Vivo MOUNT-UVM01 Manuel utilisateur
Universal VESA Adapter Bracket Kit
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-uvm01
SKU: MOUNT-UVM01
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
2
PACKAGE CONTENTS
22lbs
(10kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
A (x2)
Upper Vertical
Bracket
B(x2)
Lower Vertical
Bracket
C(x2)
Upper Support
Bracket
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE MAY NOT BE USED
D(x2)
Lower Support
Bracket
E (x4)
M5x45
Thumbscrew
F (x4)
Compression
Pad
G (x1)
Main Plate
H(x1)
VESA Plate
I(x1)
M6x10mm
Thumbscrew
J(x4)
M4x12
K (x4)
Washer
L (x4)
M5x6
M (x4)
M5x8 Flat
Head
N (x2)
M5x15
O(x2)
M5x16 Carriage
Bolt
P(x2)
M5 Nut
Q (x2)
M5x65
R (x1)
Wrench
S (x4)
Adhesive Pad
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
TOOLS NEEDED
Phillips
Screwdriver
Pencil SUPPORTED MONITOR RANGES :
most 20” - 32” screens
VESA Compatability :
100x100mm
Scissors
3
ASSEMBLY STEPS
STEP 1
Place monitor face down on a flat surface with bottom of monitor facing towards
you. Install power, video and other cables to monitor to assist in determining
needed clearance.
PART A: Preparation
STEP 2
Align bottom of one lower vertical bracket (B) with bottom edge of monitor. Locate hangers
closest to centerline of monitor, then mark the next hanger above center with a pencil.
Mark same hangers on the other lower vertical bracket.
Mark hanger set above center
Monitor Center
B
4
G
✓X ✓X
Buttons
X
Mark Mark
Ports
STEP 3
Hold the main plate (G) to center of back of monitor. Locate and mark entire region on
each side that does not overlap with any buttons or ports.
NOTE: Please be sure to also check for buttons on the bottom edge of the monitor!
✓X ✓X
Buttons
G
Mark Mark
Ports
5
STEP 4
Hold an adhesive pad (S) to the bottom edge of the monitor and trim length of pad to
match monitor. Trim remaining pads to the same length, and apply to inner faces of upper
and lower support brackets (C, D) towards the front.
STEP 1
Slide marked hangers on lower vertical brackets (B) onto the marked slotted region of the
main plate (G). Brackets should be an equal distance from the center if possible. If needed,
move the main plate up or down to clear ports on the monitor.
PART B: Lower Bracket Assembly
S
S
C + D
B B
G
6
STEP 2
Secure the main plate to the brackets using M5x15mm screws (N). If main plate is located
at the highest position, instead use M6x16mm carriage bolts (O) with M5 nuts (P) and
tighten with the wrench (R).
STEP 1 (Continued)
Move the main plate (G) up or down to avoid ports as necessary.
G
R
P
O
Ports
G
7
STEP 1
Place lip of one lower support bracket (D) under monitor edge where it will be installed.
Align lower vertical bracket (B) with first available hole in support bracket above monitor
and insert M5x8mm flat head screw (M). Attach other lower support bracket at same
location to opposite vertical bracket. Do not yet tighten screws. Please note, lower support
brackets have slightly longer lip than upper support brackets.
PART C: Upper Bracket Assembly
Move bracket assembly as close
to monitor as possible.
Hold D against monitor face.
D
Move bracket assembly as close
to monitor as possible.
D
8
STEP 2
Attach upper support brackets (C) to upper vertical brackets (A) using M5x8mm flat head
screws (M) at same hole positions as lower support brackets. Do not yet tighten screws.
STEP 1
Partially slide upper vertical brackets (A) into lower vertical brackets (B).
PART D: Assemble Brackets to Monitor
9
STEP 2
STEP 3
Partially insert M5x45mm thumbscrews (E) into vertical brackets at positions closest to top
and bottom of the monitor where a flat surface is available. Place compression pads (F)
onto ends of thumbscrews, and turn screws until light force is applied to the back of the
monitor. If the monitor is much slimmer on top than at the bottom, instead use M5x65mm
screws for the top two holes. For curved monitors, turn screws evenly to slowly li bracket
assembly into position until assembly fits snug to the monitor.
WARNING! Excessive tightening of upper compression screws on ultraslim monitors
can damage your screen!
For best results, tighten lower compression screws until the mount feels secure and cannot
move relative to your monitor. Then tighten upper compression screws until they just
barely touch the back of your monitor. If mounting your monitor vertically, you can tighten
upper compression screws until the pad cannot slide along the monitor back.
Position assembly on the back of the monitor. Slide upper brackets down, making sure
the upper and lower support brackets are fully engaged with the monitor. Insert M5x6mm
screws (L) into back of vertical brackets and tighten to secure brackets.
All support bracket lips under
monitor edge.
L
10
STEP 3 (Continued)
STEP 4
Making sure upper and lower support brackets are correctly aligned
and holding monitor, tighten M5x8 flat head screws (M) with a Phillips
screwdriver.
Tighten screws M
Tighten screws M
Table des matières
Autres manuels Vivo Support et étagère
Vivo
Vivo MOUNT-KB03B Manuel utilisateur
Vivo
Vivo STAND-V038M Manuel utilisateur
Vivo
Vivo STAND-V002CW Manuel utilisateur
Vivo
Vivo STAND-V106A Manuel utilisateur
Vivo
Vivo MOUNT-E-MM070 Manuel utilisateur
Vivo
Vivo STAND-V002OU Manuel utilisateur
Vivo
Vivo MOUNT-VP01B Manuel utilisateur
Vivo
Vivo STAND-V003FG Manuel utilisateur
Vivo
Vivo VESA MOUNT-AOC1A Manuel utilisateur
Vivo
Vivo STAND-V101L Manuel utilisateur
Vivo
Vivo STAND-V001UVM Manuel utilisateur
Vivo
Vivo PP-MWS63D-T Manuel utilisateur
Vivo
Vivo STAND-TV00T Manuel utilisateur
Vivo
Vivo MOUNT-PLAY1W Manuel utilisateur
Vivo
Vivo PP-MWS63D-L Manuel utilisateur
Vivo
Vivo STAND-SIT1WD Manuel utilisateur
Vivo
Vivo STAND-E-149 Manuel utilisateur
Vivo
Vivo STAND-V200B Manuel utilisateur
Vivo
Vivo MOUNT-PC01 Manuel utilisateur
Vivo
Vivo MOUNT-CR70C Manuel utilisateur
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
