Vivotek FD7141 Manuel utilisateur

FD7141(V)

EN - 1

English

Power off the Network Camera as

soon as smoke or unusual odors are

detected.

Contact your distributor in the event of

occurrence.

Refer to your user's manual for the

operating temperature.

Warning Before Installation

Do not place the Network Camera on

unsteady surfaces.

Do not touch the Network Camera

during a lightning storm.

Do not insert sharp or tiny objects

into the Network Camera.

Do not drop the Network Camera.

EN - 2

Software CD

FD7141 (FD7141V)

Quick Installation Guide /

Warranty Card

Alignment Sticker /

Ceiling Hole Template Sticker

Bottom Base /

Plastic Cover (FD7141V only)

Power Adapter

Package Contents

L-type Hex Key Wrench / RJ45 Female/Female Coupler / Slica Gel / Screws

Ceiling Hole Template Sticker

Drill hole

EN - 3

English

Tilt Screw SD Card

Slot IR LEDs

Reccessed Reset Button

N.C.

AC24V

Focus Controller

Zoom Controller

Image Adjustment

Screw

Status LED

Light Sensor

Physical Description

Pan Screw

Lens

Inner View

Ethernet 10/100 RJ45 Plug

Audio Out (green)

Microphone In (pink)

Power Cord Socket (black)

General I/O Terminal

Block

Ground

Fan

The fan will operate when the

temparature inside the Network

Camera reaches over 50°C.

f= 3.3~12 mm (FD7141 Lens)

f= 9~22 mm (FD7141V Lens)

EN - 4

Record the MAC address under

the camera base before installing

the camera. Network Camera

Model No: FD7141

Made in Taiwan

This device complies with part 15 of the FCC rules. Operation is subject to

the following two conditions:

(1)This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference

that may cause undesired operation.

Pat. 6,930,709

RoHS

V I

MAC:0002D1083236

Bottom Base

Outer View

Dome Cover

N.C.

AC24V

Camera Base

Hole a~c:

Holes for ceiling mount or for

attaching the bottom base.

EN - 5

English

First, use a screwdriver to loose the three screws and detach the dome cover from the

camera base. Then, follow the steps below to install the camera to either a ceiling or a wall.

Hardware Installation

Ceiling mount with the bottom base

1. Attach the supplied alignment sticker to the ceiling.

2. Using the 10 circles on the sticker, drill 2 pilot holes symmetrically on each side into the ceiling. Then

hammer the four supplied plastic anchors into the holes.

3. Through the four holes on the bottom base, insert the four supplied screws into the corresponding

holes and secure the bottom base with a screwdriver.

4. Feed the cables through hole A or B. If you want to use hole B, remove the rubber stopper with a

screwdriver.

5. Secure the camera base to the bottom base with three supplied screws.

N.C.

AC24V

EN - 6

Wall mount with the bottom base

1. Attach the supplied alignment sticker to the wall.

2. Using the 10 circles on the sticker, drill 2 pilot holes symmetrically on each side into the wall. Then

hammer the four supplied plastic anchors into the holes.

3. Using the four holes on the bottom base, insert the four supplied screws to corresponding holes and

secure the bottom base with a screwdriver.

4. Feed the cables through hole A or B. If you want to use hole B, remove the rubber stopper with a

screwdriver.

5. Secure the camera base to the bottom base with three supplied screws.

EN - 7

English

General Connection (without PoE)

N.C.

AC24V

POWE

OLLIS

ION

LINK

IVE

PAR

TITION

12345

Network Deployment

1. If you have external devices such as sensors and alarms, make the

connection from the general I/O terminal block.

2. Use the supplied RJ45 female/female coupler

to connect the Network Camera to a switch.

Use a Category 5 Cross Cable when Network

Camera is directly connected to PC.

3. Connect the power cable from the Network

Camera to a power outlet.

N.C.

AC24V

N.C.: NoConnector

AC24V: Power in AC 24V

GND: Ground

D I : Digital Input

D O : Digital Output

+12V : Power, 12V DC

GND

+12V

Ceiling mount without the bottom base (Embedded)

1. Attach the supplied ceiling hole template sticker to the ceiling.

2. Open a hole along the inner circle of the sticker.

3. Using the 3 circles on the sticker, drill 3 pilot holes into the ceiling. Then hammer the three supplied

plastic anchors into the holes.

4. Mount the Network Camera to the ceiling and feed the cables through.

5. Using the three holes on the side of the camera base, insert the three supplied screws into the cor-

responding holes and secure them with a screwdriver.

Ceiling Hole Template Sticker

Drill hole

EN - 8

Power over Ethernet (PoE)

POWER COLLISION

LINK

RECEIV E

PARTITION

12345

N.C.

AC24V

PoE Switch

POWER COLLISION

LINK

RECEIV E

PARTITION

12345

N.C.

AC24V

When using a non-PoE switch

Use a PoE power injector (optional) to connect between the Network Camera and a

non-PoE switch.

When using a PoE-enabled switch

The Network Camera is PoE-compliant, allowing transmission of power and data via a

single Ethernet cable. Follow the below illustration to connect the Network Camera to a

PoE-enabled switch via Ethernet cable.

Non-PoE Switch

PoE Power Injector

(optional)

EN - 9

English

Network Camera

Model No: FD7141

Made in Taiwan

This device complies with part 15 of the FCC rules. Operation is subject to

the following two conditions:

(1)This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference

that may cause undesired operation.

Pat. 6,930,709

RoHS

V I

MAC:0002D1083236

1. Install “Installation Wizard 2” from the Software Utility directory on the software CD.

2. The program will conduct an analysis of your network environment. After your network is

analyzed, please click on the “Next” button to continue the program.

3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network

Cameras on the same LAN.

4. After searching, the main installer window will pop up. Click on the MAC that matches the

one labeled on the bottom of your device to connect to the Network Camera via Internet

Explorer.

0002D1083236

Installation

Wizard 2

Assigning an IP Address

Autres manuels pour FD7141

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Vivotek Caméra de sécurité

Vivotek

Vivotek SD83xxE/-M Manuel utilisateur

Vivotek

Vivotek PT3112 Manuel utilisateur

Vivotek

Vivotek BD5336 Manuel utilisateur

Vivotek

Vivotek 9189 Series Manuel utilisateur

Vivotek

Vivotek Supreme MD8563-EH Manuel utilisateur

Vivotek

Vivotek IP8355H Manuel utilisateur

Vivotek

Vivotek FD8361L Manuel utilisateur

Vivotek

Vivotek Supreme SD9374-EHL Manuel utilisateur

Vivotek

Vivotek SD8333-M Manuel utilisateur

Vivotek

Vivotek MA8391-ETV Manuel utilisateur

Vivotek

Vivotek IP7131 Manuel utilisateur

Vivotek

Vivotek Supreme SD9361-EH/EHL Manuel utilisateur

Vivotek

Vivotek CaMate CM48 Series Manuel utilisateur

Vivotek

Vivotek IB9391-EHT Manuel utilisateur

Vivotek

Vivotek IP8336W Manuel utilisateur

Vivotek

Vivotek IB9367-EH Manuel utilisateur

Vivotek

Vivotek FD8161 Manuel utilisateur

Vivotek

Vivotek IP8330 Manuel utilisateur

Vivotek

Vivotek Supreme IP8151 Manuel utilisateur

Vivotek

Vivotek IB8377-H Manuel utilisateur

Vivotek

Vivotek 2M Manuel utilisateur

Vivotek

Vivotek SD83X4E Manuel utilisateur

Vivotek

Vivotek IB9365-EHT Manuel utilisateur

Vivotek

Vivotek IP7142 Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur

Lumens

Lumens VC-A50PNW Manuel utilisateur