Vivo MOUNT-V001GLW Manuel utilisateur

White Pneumatic Arm Single Laptop Wall Mount

Scan the QR code with your mobile device or follow the link

for helpful videos and specifications related to this product.

Instruction Manual

https://vivo-us.com/products/mount-v001gl

SKU: MOUNT-V001GLW

[email protected]om www.vivo-us.com 309-278-5303

Chat live with an agent!

GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

ASSEMBLY STEPS

PACKAGE CONTENTS

TOOLS NEEDED

9.9lbs

(4.5kg)

DO NOT EXCEED WEIGHT CAPACITY.

Failure to do so may result in serious injury.

WARNING!

Phillips

Screwdriver

If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a

qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may

cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do

not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly

or inappropriate use.

A(x1)

Arm

B(x2)

Cover

D(x1)

Laptop Tray

WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

STEP 1

OPTION A: Wood Stud Wall

Use a pencil to mark drilling

locations and drill 2.2” (55mm)

deep holes using 3/16” (4.5mm)

bit. Use of a stud finder is

recommended. Mount arm (A) to

wall using ST6.3x55 screws (W-A)

and D6 washers (W-C). Do NOT use

concrete anchors (W-B) for wood

stud installation.

C(x1)

5mm Allen

Wrench

E(x2)

Laptop Arm

NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED

F(x2)

Clip

4.4-19.8lbs

(2-9kg)

LAPTOP MONITOR

G(x4)

M4x8

M-A (x4)

M4x12

M-C (x4)

D5 Washer

M-B (x4)

M5x12

W-A (x2)

ST6.3x55

W-B (x2)

Concrete Anchor

W-C (x2)

D6 Washer

DO NOT INSTALL INTO DRYWALL ALONE. VERIFY YOUR WALL CONSTRUCTION. USE WOOD STUDS TO MOUNT. We

include mounting hardware for brick and concrete walls. If unsure, please contact us at vivo-us.com, email at help@

vivo-us.com, or call us at 309-278-5303.

CAUTION!

STEP 1 (Continued)

STEP 2

Press covers (B) into screw holes.

OPTION A: MONITOR INSTALLATION STEP 1

Install screws (M-A or M-B) with D6 washers

(M-C) in top two holes of the monitor, leaving

3mm of space between the screw heads and

the monitor. Hang monitor with screws over

slots in the VESA plate. Insert screws (M-A or

M-B) with D5 washers (M-C) into lower two

holes and tighten using the Phillips end of the

5mm Allen Wrench (C).

OPTION B: Brick/Concrete Wall

Use a pencil to mark drilling locations

and drill 2.4” (60mm) deep holes

using a 3/8” (10mm) bit. Mount arm

(A) to wall using ST6.3x55 screws

(W-A), concrete anchors (W-B) and D6

washers (W-C).

STEP 2

While holding the arm straight

forward, adjust arm tension by

turning the screw on top of the center

arm joint with the 5mm Allen wrench

(C). Turn clockwise to reduce tension

and counterclockwise to increase.

The tension should be just enough to

hold your monitor in place without

liing itself up. If needed, adjust bolts

on the sides of the hinge behind the

VESA plate to tighten or loosen the

tilt support.

STEP 3

Remove cable covers by removing the

screw underneath each one.

STEP 4

Insert cables and replace covers while

making sure the cables have enough

slack to allow enough free movement

of the arm.

OPTION B: LAPTOP INSTALLATION STEP 1

STEP 5

Adjust monitor position as desired.

Place laptop arms (E) underneath each side of the laptop tray (D), aligning the square holes in the arms

with the edge and long slot on each side. Insert clips (F) through the top to secure the arms, making

sure all 4 locks on each clip are engaged with the square holes in the arms.

STEP 2

Attach assembled laptop holder to

75mm and 100mm holes on the arm

(A) using M4x8 screws (G). Tighten

screws using the Phillips end of the

5mm Allen Wrench (C).

STEP 3

Release the locks on the underside of the laptop arms (E). Extend arms, place laptop in the holder,

then adjust the arms to fit the width of the laptop. Engage locks to secure the laptop. If using a thicker

laptop, turn the front bumpers to the upward position for additional support.

STEP 4

While holding the arm straight forward, adjust arm tension by turning the screw on top of

the center arm joint with the 5mm Allen wrench (C). Turn clockwise to reduce tension and

counterclockwise to increase. The tension should be just enough to hold your laptop in place

without liing itself up. If needed, adjust bolts on the sides of the hinge behind the VESA plate

to tighten or loosen the tilt support.

STEP 5

Remove cable covers by removing the screw underneath each one.

STEP 6

Insert cables and replace covers while making sure the cables have enough slack to allow enough free

movement of the arm.

STEP 7

Adjust laptop position as desired.

LAST UPDATED: 11/04/2021

REV1

Open Monday - Friday 7:00am - 7:00pm CST,

our dedicated support team can oer immediate assistance with rapid response times. If any

parts are received damaged or defective, please contact us. We are happy to replace parts to

ensure you have a fully functioning product.

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com

[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M

- 23% within < 15m

- 38% within < 30m

- 61% within < 1hr

- 83% within < 2hr

- 92% within < 3hr

Love your new VIVO setup and want to share?

Tag us in your photo! @vivo_us

AVG. RESOLUTION TIME (within oice hrs): < 15 M

www.vivo-us.com

Chat live with an agent!

AVG. RESOLUTION TIME (within oice hrs): 5M 4S

309-278-5303

Table des matières

Autres manuels Vivo Support et étagère

Vivo

Vivo STAND-V003T/W Manuel utilisateur

Vivo

Vivo STAND-V002L Manuel utilisateur

Vivo

Vivo MOUNT-PC06L Manuel utilisateur

Vivo

Vivo MOUNT VW100T Manuel utilisateur

Vivo

Vivo MOUNT-SF004 Manuel utilisateur

Vivo

Vivo STAND-V101GT Manuel utilisateur

Vivo

Vivo Sidekiix Manuel utilisateur

Vivo

Vivo STAND-V101G3 Manuel utilisateur

Vivo

Vivo MOUNT-VW70G Manuel utilisateur

Vivo

Vivo MOUNT-PC06B Manuel utilisateur

Vivo

Vivo STAND V002R Manuel utilisateur

Vivo

Vivo MOUNT-PLAY1B-1 Manuel utilisateur

Vivo

Vivo DESK-EXT24 Manuel utilisateur

Vivo

Vivo STAND-V100S Manuel utilisateur

Vivo

Vivo MOUNT-KB08SW Manuel utilisateur

Vivo

Vivo STAND-V002 Manuel utilisateur

Vivo

Vivo DESK-SF01LC Manuel utilisateur

Vivo

Vivo STAND-TV09 Manuel utilisateur

Vivo

Vivo PP-MWS63D-L Manuel utilisateur

Vivo

Vivo STAND-V001T Manuel utilisateur

Vivo

Vivo DESK-E151EB Manuel utilisateur

Vivo

Vivo STAND-V004FG Manuel utilisateur

Vivo

Vivo MOUNT-VW080P Manuel utilisateur

Vivo

Vivo DESK-V000K-M2/G/W Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur