information Present on Control Valves section for location

of part number, serial number, and other important information on

valve.)

ACTUATORS AND ACCESSORIES

Valve

Type Size

Body Ma

terial

End

Connection Trim Style Trim Material Trim Cv

2-Way

Single Seat

2-Way

Lo-Flow

3-Way

Mixing

3-Way

Diverting

050

1/2 inch

075

3/4 inch

100

1 inch

125

1-1/4

inch

150

1-1/2

inch

200

2 inch

Bronze

CF8M

Screwed

SCH 40

Buttweld End

Full Port

1st Port

Reduction

2nd Port

Reduction

3rd Port

Reduction

4th Port

Reduction

NOTE:

Port reductions

only available on

Type 20/28/30.

Check factory for

availability.

Model

Packing Type

Teflon

Graphite

Vacuum Service

EPDM

Stainless Steel,

Type 20 Bodies

come standard w/

PEEK bearings. Used

for Temp. up to

500°F.

VALVE BODY

28N

Equal %

Linear

Mod Lin

Types 30/32,

Linear Only

Types 28

Mod Lin Only

316SS *

Bronze

Alloy 6

17-4 PH

Teflon

PEEK

NOTE:

* Type 28, 316SS

trim uses

harder

Nitronic

60 seat.

TEMPERATURE LIMITS

Valve

Type

Body

Material

& Code Trim Material & Code Packing Type & Code T MAX T MIN

20 2-Way

Single Seat

Bronze B316 S, Alloy 6 6, 17-4 PH H, Teflon T, PEEK PEPDM L350ºF -20ºF

Bronze B316 S, Alloy 6 6, 17-4 PH H, Teflon T, PEEK PTeflon T, Vacuum Service V400ºF 32ºF

Bronze B316 S, Alloy 6 6, 17-4 PH H, Teflon T, PEEK PGraphite G400ºF -20ºF

CF8M F316 S, Alloy 6 6, 17-4 PH H, Teflon T, PEEK PEPDM L350ºF -20ºF

CF8M F316 S, Alloy 6 6, 17-4 PH H, Teflon T, PEEK PTeflon T, Vacuum Service V450ºF 32ºF

CF8M FTeflon T, PEEK PGraphite G450ºF -20ºF

CF8M F316 S, 17-4 PH H, Alloy 6 6Graphite G500ºF -20ºF

28 2-Way

Low Flow

Bronze B316 S, Teflon T, PEEK PEPDM L350ºF -20ºF

Bronze B316 S, Teflon T, PEEK PTeflon T, Vacuum Service V400ºF 32ºF

Bronze B316 S, Teflon T, PEEK PGraphite G400ºF -20ºF

CF8M F316 S, Teflon T, PEEK PEPDM L350ºF -20ºF

CF8M F316 S, Teflon T, PEEK PTeflon T, Vacuum Service V450ºF 32ºF

CF8M FTeflon T, PEEK PGraphite G450ºF -20ºF

CF8M F316 SGraphite G500ºF -20ºF

30 3-Way

Mixing

Bronze B316 SEPDM L350ºF -20ºF

Bronze B316 STeflon T, Vacuum Service V400ºF 32ºF

Bronze B316 SGraphite G400ºF -20ºF

CF8M F316 SEPDM L350ºF -20ºF

CF8M F316 STeflon T, Vacuum Service V450ºF 32ºF

CF8M F316 SGraphite G500ºF -20ºF

32 3-Way

Diverting

Bronze BBronze BTeflon T, Vacuum Service V300ºF 32ºF

Bronze BBronze BGraphite G, EPDM L300ºF -20ºF

CF8M F316 SEPDM L350ºF -20ºF

CF8M F316 STeflon T, Vacuum Service V450ºF 32ºF

CF8M F316 SGraphite G500ºF -20ºF

Series 2800 2800_IOM_RevBa_1219

Actuator

Series Action Spring Range Handwheel Positioners, I/P’s & Limit Switches

Air Filter

Regulators

Special

Options

ASCO

Solenoids

None

Reverse

Stem

Fail

Down

Direct

Stem

Fail Up

None

DIAPHRAGMS:

DL49

(49 Sq.In.)

DL49XR

DL84

(84 Sq.In.)

DL84XR

(84 Ext.Rng.)

NOTE :

4X & 8X Only

in Xtra-High

Spring Range.

4X & 8X

verseActing for

2-Way Valves.

8X Directed

Acting for

3-Way Valves.

None

Low 4-10 PSI

49R ; 3-9 PSI

49D, 84R/D

Full 5-14 PSI

49R ; 4-13 PSI

49D; 3-15 PSI

84R/D

High 9-15

PSI 84;115

10-14 PSI 49R

8-12 PSI 49D

Xtra-High

DL49XR,

DL84XR

None

Reverse

Direct

NOTE :

Must match

action.

None

Type 300,

0-30 PSI,

5 micron

Filter

Type 300,

0-60 PSI

5 micron

Filter

Type 350SS,

0-100 PSI,

25 micron

Filter

ACCESSORIES

None

120 VAC

COILS

8320G184

3-Way Brass

8320G202

3-Way SS

EF8320G184

3-Way

EXP Br.

F8320G202

3-Way

EXP SS

Vdc

COILS

8320G184

3-Way

Brass

ACTUATOR

ACTUATOR/BODY COMPATIBILITY:

Warren Controls does not assume responsibility for the selection, use, or maintenance of any

product. Responsibility for proper selection, use, and maintenance of any Warren Controls

product remains solely with the purchaser and end-user.

None

Special

Opts or

Set-up

SS Tubing

SS Tagging

SS Tubing

and Tagging

Note: Standard

pneumatic tubing is

copper. SS tubing “T”

is optional.

SS tagging “G” (Two

lines, 24 characters/

line) is optional.

SS tubing and

tagging together “B”

is optional.

0000

None

PosItioners

2xP_

BLX Pneumatic

2xE_

BLX ElectroPneumatic

2xI_

BLX ElectroPneu. Intrn. Safe

2xX_

BLX ElectroPneu. Exp. Proof

2xF_

BLX ElectroPneu. Fail Freeze

76P_

Moore760 Pneumatic *

76E_

Moore760 Electro-Pneumatic

TOZO

ABB TZIDC 4-20mA.

THN_

ABB TZIDC 4-20mA w/HART

Intrn. Safe & Non-Incend

TPN_

ABB TZIDC PROFIBUS PA

Intrn. Safe & Non-Incend.

TFN_

ABB TZIDC FOUNDATION

Fieldbus Intrn. Safe & Non-

Incend.

THX_

ABB TZIDC 4-20mA w/HART

Exp. Proof

TPX_

ABB TZIDC PROFIBUS PA

Exp. Proof

TFX_

ABB TZIDC FOUNDATION

Fieldbus Exp. Proof

PROXIMITY SWITCHES:

PX11

Mark 1 Series - 2 ea. SPDT

PX12

Mark 1 Series - 2 ea. SPDT

w/2k Pot.

PX13

Mark 1 Series - 2 ea. SPDT

w/4-20 Feedback

PX14

Mark 1 Series - 4 ea. SPDT

PX15

Mark 1 Series - 6 ea. SPDT

I/P’s Use with Diaphragm Only

MAP1

Type 500X I/P, 3-9 PSI

MAP2

Type 500X I/P, 9-15 PSI

MAP3

Type 500X I/P, 3-15 PSI

MAP4

Type 500X I/P, 1-17 PSI

MAP5

Type 500X I/P, 6-30 PSI

MAP6

Type 550X I/P, 0-30 PSI

MAP9

Type 950X I/P, 3-15 EXP

No Additions

w/Mech. Limit Swtitch’s

w/4-20 Feedback

w/Switch’s & Feedback

Note: L, F & B not

available for Bxl or BxX

4th digit spec.

Full Range Signal,

3-15 PSI or 4-20mA

Low of Split Range,

3-9 PSI or 4-12m

High of Split Range,

9-15 PSI or 12-20mA

xdigit spec.

4th digit spec.

* Available with Split

Ranges, Select “S” in

Special Options

FAILURE MODES:

MODE VALVE TYPE ACTUATOR ACTION

Closed 20/28 Reverse

Open 20/28 Direct

Upper Closed* 30/32 Direct

Upper Open 30/32 Reverse

*Standard

DIAPHRAGMS BODY

49 49 Sq.In. (DL49) For 28N Bodies

4X (DL49XR) For 28N Bodies

84 84 Sq.In. (DL84) For 28N Bodies

8X (DL84XR) For 28N Bodies

Individual Options

0No Additions

Fw/4-20 Feedback Module (4-

20mA w/HART Models ONLY)

Kw/Digital Position Feedback

Module (4-20mA w/HART Models

ONLY)

Lw/ 24VDC/AC Micro-Switch’s

(Exp. Proof Models ONLY)

Pw/Proximity Switch’s NC

Option Combinations (For

4-20mA w/HART Models ONLY)

A = F &K

B = F &L (Exp. Proof Models

ONLY)

C = F &P

E = K &L (Exp. Proof Models

ONLY)

G = K &P

J = F &K &L (Exp. Proof

Models ONLY)

M = F &K &P

See Actuators, Positioners, &

Accessories. Section of Product

Specication for details.

42600 Emrick Blvd • Bethlehem, PA 18020 • USA • 800-922-0085 • www.warrencontrols.com 2800_IOM_RevBa_1219

There is a great deal of information present on each control valve

ranging in importance from the part number and serial number to

the color of the paint and casting numbers. This information is im-

portant for identifying the valve, installing it correctly, and obtaining

parts. Examples of the current factory nameplates and flow arrow

plates used on Series 2800 control valves are shown here. The ac-

companying table identifies the information present and where to

find it on the control valve. There may also be other casting numbers

and foundry marks present that do not provide useful information.

Customer specific tagging may also present. The plates used, and

information present, on Warren Controls other product lines or older

valves may be different, contact the factory for details.

ACTUATOR NAMEPLATES

VBA NAMEPLATES

2-WAY 1/2 THRU 1 INCH • 2800 S/S VBA

3-WAY MIXING 1/2 THRU 1 INCH • 2800 S/S VBA

INDUSTRIAL VBA

INFORMATION PRESENT ON CONTROL VALVES

DL84 DL49

Series 2800 2800_IOM_RevBa_1219

PART NUMBER & SERIAL NUMBER

Information Symbol(s) Location Notes

Part number

(Configuration)

P/N On actuator • On Actuator Nameplate attached to leg(s) of actuator.

Serial number S/N On actuator

and

valve body

• On Actuator Nameplate attached to leg(s) of actuator.

• Sales order Number only stamped on valve body end connection (2800).*

*Number stamped using approximately 1/8 inch tall characters

FLOW DIRECTION(S)

Information Symbol(s) Location Notes

Flow direction

through valve

On valve body • On 2800 S/S VBA Nameplate attached to mounting boss on valve body

between the end conections (2800 S/S valves ½ thru 1 inch except S/S 2832).

• Arrow cast on valve body between the end connections (2800 S/S 2-way 1-1/4 thru 2

inch).

Inlet location INLET On valve body • Stamped on valve body inlet end connection (2-way 2800 bronze valves ½ thru 2 inch &

S/S valves 1-1/4 thru 2 inch).

Port locations

for 3-way valves

Uupper port,

Llower port,

Ccommon

port

On valve body • U, L, & C stamped on valve body end connections (3-way 2800 bronze valves ½ thru 2

inch & 3-way 2800 S/S valves 1-1/4 thru 2 inch & 1 inch S/S 2832).

INPUT SIGNAL & SUPPLY

Information Symbol(s) Location Notes

Input signal SIG On actuator • On Actuator Nameplate attached to leg(s) of actuator.

Supply pressure SUP or

SUPPLY

On actuator • On Actuator Nameplate attached to leg(s) of actuator.

VALVE ATTRIBUTES

Information Symbol(s) Location Notes

Maximum

temperature rating

of valve body

TMAX or

Tmax

On actuator

and

valve body

• On Actuator Nameplate attached to leg(s) of actuator.

• On Industrial VBA Nameplate wired to valve body between the end connections on

side opposite flow arrow plate (2800 bronze valves ½ thru 2 inch & 2800 S/S valves 1-1/4

thru 2 inch, & 1 inch except S/S 2832).

• On 2800 S/S VBA Nameplate attached to mounting boss on valve body between the

end connections on side opposite flow arrow plate (2800 S/S valves ½ thru 1 inch except

1 inch S/S 2832).

Trim Cv

(Flow coefficient)

Cv On valve body • On Industrial VBA Nameplate wired to valve body between the end connections on

side opposite flow arrow plate (2800 bronze valves ½ thru 2 inch & 2800 S/S valves 1-1/4

thru 2 inch, & 1 inch S/S 2832).

• On 2800 S/S VBA Nameplate attached to valve body between the end connections on

side opposite flow arrow plate (2800 S/S valves ½ thru 1 inch except 1 inch S/S 2832).

Trim style

(Characteristic)

CHAR On valve body • On Industrial VBA Nameplate wired to valve body between the end connections on

side opposite flow arrow plate. (2800 bronze valves ½ thru 2 inch & 2800 S/S valves

1-1/4 thru 2, & 1 inch S/S 2832).

Trim material TRIM MATL On valve body • On Industrial VBA Nameplate wired to valve body between the end connections on

side opposite flow arrow plate. (2800 bronze valves ½ thru 2 inch & 2800 S/S valves

1-1/4 thru 2 inch, & 1 inch S/S 2832).

Valve size SIZE On valve body • On 2800 S/S VBA Nameplate attached to mounting boss on valve body between the

end connections on side opposite flow arrow plate (2800 S/S valves ½ thru 1 inch except

1 inch S/S 2832).

Valve body material On valve body • If CF8M is cast on the valve the valve body material is 316 stainless steel.

INFORMATION PRESENT ON CONTROL VALVE

62600 Emrick Blvd • Bethlehem, PA 18020 • USA • 800-922-0085 • www.warrencontrols.com 2800_IOM_RevBa_1219

BODY STYLE VERSUS APPLICATION

2828

2-Way Single Seat Low Flow

Unbalanced Valve

Low Flow Trim with ANSI Class IV and VI leakage rates.

Sizes: 1/2, 3/4, 1 inch

Body: ANSI B16.15 Bronze 250LB Threaded (NPT), 316

Stainless Steel 300LB Threaded (NPT), or 316 Stainless

Steel 300LB SCH 40 Buttweld (BWE) Stainless Steel

body valves contain Fluoraz 797 O-Ring upper and

lower body seals.*

Trim: Modified Linear, 316 Stainless Steel, TFE, or PEEK

Leakage Rates: ANSI Class IV (Stainless Steel Trim),

ANSI Class VI (TFE and PEEK Trim)

Packing: Long-Life Multi-Stack EPDM Lip Packing (-20 to 350°F)

Guided Low-Friction TFE V-Ring, Spring Loaded (+32

to 450°F), Adjustable Graphite Packing (-20 to 500°F)

Temperature: -20 to 400°F (Bronze 250LB Threaded Body)

-20 to 450°F (316 Stainless Steel 300LB Threaded or

Buttweld Body w/ TFE or PEEK Trim)

-20 to 500°F (316 Stainless Steel 300LB Threaded

Body or Buttweld Body w/ Stainless Steel Trim)

Rangeability: 40:1 for Cv 1.00 and 0.50.

20:1 for Cv 0.25

2820

2-Way Single Seat Unbalanced Valve

The most commonly applied solution with ANSI Class IV and VI leakage

rates.

Sizes: 1/2, 3/4, 1, 1-1/4, 1-1/2, 2 inch

Body: ANSI B16.15 Bronze 250LB Threaded (NPT), or 316

Stainless Steel 300LB Threaded (NPT), or 316 Stainless

Steel 300LB SCH 40 Buttweld (BWE) Stainless Steel

body valves contain Fluoraz 797 O-Ring upper and

lower body seals.*

Trim: EQ% or Linear, 316 Stainless Steel, Alloy 6, TFE, PEEK,

or 17-4 PH Hardened Stainless Steel

Leakage Rates: ANSI Class IV (Stainless Steel and Alloy 6 Trim), ANSI

Class VI (TFE and PEEK Trim)

Packing: Long-Life Multi-Stack EPDM Lip Packing (-20 to 350°F)

Guided Low-Friction TFE V-Ring, Spring Loaded (+32

to 450°F), Adjustable Graphite Packing (-20 to 500°F)

Temperature: -20 to 400°F (Bronze 250LB Threaded Body)

-20 to 450°F (316 Stainless Steel 300LB Threaded or

Buttweld Body w/ TFE or PEEK Trim)

-20 to 500°F (316 Stainless Steel 300LB Threaded or

Buttweld Body w/ Stainless Steel or Alloy 6 Trim)

Rangeability: 50:1

2830

3-Way Mixing Valve

This valve has two inlets and one outlet, and is the simplest solution

for mixing or bypass applications with an ANSI Class IV leakage rate. In

normal applications the inlet pressures are near equal and control is

possible from 5% to 95% of travel with inlet pressures up to 100 PSI.

Sizes: 1/2, 3/4, 1, 1-1/4, 1-1/2, 2 inch

Body: ANSI B16.15 Bronze 250LB Threaded (NPT), or 316

Stainless Steel 300LB Threaded (NPT), or 316 Stainless

Steel 300LB SCH 40 Buttweld (BWE) Stainless Steel body

valves contain Fluoraz 797 O-Ring upper and lower

body seals.*

Trim: Linear, 316 Stainless Steel

Packing: Long-Life Multi-Stack EPDM Lip Packing (-20 to 350°F)

Guided Low-Friction TFE V-Ring, Spring Loaded (+32 to

450°F), Adjustable Graphite Packing (-20 to 500°F)

Temperature: -20 to 400°F (Bronze 250LB Threaded)

-20 to 500°F (316 Stainless Steel 300LB Threaded or

Buttweld)

Rangeability: 50:1

2832

3-Way Diverting/Mixing Valve

Designed as a diverting valve with one inlet and two outlets with ANSI

Class III leakage rate. However, flow can be reversed for mixing if this port

configuration is desirable. The difference between the upper port and

lower port pressure must not exceed 50 PSID.

Sizes: 1, 1-1/2, 2 inch

Body: ANSI B16.15 Bronze 250LB Threaded (NPT), or 316

Stainless Steel 300LB Threaded (NPT), or 316 Stainless

Steel 300LB SCH 40 Buttweld (BWE) Stainless Steel body

valves contain Fluoraz 797 O-Ring upper and lower

body seals.*

Trim: Linear, Bronze (Bronze 250LB Threaded), or 316 Stainless

Steel (316 Stainless Steel 300LB Threaded or

Buttweld)

Packing: Long-Life Multi-Stack EPDM Lip Packing (-20 to 350°F)

Guided Low-Friction TFE V-Ring, Spring Loaded (+32 to

450°F), Adjustable Graphite Packing (-20 to 500°F)

O-Ring: EPR (Bronze 250LB Threaded), Fluoraz 797 (316

Stainless Steel 300LB Threaded or Buttweld)

Temperature: -20 to 300°F (Bronze 250LB Threaded)

-20 to 500°F (316 Stainless Steel 300LB Threaded or

Buttweld)

Rangeability: 50:1

Stem Down

The upper port opens

and the lower port closes

Upper PortLower Port

Common Port

Flow Flow

Stem Up

The upper port closes

and the lower port opens

Upper Port Lower Port

Common Port

Flow

Stem Down

The valve closes

Stem Up

The valve opens

Stem Down

The upper port opens

and the lower port closes

Upper PortCommon Port

Lower Port

Flow

Flow Flow

Stem Up

The upper port closes

and the lower port opens

Upper Port Common Port

Lower Port

Flow

Flow Flow

Stem Down

The valve closes

Stem Up

The valve opens

FlowFlow

Stem Down

The valve closes

Stem Up

The valve opens

Stem Down

The upper port opens

and the lower port closes

Upper PortLower Port

Common Port

Flow Flow

Stem Up

The upper port closes

and the lower port opens

Upper Port Lower Port

Common Port

Flow

Stem Down

The valve closes

Stem Up

The valve opens

Stem Down

The upper port opens

and the lower port closes

Upper PortCommon Port

Lower Port

Flow

Flow Flow

Stem Up

The upper port closes

and the lower port opens

Upper Port Common Port

Lower Port

Flow

Flow Flow

Stem Down

The valve closes

Stem Up

The valve opens

FlowFlow

Stem Down

The valve closes

Stem Up

The valve opens

Stem Down

The upper port opens

and the lower port closes

Upper PortLower Port

Common Port

Flow Flow

Stem Up

The upper port closes

and the lower port opens

Upper Port Lower Port

Common Port

Flow

Stem Down

The valve closes

Stem Up

The valve opens

Stem Down

The upper port opens

and the lower port closes

Upper PortCommon Port

Lower Port

Flow

Flow Flow

Stem Up

The upper port closes

and the lower port opens

Upper Port Common Port

Lower Port

Flow

Flow Flow

Stem Down

The valve closes

Stem Up

The valve opens

FlowFlow

Stem Down

The valve closes

Stem Up

The valve opens

Stem Down

The upper port opens

and the lower port closes

Upper PortLower Port

Common Port

Flow Flow

Stem Up

The upper port closes

and the lower port opens

Upper Port Lower Port

Common Port

Flow

Stem Down

The valve closes

Stem Up

The valve opens

Stem Down

The upper port opens

and the lower port closes

Upper PortCommon Port

Lower Port

Flow

Flow Flow

Stem Up

The upper port closes

and the lower port opens

Upper Port Common Port

Lower Port

Flow

Flow Flow

Stem Down

The valve closes

Stem Up

The valve opens

FlowFlow

Stem Down

The valve closes

Stem Up

The valve opens

2-WAY VALVES

(Control of Liquids, Gases, and Steam)

3-WAY VALVES

(Control of Liquids)

*NOTE: Fluoraz is NOT compatible with the following solvents: acetates, acetone,

benzene, carbon tetrachloride, ethers, Freons, ketons, lacquers, methyl ethyl ke-

tone, toluene.

Series 2800 2800_IOM_RevBa_1219

DIMENSIONS & WEIGHTS

1/2, 3/4, 1 1-1/4 & 1-1/2 2

A 250THD 4-7/8 5-3/4 6-1/2

300THD5 6-1/8 6-1/2

300BWE 15-3/8 16-7/817

B 250THD 2-3/4 3-1/4 3-5/8

300THD & BWE3 3-1/2 3-7/8

C 250THD 2-7/8 3-1/2 3-3/4

300THD & BWE 2-7/8 3-1/2 3-3/4

Dimension (IN)

2820

Weight (LB) 250THD 8-1/2 14-1/2 18-1/2

300THD8 15-1/219

300BWE 9-1/218 22-1/2

*Includes 1-3/8 inch for air fitting on direct acting diaphragm actuators

CF = Consult factory

Face to face dimensions conform to

Historical Warren Controls standard and

are NOT ANSI/ISA compatible.

Dimensions & Weights

2-Way or 3-Way

w/ DL49 or 49XR

2-Way or 3-Way

w/ DL84 or 84XR

Allow 4-7/8 inch clearance above actuator

for removal.

Actual shipping weights may vary.

Valve Size (IN)

1/2, 3/4, 11-1/4 & 1-1/22

A 250THD 4-7/85-3/4 6-1/2

300THD 56-1/8 6-1/2

300BWE 15-3/8 16-7/817

B 250THD 2-23/32 3-13/164

300THD 2-23/32 3-3/8 3-3/4

300 BWE8 8-3/49

C 250THD 2-7/83-1/2 3-3/4

300THD & BWE2-7/8 3-1/23-3/4

Dimension (IN)

2830

Weight (LB) 250THD 9 15-1/220

300THD 815 18-1/2

300BWE 10-1/2 19 23-1/2

Valve Size (IN)

11-1/2 2

A 250THD 4-7/85-3/4 6-1/2

300THD 56-1/8 6-1/2

300BWE 15-3/8 16-7/817

B 250THD 3-15/32 3-13/164

300THD 2-23/32 3-3/8 3-3/4

300 BWE8 8-3/49

C 250THD 2-7/83-1/2 3-3/4

300THD & BWE2-7/8 3-1/23-3/4

Dimension (IN)

2832

Weight (LB) 250THD 9 16-1/221

300THD 816 19-1/2

300BWE 10-1/2 20 24-1/2

Valve Size (IN)

1/2, 3/4, 1

A 250THD 4-7/8

300THD5

300BWE 15-3/8

B 250THD 2-3/4

300THD & BWE3

C 250THD 2-7/8

300THD & BWE 2-7/8

Dimension (IN)

2828

Weight (LB) 250THD 8-1/2

300THD8

300BWE 9-1/2

Valve Size (IN)

2600 Emrick Blvd., Bethlehem, PA 18020-8010 www.WarrenControls.com

Te l: 800-922-0085 or 610-317-0800 Fax: 610-317-2989

DL49 Direct 11 6-3/8 12-1/4 16 25 CF

DL49 49XR Reverse 11 6-3/811-1/4 13-3/425CF

DL84 Direct 13-7/88-1/8 16-3/424-1/8 48-1/2CF

DL84 84XR Reverse 13-7/8 8-1/85-3/4 24 48-1/2 CF

Actuator

H MAX (IN) WEIGHT (LB)

HTIWHTIW)ni(d)ni(D

ACTUATOR HANDWHEEL STD*HANDWHEEL STD HANDWHEEL

Top mounted

Handwheel

Valve shown with DL49 Actuator as typical.

For additional actuator information see Series 2800 Product Specification and

the Installation Operation and Maintenance Instructions for the actuator in use.

DIMENSION (IN)

2820

VALVE SIZE (IN)

1/2, 3/4,

1-1/4 &

1-1/2 2

250THD 4-7/8 5-3/4 6-1/2

300THD 5 6-1/8 6-1/2

300BWE 15-3/8 16-7/8 17

B250THD 2-3/4 3-1/4 3-5/8

300THD & BWE 3 3-1/2 3-7/8

C250THD 2-7/8 3-1/2 3-3/4

300THD & BWE 2-7/8 3-1/2 3-3/4

Weight (LB)

250THD 8-1/2 14-1/2 18-1/2

300THD 8 15-1/2 19

300BWE 9-1/2 18 22-1/2

DIMENSION (IN)

2830

VALVE SIZE (IN)

1/2, 3/4, 1 1-1/4 & 1-1/2 2

250THD 4-7/8 5-3/4 6-1/2

300THD 5 6-1/8 6-1/2

300BWE 15-3/8 16-7/8 17

250THD 2-23/32 3-13/16 4

300THD 2-23/32 3-3/8 3-3/4

300BWE 8 8-3/4 9

C250THD 2-7/8 3-1/2 3-3/4

300THD & BWE 2-7/8 3-1/2 3-3/4

Weight (LB)

250THD 9 15-1/2 20

300THD 8 15 18-1/2

300BWE 10-1/2 19 23-1/2

DIMENSION (IN)

2828

VALVE

SIZE (IN)

1/2, 3/4, 1

250THD 4-7/8

300THD 5

300BWE 15-3/8

B250THD 2-3/4

300THD & BWE 3

C250THD 2-7/8

300THD & BWE 2-7/8

Weight (LB)

250THD 8-1/2

300THD 8

300BWE 9-1/2

DIMENSION (IN)

2832

VALVE SIZE (IN)

1 1-1/2 2

250THD 4-7/8 5-3/4 6-1/2

300THD 5 6-1/8 6-1/2

300BWE 15-3/8 16-7/8 17

250THD 3-15/32 3-13/16 4

300THD 2-23/32 3-3/8 3-3/4

300BWE 8 8-3/4 9

C250THD 2-7/8 3-1/2 3-3/4

300THD & BWE 2-7/8 3-1/2 3-3/4

Weight (LB)

250THD 9 16-1/2 21

300THD 8 16 19-1/2

300BWE 10-1/2 20 24-1/2

Face to face dimensions conform to Historical

Warren Controls standard and are NOT ANSI/ISA

compatible.

Actual shipping weights may vary.

TRIM

MATERIALS

FLOWING

DIFFERENTIAL

PRESSURE

LIMIT

Bronze 50 PSID

316 Stainless Steel 100 PSID

TFE 100 PSID

PEEK 100 PSID

17-4 pH

Hardened Steel 200 PSID

Alloy 6 300 PSID

Pressure reatings are PSIG

For applications below 32° consult factory.

For applications above 375°, 300THD Stainless

Steel Body is recommended.

BODY PRESSURE-

TEMPERATURE RATINGS:

Temperature

(F)

250 THD

Bronze

300

THD&

BWE SS

+32° To 100°F 400 720

150° 400 670

175° 392 645

200° 385 620

225° 375 605

250° 365 590

275° 350 575

300° 335 560

325° 317 548

350° 300 537

375° 275 526

400° 250 515

450° - 497

500° - 480

82600 Emrick Blvd • Bethlehem, PA 18020 • USA • 800-922-0085 • www.warrencontrols.com 2800_IOM_RevBa_1219

See also separate actuator and accessory instructions for addi-

tional installation guidelines.

• Be sure that the flow medium, ambient temperature and the selected loca-

tion will not exceed the maximum temperature of the valve, actuator, or ac-

cessories. Information can be found in the product specifications and on the

nameplate(s) regarding these limits (See Information Present on Control Valves

section for location of important information on valve).

• Follow good piping practices. Install a bypass around the valve. Install stop

valves in inlet and outlet piping to provide means to isolate valve.

• A straight run of pipe is recommended for 10 pipe diameters upstream of the

valve and 20 pipe diameters downstream of the valve.

• Protect valve and downstream equipment with a self-cleaning strainer.

• Provide proper inlet and outlet drainage in steam service to prevent water

hammer or possible erosion in equipment.

• Install gauges in inlet and outlet piping to provide means for checking adjust-

ment and operation.

• For maximum efficiency and minimum wear install valve in vertical position

with the stem pointing upward.

• Actuators mounted in any position other than vertical must be supported inde-

pendent of the valve.

• Be sure to leave clearance to allow for actuator removal (See Dimensions &

Weights section of Product Specification for actuator removal clearance).

• Before installing, be sure valve and piping are clean inside and free of scale,

chips, welding spatter, and foreign material. Thoroughly blow out or flush pipe

lines.

• The valve must be installed with the fluid flowing in the correct direction(s). For

proper operation in all applications, control valves must be piped according to

the corresponding flow arrows, inlet markings, and port markings present on

each valve (See Information Present on Control Valves section for location of

important information on valve).

• Pipes must be aligned squarely with the valve at each connection.

• If the valve has screwed ends, do not apply pipe dope to the threads of the

valve body or to the first two threads of the pipe.

• If the valve has flanged ends, tighten flange bolts evenly to prevent excessive

stress and the possibility of cracking.

• If the valve has welded ends, prevent plug and cage distortion by keeping ex-

cess heat from the body.

Check valve for any

damage due to improper

storage or transportation.

Immediately notify your

sales organization of any

damaged goods upon

receipt. Do not attempt to

move or disturb the valve

further so photos may

be taken. If the shipping

container is noticeably

damaged refuse receipt,

as the shipping company

should be held liable until

a shipping representative

is available to take photos.

INSTALLATION

Series 2800 2800_IOM_RevBa_1219

• The valve, actuator, and accessories (if so equipped) are assembled, tested, and

calibrated at the factory. The actuator nameplate specifies set-up parameters

used (See Information Present on Control Valves section for location of impor-

tant information on valve). Do not exceed the supply pressure listed on the

actuator nameplate or you will damage the valve and void the warranty.

• Supply air or voltage, instrument signal, and accessories should be connected

to ports or terminals as indicated on the control valve.

• Final tuning may be required under actual operating conditions.

• On critical or dangerous equipment, provide suitable safety and emergency

systems to protect personnel and property from injury due to a valve malfunc-

tion. If the valve handles flammable, toxic, corrosive or explosive fluids, pro-

vide for safety in the event of valve leakage or malfunction.

• Do not obscure flow arrow plates or nameplates with paint. If flow arrow plates

or nameplates will be covered with insulation, it is recommended the informa-

tion on the plates be transcribed on the outside of the insulation in the same

location as the plate.

OPERATION

• Close inlet and outlet stop

valves.

• Check that valve responds

through rated travel in re-

lation to changes in input

signal. Rated travel is shown

by position of travel indica-

tor on valve stem relative to

travel indicator on yoke.

• For valves fitted with a

handwheel, manually oper-

ate valve using handwheel

through rated travel to

check freedom of move-

ment. Return handwheeel to

its standby position.

• Place valve in operation.

INSTALLATION CONT.

10 2600 Emrick Blvd • Bethlehem, PA 18020 • USA • 800-922-0085 • www.warrencontrols.com 2800_IOM_RevBa_1219

Series 2800 Precision Globe Control Valves are for the most part

maintenance free when properly selected and installed. Rebuild-

ing of these valves should not be necessary under normal operat-

ing conditions. For best operation follow installation guidelines (See

Installation section); maintain the fluid pressure, temperature, flow,

flowing differential pressure, and shut-off differential pressure within

the limits of the valve (See Series 2800 Product Specification for de-

tails). In installations where high vibration exists, pneumatic and/or

electrical connections should periodically be checked for integrity. In

water or water and glycol applications, good water quality must be

maintained or the service life of the valve may be reduced (See Water

Quality Guidelines). The valve stem must be kept free of debris, de-

posits, dirt, dust, and scratches or the packing parts may be damaged

resulting in a packing leak. Control valve hunting will cause excessive

stroking of the valve stem and result in premature failure of the pack-

ing seal. The system must be stabilized to prevent hunting to ensure

reasonable packing life and optimal control performance. Oversizing

of a control valve will result in an unstable condition, which can cause

noise, vibration, and premature trim and packing seal failure. The use

of Warren Controls ValveWorks sizing program will facilitate the selec-

tion of the optimum valve.

MAINTENANCE

PACKING ADJUSTMENT

PARTS/OVERHAUL

Series 2800 Precision Globe Control Valves have either self-adjust-

ing packing or adjustable packing. Valves with Body Material BBronze

and Packing Type TV-ring, VVacuum Service, or LLip Packing have

self-adjusting packing and require no external adjustment. If the valve

has self-adjusting packing and a packing leak is observed replace the

packing and if necessary the stem and plug assembly.

Valves with Body Material BBronze and Packing Type GGraphite have

adjustable packing. Valves with Body Material SCF8M and Packing

Type TV-ring, GGraphite, or VVacuum Service Packing also have ad-

justable packing. If the valve has adjustable packing and a packing

leak is observed, tighten the packing nut ¼ turn and observe. If the

leak continues tighten the packing nut another ¼ turn and observe.

Repeat as necessary. If the leak continues and the packing nut cannot

be tightened further with reasonable force replace the packing and if

necessary the stem and plug assembly.

Damaged or worn parts can decrease performance and shorten valve

life.

Damaged or worn packing parts including the packing, bearings,

spring, and other bonnet parts can cause a packing leak resulting in

damage to the actuator, accessories, and surrounding equipment.

Damaged or worn packing parts can also cause increased hysteresis

resulting in poor control.

Damaged or worn trim parts including the plug, stem, seat ring, pis-

ton, and o-ring can cause increased hysteresis, poor control, excessive

internal leakage, and poor shut-off. Damaged or worn trim parts can

also cause damage to the packing parts resulting in a packing leak.

Damaged or worn body gaskets or o-ring seals can cause external

leakage resulting in damage to the actuator, accessories, and sur-

rounding equipment.

Should parts become worn or damaged, parts kits are available. Re-

pack Kits are available to replace the packing. Repack/Inspection

Kits are available to allow the valve to be opened for inspection of

its internal parts. Rebuild/Repack Kits are available to completely re-

build/ overhaul the valve. Parts kits come with complete step-by-step

instructions. Each kit has its own part number. Please provide the

valve’s serial number to ensure getting the correct kit part number

and correct parts.

DO NOTDO NOT ATTEMPT

TO SERVICE A

SERIES 2800

VALVE WITHOUT

HAVING A

REPACK/

INSPECTION KIT &

SUPPLEMENTAL

INSTRUCTIONS

ON HAND.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Warren Controls Unité de contrôle

Warren Controls

Warren Controls 377 Mode d’emploi

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur