Vivo STAND-V100A Manuel utilisateur

Silver Pneumatic Arm Single Monitor Desk Mount

Scan the QR code with your mobile device or follow the link

for helpful videos and specifications related to this product.

Instruction Manual

https://vivo-us.com/products/stand-v100a

SKU: STAND-V100A

[email protected]om www.vivo-us.com 309-278-5303

Chat live with an agent!

GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

PACKAGE CONTENTS

TOOLS NEEDED

2.2-19.8lbs

(1-9kg)

DO NOT EXCEED WEIGHT CAPACITY.

Failure to do so may result in serious injury.

Phillips

Screwdriver

A (x1)

Arm

B(x1)

Clamp Brace

C(x1)

Clamp

J (x1)

Support Plate

NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED

D(x1)

Cover

E(x1)

VESA Plate

F (x3)

M6x8mm

G(x4)

Pad

H (x1)

Carriage Bolt

I (x1)

Grommet Base

K (x1)

M8 Nut

M-A (x4)

M4x12

M-B (x4)

M5x12

M-C (x4)

D5 Washer

WARNING!

If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a

qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may

cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do

not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly

or inappropriate use.

TIPOVER WARNING

SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR

STAND.

• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL

USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

O (x1)

6mm Allen

Wrench

L (x1)

M8 Washer

M (x1)

Cable Clip

N (x1)

4mm Allen

Wrench

P (x1)

Wrench

ASSEMBLY STEPS

STEP 1

OPTION A: Clamp Installation

Attach clamp brace (B) to the base of the

arm (A) using M6x8mm bolts (F), and tighten

with the 4mm Allen wrench (N). Apply pads

(G) to each corner of the base.

For 3/8” - 2” (10-50mm) desktop thickness,

place clamp (C) over the pre-installed bolts

in the clamp brace, then tighten bolts using

the 4mm Allen wrench (N).

For 1-3/4” - 3-11/32” (45-85mm) desktop

thickness, remove the screw and clamp

plate from the top of the clamp (C) hand

bolt. Remove the hand bolt, reinsert

through the other side, and reassemble the

clamp plate and screw. Place clamp over the

pre-installed bolts in the clamp brace, then

tighten bolts using the 4mm Allen wrench

(N). Place the mount with clamp on the desk

edge and tighten the hand bolt. Place the

cover (D) on the back of the clamp.

OPTION B: Grommet Installation

Drop the carriage bolt (H) down through the

center hole of the grommet base (I), making

sure the counter-sink holes are on the

underside of the base. Attach the grommet

base with carriage bolt to the base of the

arm (A) using M6x8mm bolts (F), and tighten

with the 4mm Allen wrench (N). Apply pads

(G) to each corner of the base.

If a grommet hole is not present in the

desktop, drill a hole through the desktop

using a 3/8” (10mm) bit. Place the arm

over the hole, then secure by attaching

the support plate (J) to the carriage bolt

protruding from underneath the desk using

the M8 nut (K) with M8 washer (L). Tighten

the M10 nut using the wrench (P).

STEP 2

Attach the VESA plate (E) to the monitor using

bolts (M-A or M-B) with washers (M-C), making

sure the knob is facing towards the top of the

monitor, and tighten with a Phillips screwdriver.

STEP 3

Slide the VESA plate (E) with monitor onto the arm (A), and twist the knob 1/4 turn to lock.

STEP 4

If needed, adjust the gas spring in the arm (A) to support the

monitor using the 6mm Allen wrench (O). While holding the arm

in the straight forward position, turn the screw in back clockwise

to decrease support, and counter-clockwise to increase.

Attach the cable clip (M) to the arm, making sure it is firmly latched in place.

STEP 5

CAUTION - To avoid damage to the monitor

and mount, always keep the arm in a horizontal

position while making adjustments.

STEP 6

Use the cable clip (M) and cover (D) to organize cables.

STEP 7

To limit the arm swivel range, tighten the set screw on the back of the arm (A) using the flat blade

end of the 4mm Allen wrench (N). For no swivel range limit, loosen the set screw.

STEP 8

Tighten or loosen the rotation tension by turning the screws on the back of the VESA plate (E) with a

Phillips screwdriver. Adjust tilt support by turning the bolt on the side of the tilt joint with the 4mm

Allen wrench (N).

LAST UPDATED: 08/26/2020

Open Monday - Friday 7:00am - 7:00pm CST,

our dedicated support team can oer immediate assistance with rapid response times. If any

parts are received damaged or defective, please contact us. We are happy to replace parts to

ensure you have a fully functioning product.

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com

[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M

- 23% within < 15m

- 38% within < 30m

- 61% within < 1hr

- 83% within < 2hr

- 92% within < 3hr

Love your new VIVO setup and want to share?

Tag us in your photo! @vivo_us

AVG. RESOLUTION TIME (within oice hrs): < 15 M

www.vivo-us.com

Chat live with an agent!

AVG. RESOLUTION TIME (within oice hrs): 5M 4S

309-278-5303

Table des matières

Autres manuels Vivo Support et étagère

Vivo

Vivo STAND-VAD2 Manuel utilisateur

Vivo

Vivo DESK-V011F Manuel utilisateur

Vivo

Vivo PP-1-T024D/G Manuel utilisateur

Vivo

Vivo STAND-TV75R Manuel utilisateur

Vivo

Vivo STAND-V012F Manuel utilisateur

Vivo

Vivo MOUNT-KB01 Manuel utilisateur

Vivo

Vivo MOUNT-V00MIC Manuel utilisateur

Vivo

Vivo STAND-V001K Manuel utilisateur

Vivo

Vivo MOUNT-VWKB1 Manuel utilisateur

Vivo

Vivo STAND-SP03B Manuel utilisateur

Vivo

Vivo MOUNT-MSIG24 Manuel utilisateur

Vivo

Vivo STAND-V101G2 Manuel utilisateur

Vivo

Vivo STAND-V100W Manuel utilisateur

Vivo

Vivo MOUNT-KB03N Manuel utilisateur

Vivo

Vivo DESK-M051CB Manuel utilisateur

Vivo

Vivo STAND-V001D Manuel utilisateur

Vivo

Vivo STAND-LAP3 Manuel utilisateur

Vivo

Vivo STAND-V102D Manuel utilisateur

Vivo

Vivo STAND-V001L Manuel utilisateur

Vivo

Vivo DESK-V000KL Manuel utilisateur

Vivo

Vivo MOUNT-ART1 Manuel utilisateur

Vivo

Vivo MOUNT-M-FD37 Manuel utilisateur

Vivo

Vivo STAND-V001Q Manuel utilisateur

Vivo

Vivo DESK-V103E Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur