Vivotek IP7361 Manuel utilisateur
EN-1
English
Warning Before Installation
Contact your distributor in the
event of occurrence.
Refer to your user's manual for the
operating temperature.
Power off the Network Camera as
soon as smoke or unusual odors are
detected.
Do not touch the Network Camera
during a lightning storm.
Do not place the Network Camera on
unsteady surfaces.
Do not drop the Network Camera.
Do not insert sharp or tiny objects
into the Network Camera.
EN-2
Package Contents
1
Software CD
IP7361 with an RJ45 Cable
Quick Installation Guide
Waterproof Connector (for backup
use)
Alignment Sticker / Silica Gel
Wall Mount Bracket
Sun Shield
Power Adapter
Waterproof Connector for RJ45
Ethernet Enclosure
RJ45
Warranty Card
EN-3
English
Physical Description
2
IR LED
Lens
Light Sensor
Power Cord Socket
General I/O
Terminal Block Reset Button
Status LED
SD/SDHC Card Slot
RJ45 Cable
EN-4
1. Attach the alignment sticker to the wall. Drill four holes into the wall. Then hammer the supplied
plastic anchors into the holes and secure the plate with supplied screws.
2. Fix the ͱ-bracket to the side of the Network Camera with two screws.
3. Feed the RJ45 cable through the front opening of the wall mount bracket. (If you want to use
external devices such as sensors and alarms, please refer to the assembling steps on the next
page.)
4. Open the lens cover.
5. Push the spring mortise and hook the bracket onto the groove of the wall mount bracket.
6. Secure the two screws on the other side of the wall mount bracket.
7. Hang the wall mount bracket on the plate.
8. Fix the wall mount bracket with the supplied screw.
9. Adjust the angle of the wall mount bracket to aim at the shooting area.
1
2
7
4
5
3
6
8
9
Hardware Installation
3
EN-5
English
Waterproof Connector
1 Power +12V
2 Digital Output
3 Digital Input
4 Ground
5 AC 24V
6 AC 24V
7 RS485 +
8 RS485 -
1 External MIC In
2 Ground
3 Audio Out
4 Ground
87654321
4321
1. Disassemble the components of the waterproof connector into part (A) ~ (E) as shown above.
2. Open the back cover of the Network Camera.
3. Remove the rubber stopper from the bottom of the Network Camera and secure the screw nut (A)
tightly.
4. If you need extra power for external devices, please feed the power cable through the wall mount
bracket and the waterproof connector (E --> D --> B --> A) as the illustration shown below. Then
connect the power cord to the socket. Note: There are 7 holes on the seal (B), and the widest hole
with a crack on the side is specific for power cord.
5. If you have external devices such as sensors and alarms, feed the cables through the wall mount
bracket and the waterproof connector (E --> D --> B --> A) as the illustration shown below. Then
refer to the pin definition to connect them to the general I/O terminal block. Note: The recom-
mended cable gauge is 2.0 ~ 2.8 mm.
6. Push the seal (B) into the housing (D).
7. Insert the seals (C) into the empty holes on the seal (B) to avoid moisture.
8. Secure the sealing nut (E) tightly.
Components of the Waterproof Connector
Seals (C)
Housing (D)
Sealing Nut (E)
Seal (B)
Screw Nut (A)
Pin Definition
Assembling Steps
3
4
(E)
(D)
(B)
(A)
5
4
7
6
8
(C)
(B)
(D)
(E)
EN-6
Cabling Assembly
4
123
45
6
78
(D) (B)
(C)
(A)
(E)
Components of the Waterproof
Connector
Screw Nut (C)
Housing (D)
Gasket (E)
Seal (B)
Sealing Nut (A)
RJ45 Cable Dimension (unit: mm)
Prepare an Ethernet cable
and strip part of the sheath.
Insert the housing into the
screw nut.
Insert the seal into the housing.
Insert the stripped Ethernet
cable through the sealing
nut and the housing.
Clamp the cable with
an RJ45 plug.
Push the RJ45 plug into the
housing, then secure the
sealing nut tightly.
Attach the gasket to the front
of the housing.
Assembling Steps
Recommended cable gauge: 24AWG
(0.51 mm)
Connect the Ethernet cable to the RJ45 cable and secure the
connectors tightly.
RJ45 Cable Connector
EN-7
English
Network Deployment
5
Power over Ethernet (PoE)
When using a non-PoE switch
Use a PoE power injector (optional) to connect between the Network Camera and a non-PoE
switch.
When using a PoE-enabled switch
The Network Camera is PoE-compliant, allowing transmission of power and data via a single
Ethernet cable. Follow the below illustration to connect the Network Camera to a PoE-enabled
switch via Ethernet cable.
POWER COLLISION
LINK
RECEIVE
PARTITIO N
12345
Non-PoE Switch
PoE Power Injector
(optional)
POWER COLLISION
LINK
RECEIVE
PARTITION
12345
PoE Switch
EN-8
1. Install "Installation Wizard 2" from the Software Utility directory on the software CD.
2. The program will conduct an analysis of your network environment. After your network
is analyzed, please click on the "Next" button to continue the program.
3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network
Cameras on the same LAN.
4. After searching, the main installer window will pop up. Click on the MAC that matches
the one labeled on the side of the camera or S/N number on the label of carton to
connect the Internet Explorer to the Network Camera.
0002D17151CD
1
2
Model No.: IP7361
P/N: 100043690G
F/W Ver.: 0100d
CARTON OF NO. 01
MADE IN TAIWAN
!!0!!
Q'ty: 1 PC S
EAN: 4712123671550
S/N: 0002D17151CD
0002D17151CD
00-02-D1-07-25-8A 192.168.5.151 IP7361
Installation
Wizard 2
IW
2
Assigning an IP Address
6
EN-9
English
For further setup, please refer to the user's manual on the software CD.
Ready to Use
7
1. Access the Network Camera from the LAN.
2. Retrieve live video through a web browser or recording software.
3. Unscrew the zoom controller to adjust the
zoom factor. Upon completion, tighten the
zoom controller.
4. Unscrew the focus controller to adjust the
focus range. Upon completion, tighten the
focus controller.
T
W
∞
N
3
4
Autres manuels pour IP7361
3
Table des matières
Autres manuels Vivotek Caméra de sécurité
Vivotek
Vivotek FD836B-(E)HVF2 Manuel utilisateur
Vivotek
Vivotek SD8364E/ -M Manuel utilisateur
Vivotek
Vivotek IP816A-LPC Manuel utilisateur
Vivotek
Vivotek 4X-IP7142 Manuel utilisateur
Vivotek
Vivotek FD816B-HF2 Manuel utilisateur
Vivotek
Vivotek IB9387-HT-A Manuel utilisateur
Vivotek
Vivotek IP7330 Manuel utilisateur
Vivotek
Vivotek FD8133V Manuel utilisateur
Vivotek
Vivotek ib9381-ht Manuel utilisateur
Vivotek
Vivotek SD9366-EH Manuel utilisateur
Vivotek
Vivotek FE8174V Manuel utilisateur
Vivotek
Vivotek SD8333-E Manuel utilisateur
Vivotek
Vivotek FD8381-EV Manuel utilisateur
Vivotek
Vivotek IP8130W Manuel utilisateur
Vivotek
Vivotek IP3137 Manuel utilisateur
Vivotek
Vivotek WFD Manuel utilisateur
Vivotek
Vivotek FE8191 Manuel utilisateur
Vivotek
Vivotek PZ7131 Manuel utilisateur
Vivotek
Vivotek TS6346-EHL Manuel utilisateur
Vivotek
Vivotek IP7361 Manuel utilisateur
