VMP ER-1-4PKIT Manuel utilisateur

ER-1-4PKIT

Instruction Sheet For:

For more information, please contact us at:

345 Log Canoe Circle, Stevensville, Maryland 21666

Toll Free: 877.281.2169 Phone: 410.643.6390 Fax: 410.643.6615

www.videomount.com

7

4A

10

8

2A

2B

11

ER-1-4PKIT

ITEM NO.

DESCRIPTION

QTY.

2A

Left Support "L"

1

2B

Right Support "L"

1

4A

Support Plate A

1

7

Cross Screw 1/4"-20UNC*L1/2"

22

8

Hex Nut 1/4"-20UNC

18

10

Connector Plate

2

11

Middle Connector Plate

2

Step 1

Before starting lay out all parts to your mount and match them to

the parts list provided. Verify that you have all your parts before

attempting to assemble the mount. Also before attempting to as-

semble the ER-1-4PKIT you should have already assembled the ER-1.

Note: ER-1-4PKIT part numbers are in circles and ER-1 part numbers

are in triangles.

Step 2

Attach the middle connector plates to the left and right “L”

supports and using the ¼”- 20 screws and nuts .

Step 3

Attach the connector plates to the support plate A using

the ¼” – 20UNC screws and nuts .

Step 4

Attach the connector plates to the back of the support plate B

using the ¼” – 20UNC screws and nuts that were originally

used in the ER-1 to bind the support plate B to the rear of the

left and right support.

Step 5

Attach the left support “L” to the ER-1 by rst attaching the

left support “L” to the side of the support plate A using ¼”

– 20UNC screws . Then connect the middle connector plate

to the left support using ¼” – 20UNC screws and nuts

. Attach the left support “L” to the base using ¼” –

20UNC screws and nuts making sure to attach the rail to

both the side and the back of the base using all three attach-

ment points. Repeat this for the right support “L” .

Please verify that all nuts and screws are securely tightened.

Step 2: the middle connector

plates to the rear supports

Step 3: Attaching the top connector

plates to the support plate

WARNING: The installer of these products must verify that the

mount surface, ceiling or wall, will safely support the combined

weight of all attached equipment and hardware. Video Mount

Products will not be held liable for the improper use or installation

of its products.

Enjoy Your Mount!

7

11

8

Step 4: Attaching the top

connector plates to the ER-1

Step 5: Attaching the rear

supports to the ER-1

2A 2B

7

10

8

4A

3

3

7

6

1A 1B

2A

4A

2A

7

11 1A 7

82A 2

78

2

2B

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur