VOGELS PFW 6854 Manuel utilisateur
Display Wall Mount, Rotating
MOUIN_PFW6854_V02
Max: 72kg/160lbs
PFW 6854
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione,
Guide d’Installation, Installatie gids
Page 2 Installation Instructions
Table of Contents
PFW 6854
Parts List 2
Installation Tools 3
Thread Depth Indicator 6
Mount Installation 7
Concrete Mounting 8
Universal Mounting Bracket Installation 8
Display Orientation 10
Technical Specications 10
Lock-it Security Manual 11
Parts List
This mount is shipped with all installation hardware and components. Make sure that none of these parts are
missing and/or damaged before beginning installation.
Griplate™ (Qty 8)
5/16” x 3” Lag Bolts - wooden studs
only (Qty 6)
5/16” Flat Washers
(Qty 4)
Universal Mounting Brackets (Qty 2) Rotating Universal Bracket Bar (Qty 1)
M6 Knurl Knob
(Qty 1)
PFW 6854 Mounting Bracket (Qty 1)
Finned Anchors M10 x 60
(Qty 6)
Installation Instructions Page 3
Installation Tools
Phillips Head Screw Driver Soft Material/Blanket 1/2” Socket and Wrench
Pencil Tape Measure Drill Gun
Level (Supplied) M5 Allen Wrench (Supplied) 5/32” Allen Wrench (Supplied)
1/4” Drill Bit (Pilot Holes) Thread Depth Indicator (Supplied)
Masonry Drill Bit (Concrete Applications - Commercially Available)
PFW 6854
Qty 8
Qty 8
Qty 8
Qty 8
Qty 8
Qty 8
Qty 8
Qty 8
Qty 4
M6 x 45
M8 x 20
M8 x 25
M8 x 30
M8 x 35
M8 x 45
M8 x 70
M4 x 16
M4 x 25
M5 x 12
M5 x 16
M5 x 20
M5 x 25
M5 x 50
M6 x 16
Qty 8
Qty 8
Qty 8
Qty 8
Qty 8
Qty 8
Qty 8
Qty 7
M6 x 20
M6 x 30
Page 4 Installation Instructions
PFW 6854
The nylon spacers may be stacked to achieve proper spacing.
5/16" Flat washers
(metal)
1/4" Nylon spacers
(Qty 8)
(small)
(Qty 8)
1/2" Nylon spacers
1/4" Nylon spacers
(Qty 12)
(large)
(Qty 8)
(large)
(Qty 8)
Nylon sleeves
9/16" Nylon spacers
(Qty 8)
1" Nylon Spacers
(Qty 8)
Installation Instructions Page 5
PFW 6854
Thread Depth Indicator
1. Insert the thread depth indicator (supplied) through the thread inserts found on the back of the at panel to make sure the inserts
measure the same full depth and mark it (Figure 1).
2. Locate the correct diameter screw for the thread insert. Compare your marking to the screws (supplied).
3. If your selected screw is longer than the marking on the thread depth indicator, DO NOT USE this screw.
4. The screw length must not bypass the marking. Select another screw size (Figure 2 and 3), until you nd one that comes closest to
your mark without going past.
Thread Depth
Indicator
Marking
Screw
Marking
Screw
Thread Depth
Indicator
Inverted Flat
Panel Display
Marking the
Depth
Thread Insert
Thread Depth
Indicator
Figure 1
Figure 2 Figure 3
Page 6 Installation Instructions
PFW 6854
Mount Installation
Determine where the mount lo-
cation will be. Use a stud nder
to locate the nearest wall stud.
Once the stud has been located, use a
pencil to mark the spot.
Using a 1/4” drill bit, drill the upper mount-
ing hole where the mark was made.
Step 1 Step 2 Step 3
For ease of installation, it is recommended that two people perform the installation. One person should hold
the mount while the other person installs the lag bolt and washer. Making sure that the mount is level, the
person not holding the mount must mark and drill the second mounting hole and secure the second lag bolt
and washer.
Place a level (supplied) on the top
rail and make sure that the mount is
level. Once the mount is level, Drill
pilot holes in the lower mount-
ing slots and install two (2) 5/16” x
3” lag bolts and washers into the
mounting holes and tighten.
Step 6
Step 5
Step 4
Insert two (2) 5/16” x 3” lag bolts
and washers into the mounting
holes and tighten (see WARNING:
below
After the holes have been pre-drilled,
line up the mounting slot openings
with the pre-drilled holes.
If the studs are 12” (304.8mm) apart, use three (3) 3” (76.2mm) lag bolts for the top rail and three (3) 3” (76.2mm)
lag bolts for the lower rail. If the studs are 16”(406.4mm), 18” (457.2mm) or 24” (609.6mm) apart, use two (2) 3” lag
bolts for the top rail and two (2) 3” lag bolts for the lower rail.
Do NOT over-tighten lag bolts when attaching the mount to the wall. Improper installation may result in personal
injury or damage to property.
Installation Instructions Page 7
PFW 6854
Concrete Mounting
Concrete anchors must be used for concrete installation. They can be purchased at your local hardware store. The
mounting surface must be a minimum 6” thick.
For the two upper mounting points, the Griplate™ at side must be facing up. For the two lower mounting points,
the Griplate™ at side must be facing down.
IT WILL TAKE TWO PEOPLE TO COMPLETE THE NEXT INSTALLATION STEP.
1. Begin by placing the mount into position against the wall, keeping it level.
2. Mark off four holes to be used for securing the mount.
3. Next, drill holes using a masonry bit for your anchors (recommended masonry bit).
4. Insert a commercially available concrete anchor into each hole (recommended 3/8” anchors).
5. If necessary, a hammer can be used to lightly tap each anchor into place so that they are ush with the wall.
6. Once all of the anchors are in place, move the wall bracket into position.
7. Attach the nut onto the threaded shaft that is protruding from the wall.
8. Do not tighten until all nuts are in place.
5. At this time, center the universal bracket bar and tighten the set screws that are located on the universal brackets.
Universal Mounting Bracket Assembly
1. Place the universal bracket bar and the universal brackets on a at surface.
2. Slide the universal brackets onto the universal bracket bar (as shown below) with the set screws facing up. At this
time, do not tighten the set screws that are located on the universal bracket.
3. Place the display on a soft, at surface, face-down. Next, place the universal bracket assembly on the back of the
display, with the universal brackets resting directly over the display mounting points.
4. Once the desired position has been determined, place the Griplate™ washers over each mounting point and secure
them using the appropriate hardware (see Page 5).
Universal Mounting Brackets
Set Screw
Griplate™ Universal Bracket Bar Griplate™
DIM PLES
FACING UP
D IM PLES
FACING DOW N
D IM P L E S
FACING UP
D IM PLES
FACING DO W N
M4
M8
M6
M5
Page 8 Installation Instructions
PFW 6854
After loosening the tension bolts, be sure that
the nose piece is held together tightly before
rotating.
6. Lower the universal bracket bar with attached
display into the cradle (as shown to the left).
Nylon
Sleeve
Knurl Knob Mounting Point/M6 x 12mm Security Head and
M6 Lock Washer Mounting Point.
7. Insert an M6 Knurl Knob/M6 x 12mm Security
Head and M6 Lock Washer into the knurl knob/
security screw mounting point and tighten.
To access the knurl knob/security screw
location while the display is attached, the
PFW 6854 must be rotated to the “portrait”
position (vertical position
8. Tighten the two (2) Phillips head screws (located
on the side of the mounting block) once the nal
position is attained.
Locking Screws
Installation Instructions Page 9
PFW 6854
Display Orientation
The PFW 6854 will allow the user to adjust the display a full 360°.
BEFOREROTATINGTHEPFW6854,MAKESURETHATTHEM6KNURLKNOBISSECURELYFASTENEDTOTHE
PFW6854.ALSO,PLEASEMAKESUREYOUALLOWENOUGHCABLEANDWIRECLEARANCEFORFULLROTATION.
1. To adjust the PFW 6854, rotate the display
either clockwise or counter-clockwise.
M6 Knurl Knob
2. Tighten the two Phillips head locking
screws (see Step 8, Page 10)
Technical Specications
All measurements are in inches (mm).
Page 10 Installation Instructions
PFW 6854
Lock-It™ Security Hardware Pack
The PFW 6854 is shipped with a safety knurl knob already installed. If the user decides to incorporate the optional security hardware,
the following steps will show the user how to effectively remove the safety knurl knob and install the optional Lock-It™ hardware
kit.
NOTE: The M6 security head screw will be installed after the PFW 6854 has been fully assembled. Installation
of the M6 security head screw prior to completing assembly will not allow the PFW 6854 to function properly.
M6 x 12mm
Security Head
Screw (Qty 1) and
Lock Washers
(Qty 2)
Security Allen
Wrench
(Qty 1)
Step 1
Remove the PFW 6854 from the packaging and
remove the existing safety knurl knob. Remove the
universal bracket bar.
Step 2
Place the two lock washers onto the M6x12mm security head
screw. Place the M6x12mm security head screw onto the
security allen wrench and insert into mounting point.
Step 3
Once inserted into the mounting point, fully tighten
into place using the security Allen wrench.
Step 4
Once the M6 security head screw has been installed, re-insert
the safety knurl knob. Installation completed. This will prevent
the display from being removed from the assembly.
Allen
Wrench
Safety Knurl
Knob
M6 Security Head Screw
and Lock Washers
Universal
Bracket Bar
Safety Knurl
Knob
M6 Security Head Screw
and Lock Washers
Table des matières
Autres manuels VOGELS Support et étagère
VOGELS
VOGELS EMC 5000 - MOUNTING Manuel utilisateur
VOGELS
VOGELS SOUND 3450 Manuel utilisateur
VOGELS
VOGELS THIN RC 355 Manuel utilisateur
VOGELS
VOGELS EFW 8305 Manuel utilisateur
VOGELS
VOGELS SFS 4113 Series Manuel utilisateur
VOGELS
VOGELS TriMotor VFWE 552 RC Manuel utilisateur
VOGELS
VOGELS EFW 8345 Manuel utilisateur
VOGELS
VOGELS EFA 8825 Manuel utilisateur
VOGELS
VOGELS PFA 9134 Manuel utilisateur
VOGELS
VOGELS THIN 525 Manuel utilisateur
VOGELS
VOGELS W52070 Manuel utilisateur
VOGELS
VOGELS VFW 226 - VFW 326 VFW 426 Manuel utilisateur
VOGELS
VOGELS EPA 6505 Manuel utilisateur
VOGELS
VOGELS WALL 2250 Manuel utilisateur
VOGELS
VOGELS PFF7810 Manuel utilisateur
VOGELS
VOGELS SFS 4133 Series Manuel utilisateur
VOGELS
VOGELS PLW 1001 Manuel utilisateur
VOGELS
VOGELS THIN 445 Manuel utilisateur
VOGELS
VOGELS TVB 2375 Manuel utilisateur
VOGELS
VOGELS COMPOSE CFAE 140 RC Guide de référence
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
