Vivo STAND-V102O Manuel utilisateur

Dual Monitor Desk Mount

Scan the QR code with your mobile device or follow the link

for helpful videos and specifications related to this product.

Instruction Manual

https://vivo-us.com/products/stand-v102o

[email protected]om www.vivo-us.com 1-800-371-5654

SKU: STAND-V102O

2 3

ASSEMBLY STEPS

STEP 1

OPTION A: Desk Clamp Install

Assemble base (B) to clamp (C)

using M6x8 bolts (F), and tighten

with 5mm Allen key (H). Unscrew

the large clamp bolts to the “open”

position.

For 3/8” - 2” (10mm - 50mm) desk

thickness, place clamp disks (E)

onto the top of the clamp bolts.

Place assembled base onto edge

of desk and tighten using the 5mm

Allen key.

For 1-1/2” - 3-1/8” (40mm - 80mm)

desk thickness, remove the two

bolts from the back of the clamp

using 5mm Allen key, and then

reassemble clamp to the lower

position. Place clamp disks (E)

onto the top of the clamp bolts.

Place assembled base onto edge

of desk and tighten using the 5mm

Allen key.

PACKAGE CONTENTS

TOOLS NEEDED

14.3lbs

(6.49kg)

DO NOT EXCEED WEIGHT CAPACITY.

Failure to do so may result in serious injury.

WARNING!

Phillips

Screwdriver

A (x2)

Arm

B(x1)

Base

C(x1)

Clamp

M-A (x8)

M4x12

M-B (x8)

M5x12

M-C (x8)

D5 Washer

If you do not understand these directions, or if you have any doubts about the safety of the

installation, please call a qualified technician. Check carefully to make sure there are no missing or

defective parts. Improper installation may cause damage or serious injury. Do not use this product

for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.

We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or

inappropriate use.

D(x1)

Support Plate

E(x2)

Clamp Disk

F (x2)

M6x8 Bolt

G(x1)

3mm Allen Key

H (x1)

5mm Allen Key

OPTION B: Grommet Base Install

Remove large clamp bolts from clamp (C).

If necessary, drill two holes in desk using a

3/8” (10mm) drill bit. The support plate (D)

may be used as a drill guide. Secure base

(B) to desk using clamp bolts with support

plate (D), and tighten using 5mm Allen key

(H). NOTE: Grommet option will fit a desk

thickness of 3/8” - 1-3/4” (10mm - 45mm).

WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

NOTE: SOME HARDWARE MAY NOT BE USED

PER SCREEN

Do not overtighten screw!

4 5

STEP 2

While holding arm (A) in the closed position, cut the shipping tie from each arm.

STEP 4

STEP 5

STEP 3

Place the arms (A) onto the base (B). Tighten the screw on the back of each arm using the

3mm Allen key (G) or a flat blade screwdriver.

Attach two bolts (M-A or M-B) and washers (M-C) to top

mounting holes of each monitor, making sure to leave

1/8” (3mm) of threads exposed.

Align bolts installed to monitor with VESA plate. Secure using two more

bolts (M-A or M-B) and washers (M-C) in the bottom two holes. Tighten all

four bolts using the 5mm Allen key (H) or a Phillips screwdriver. Repeat for

second monitor.

1. Firmly hold the two halves of the spring arm together and

have another person cut o the cable tie from around the

spring arm.

2. Slowly release the pressure on the spring ar and allow it

to gradually stretch to it’s full extension.

6 7

STEP 6 STEP 7

Use cable clips on arms (A) to organize cables.

Adjust gas spring tension in arms (A) and monitor bracket tilt support using 5mm Allen

key (H). Turn gas spring tension adjustment screw counter-clockwise to increase support,

and clockwise to decrease support.

Last Updated: 04/03/2019

If any parts are received damaged or defective, please contact us. We are happy to

replace parts to ensure you have a fully functioning product.

For more VIVO products, check out our website at:

www.vivo-us.com.

Love your new VIVO setup and want to share?

Tag us in your photo! @vivo_us

[email protected]om www.vivo-us.com 1-800-371-5654

Table des matières

Autres manuels Vivo Support et étagère

Vivo

Vivo MOUNT-E-UP44 Manuel utilisateur

Vivo

Vivo MOUNT-POLE01A Manuel utilisateur

Vivo

Vivo STAND-SIT1B Manuel utilisateur

Vivo

Vivo MOUNT-V001GL Manuel utilisateur

Vivo

Vivo MOUNT-SPSB1 Manuel utilisateur

Vivo

Vivo STAND-TV12H Manuel utilisateur

Vivo

Vivo MOUNT-KB05T Manuel utilisateur

Vivo

Vivo STAND-V000U Manuel utilisateur

Vivo

Vivo STAND-TV65A Manuel utilisateur

Vivo

Vivo DESK-E-200W Manuel utilisateur

Vivo

Vivo STAND-V003Y Manuel utilisateur

Vivo

Vivo DESK-V000A Manuel utilisateur

Vivo

Vivo MOUNT-E-MM070 Manuel utilisateur

Vivo

Vivo STAND-TV22B Manuel utilisateur

Vivo

Vivo MOUNT-CR02V Manuel utilisateur

Vivo

Vivo MOUNT-M-FD27 Manuel utilisateur

Vivo

Vivo MOUNT-KB05HD Manuel utilisateur

Vivo

Vivo MOUNT-VP01B Manuel utilisateur

Vivo

Vivo STAND V001B Manuel utilisateur

Vivo

Vivo DESK-V000KL Manuel utilisateur

Vivo

Vivo MOUNT-VW080L Manuel utilisateur

Vivo

Vivo MOUNT-HP32Q Manuel utilisateur

Vivo

Vivo STAND-V000D5 Manuel utilisateur

Vivo

Vivo DESK-V001KE Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur