VMP LCD-CM2 Manuel utilisateur

Ce manuel convient aux modèles suivants

1

Table des matières

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur

For more information, please contact us at:

325 Log Canoe Circle, Stevensville, Maryland 21666

(T) 410.643.6390 / (F) 410.643.6615

www.videomount.com

VIDEO MOUNT PRODUCTS

Instruction Sheet For:

LCD-CM2

Step1

Before starting, lay out all parts to your mount and match them to the

partslistprovided. Verifythatyouhaveallyourpartsbeforeattempting

to assemble the mount. Note: The LCD-CM2 and LCD-1C combo was

designed to mount two of the same TV or TVs of similar size and weight.

It is not designed to have two signiﬁcantly different TVs mounted. Also

note that LCD-1C part numbers have circles around their numbers and

LCD-CM2 has hexagons around their part numbers.

Step 2

For the follow steps it is assumed that you are assembling a new

LCD-1C and LCD-CM2. If you are retro ﬁtting a LCD-1C then pro-

ceed to step 8. Mark the ceiling or desired mounting surface in

preparation of installation of the ceiling plate LCD-1C. Pre-

drill if necessary and mount the ceiling plate LCD-1C to the

desired surface.

Warning: Please verify that your mounting surface

will support the combined weight of your mount, mounting hard-

ware, and monitor. Also verify that the mounting surface is safe to

drill through. If in doubt, please contact a profession installer.

Step 3

Determine which VESA standard plate you will be using. If your TV

follows the VESA 75 standard then you should use the small mount-

ing plate LCD-1C / LCD-CM2. If your TV follows the VESA 100

standard then you should use the big mounting plate LCD-1C /

LCD-CM2. Once you determined the correct VESA plate attach

it to the pivot bracket LCD-1C / LCD-CM2 using the M6 screw

LCD-1C / LCD-CM2 and nylon nut LCD-1C / LCD-CM2.

Step 4

Attachthe pivotbrackets assembliesfrom step3 tothe supporttube

LCD-CM2 using the 3/8” screw LCD-1C / LCD-CM2,

washers LCD-1C and LCD-CM2, and nylon nut LCD-1C /

LCD-CM2. Insert the adjusting screw LCD-1C / LCD-CM2

into the back of the pivot bracket LCD-1C / LCD-CM2.

Step 2: Mounting the ceiling plate

Step 3: Attaching the mount plate

to the pivot bracket

Step 4: Attaching the pivot

bracket to the support tube

VIDEO MOUNT PRODUCTS

6

Key:

LCD-1C

LCD-CM2

1

1

4

5

3

42

9775

116 11

15 8

6

42

10

12 8

Step 5

Attach the extend tube LCD-1C to the support tube LCD-

CM2 using the M12 bolt LCD-1C and washers LCD-1C.

Secure the M12 bolt LCD-1C in the extend tube LCD-1C by

screwing in the ¼” brake screw LCD-1C.

Step 6

Attach your TV to the VESA standard plate you choose earlier us-

ing either the M4 LCD-1C / LCD-CM2 or M5 LCD-1C

/ LCD-CM2 screws as appropriate.

Step 7

Attach the extend tube LCD-1C to the ceiling plate LCD-1C

using the 5/16” screw LCD-1C and nylon nut LCD-1C. Pro-

ceed to step 10.

Step 8

Remove the extend tube LCD-1C from the ceiling plate

LCD-1C by removing the 5/16” screw LCD-1C and nylon nut

LCD-1C.

Step 9

Remove the support tube LCD-1C from the extend tube

LCD-1C by removing the ¼” brake screw LCD-1C and

then removing the M12 bolt LCD-1C and washers LCD-1C.

Remove the adjusting screw LCD-1C from the pivot bracket

LCD-1C. Removethepivotbracket LCD-1Cfromthesupport

tube LCD-1C by removing the 3/8” screw LCD-1C, washers

LCD-1C and nylon nut LCD-1C. Remove the end plugs

LCD-1C from the support tube LCD-1C. Proceed to step 3.

Step 5: Attaching the support

tube to the extension tube

Step 6: Attaching the TVs to the

mount plate

Step 7 : Attaching the extend

tube to the ceiling plate

10

2

13

1

11

10 2

17

22

12

21

19

2

18

1

2

118

19

3

172

10 11

12

44

3 16

15 8

14 3

Step 8 : Removing the extend

tube from the ceiling plate Step 9 : Removing the

support tube

WARNING: The installer of these products must verify that the mount-

ing surface, ceiling or wall, will safely support the combined weight

of all attached equipment and hardware. Video Mount roducts will

not be held liable for the improper use or installation of its products.

Enjoy Your Mount!

Step10

Insert the end plugs LCD-1C into the support tube LCD-CM2.

For cable management, insert the cable clips LCD-1C / LCD-

CM2 into the support tube LCD-CM2. Please verify that all nuts

and screws are tight.

Step 10: Inserting end plugs

and cable clips

VIDEO MOUNT PRODUCTS

Key:

LCD-1C

LCD-CM2

14 1

13 9

1