Viking Designer DMOC205 Manuel utilisateur

VIKING RANGE CORPORATION

111 Front Street

Greenwood, Mississippi 38930 USA

(662) 455-1200

PARTS INCLUDED IN THE KIT

1) Frame Assembly 2) Bottom Duct Assembly

QTY 1

3) Screw A (1/2" length)

QTY 10

4) Screw B (1-3/4" length)

QTY 4

5) Screw C (3/4" length)

QTY 2

6) Duct A (1)

QTY 1

7) Duct A (2)

QTY 1

8) Duct A (3)

QTY 1

9) Duct B

QTY 1

10) Duct C

QTY 1

11) Template: QTY 1

Front Frame

QTY 1

Back Frame

QTY 1

INSTALLATION

INSTRUCTIONS

DESIGNER SERIES

CONVECTION MICROWAVE BUILT-IN TRIM KIT

Retain for Future Reference

IMPORTANT - PLEASE READ AND FOLLOW

• Before beginning, please read these instructions completely and carefully.

• Be sure to DISCONNECT THE PLUG of the microwave oven from the electrical outlet before installing the built-in trim kit.

Remove the turntable from the oven cavity.

• Because the kit includes metal parts, caution should be used in handling and installation to avoid the possibility of injury.

• Do not remove permanently afﬁxed labels, warnings, or plates from the product. This may void the warranty.

• Please observe all local and national codes and ordinances.

• The installer should leave these instructions with the consumer who should retain for local inspector’s use and for future

reference.

THIS BUILT-IN TRIM KIT IS DESIGNED FOR USE ONLY WITH VIKING CONVECTION MICROWAVE OVENS SPECIFY-

ING BUILT-IN TRIM KIT DMTK276 OR DMTK306 FOR DESIGNER UNITS ON THE RATING LABEL ON THE BOTTOM

FACE PLATE OF THE OVEN CAVITY.

IF YOUR LOWER CONVENTIONAL OVEN IS NOT LISTED IN THE USE AND CARE MANUAL OF THE MICROWAVE

OVEN, THEN DO NOT INSTALL THE MICROWAVE OVEN ABOVE IT OR IN ANY AREA WHERE HEAT AND STEAM

ARE GENERATED; FOR EXAMPLE, NEXT TO OR ABOVE A CONVENTIONAL RANGE.

SCREW A

DUCT A-2

DUCT A-1

DUCT C

DUCT B

SCREW A

18-11/16"

(47.5 cm)

24-7/8" (63.3 cm)

(12.7 cm)

20-1/8"

(51.1 cm) 11-1/2"

(29.2 cm)

Illustration 1

Illustration 2

Illustration 3

SCREW A

DUCT A-1

DUCT BC SCREW A

Illustration 4

SCREW A

DUCT A-3

DUCT A-2

Illustration 5

CABINET OR WALL CUTOUT

Provide an opening in the wall or cabinet as indicated in

illustration 1. The depth should be a minimum of 20-1/8"

(51.1 cm). The ﬂoor of the opening should be constructed

of plywood strong enough to support the weight of the

oven (about 100 lbs.) and should be level for proper

operation of the oven .

NOTE: While the proper functioning of the oven does not

require that the opening be enclosed (with sides, ceiling

and rear partition), this may be required by local code,

and it is suggested that the local code be checked for

any such requirement.

ELECTRICAL OUTLET LOCATION

Outlet should NOT be in the shaded area as indicated

on illustration 1. At the rear of the opening, provide a

3-pronged, polarized, electrical outlet, 115-120 volt AC,

15 amp or larger.

EXHAUST DUCT ASSEMBLY

1. Insert the edge of DUCT (B) into the hold lip of DUCT

(C). Secure together by using a SCREW (A) provided in

the kit. Remove the existing screw (#1) at upper right

rear of the oven and secure DUCT (C) with the screw

(#1) just removed from the oven. Secure DUCT (B) with

SCREW (A) through the duct and into the original screw

hole in the oven. See illustration 2.

2. Position DUCT (A)-1 on the top of the oven inserting

edge of DUCT (BC) assembly into hole lip of DUCT

(A)-1. Tighten two SCREWS (A), securing DUCT (A)-1

to DUCT (BC) assembly. See illustration 3.

3. Position DUCT (A)-2 on the top of the oven and insert

it into the hold lip of DUCT (A)-1. Secure DUCT (A)-2

to DUCT (A)-1 using two SCREWS (A) provided. See

illustration 4.

4. Position DUCT (A)-3 on top of the oven and insert it

into DUCT (A)-2. Secure DUCT (A)-3 using three screws

(A) provided. See illustration 5.

Illustration 6

SCREW B

Illustration 9

Illustration 7

Illustration 8

BOTTOM DUCT

ASSEMBLY

FOOT

DUCT RECESS

NOTE: CENTER BOTTOM DUCT

ASSEMBLY IN THE OPENING

SCREW

BOTTOM

DUCT

ASSEMBLY

DETAIL A

SCREW C

GAP "A"

GAP "B"

MOUNTING TEMPLATE

1. Align the mounting template center line with the center

of the cutout and the ﬂoor line with the ﬂoor of the

cutout. Tape it into place.

2. For DMTK276, only predrill 4 holes marked “A” with

a 1/16" drill bit. For DMTK306, only predrill 4 holes

marked “B” with a 1/16" drill bit.

3. Remove template from the cabinet.

BOTTOM DUCT ASSEMBLY

1. Place the Bottom duct in the center of the opening so

that gap "A" is equal to gap "B". When the BOTTOM

DUCT ASSEMBLY is in the opening correctly, the

bottom ﬂange will ﬁt tightly against the lower edge of

the opening. See illustration 6.

2. Secure the BOTTOM DUCT ASSEMBLY with the two

(3/4") SCREWS (C). IMPORTANT: Secure screws using

holes on bottom ﬂange.

CABINET INSTALLATION

1. Place the oven adjacent to the wall or cabinet opening.

Plug the power cord into the electrical outlet.

2. Carefully guide the assembled oven into the prepared

opening. Slide the oven on the BOTTOM DUCT

ASSEMBLY. See illustration 7. Avoid pinching the cord

between the oven and the wall. Adjust the position

of the oven so that the feet of the oven are ﬁtted into

the holes of the BOTTOM DUCT ASSEMBLY. See

illustration 8.

FRAME INSTALLATION

Position the BACK FRAME to align with the predrilled

holes that were drilled with the mounting template. Check

that it is level and then secure with two SCREWS (B). See

illustration 9. Secure the bottom portion of the BACK

FRAME with the two remaining SCREWS (B).

Illustration 10

SNAP ATTACHMENT 2" (5.1 cm)

For 27" W and

30" W lower oven

MICROWAVE

CUTOUT

LOWER OVEN

CUTOUT

Illustration 11

FRAME INSTALLATION CONT. OVER OVEN INSTALLATION

TABS

Place the FRONT FRAME, with tabs on top, onto the

BACK FRAME. Secure the FRONT FRAME to the BACK

FRAME by ﬁrmly pushing the front frame onto the back

frame engaging the four (4) snap attachments. See

illustration 10.

Viking Range Corporation

111 Front Street • Greenwood, Mississippi (MS) 38930 USA • (662) 455-1200

Speciﬁcations subject to change without notice.

For more product information, call 1-888-VIKING1 (845-4641), or visit our web site at http://www.vikingrange.com

F20302A (PS0506VR)

TINSEB467MRR0

BASIC SPECIFICATIONS

Microwave Oven Built-In Designer Trim Kits

DMOC205 DMTK276 DMTK306

Overall Width 24-5/8" (62.5 cm) 26-9/16" (67.5 cm) 29-1/2" (74.9 cm)

Overall Height from Bottom 14-7/8" (37.7 cm) 19-13/16" (50.1 cm) 19-13/16" (50.1 cm)

Overall Depth from Rear 19" (48.3 cm) N/A

Oven Interior Width

Height

Depth

Overall

16-1/8"

9-5/8"

16-1/8"

1.5 cu. ft.

(40.9 cm)

(24.4 cm)

(40.9 cm) N/A

Cutout Width N/A Min. 24-7/8" (63.3 cm)

Cutout Height N/A Min. 18-11/16" (47.5 cm)

Cutout Depth N/A Min. 20-1/8" (51.1 cm)

Electrical Requirements 120VAC/60 Hz (UL)

117VAC/60 Hz (CSA) N/A

Max. Amp Usage 1.55 KW

1.5 KW

13 amps (UL)

13 (CSA) N/A

Approx. Shipping Wt. 60 lbs. (27.2 kg) 22.5 lbs. (10.2 kg) 24 lbs. (10.9 kg)

Autres manuels pour Designer DMOC205

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Viking Four à micro-ondes

Viking

Viking VMOS201SS Manuel utilisateur

Viking

Viking RVMH330 Manuel utilisateur

Viking

Viking Built-In Instructions d'utilisation

Viking

Viking CRVMH330 Manuel utilisateur

Viking

Viking RDMOR206SS Manuel utilisateur

Viking

Viking DMOS201 Series Manuel utilisateur

Viking

Viking VMOS201SS Manuel utilisateur

Viking

Viking RDMOS201SS Manuel utilisateur

Viking

Viking Professional VMOC205 Manuel utilisateur

Viking

Viking F20380 Manuel utilisateur

Viking

Viking VMOC206SS Manuel utilisateur

Viking

Viking DMOS201 Series Manuel utilisateur

Viking

Viking Professional VMOS200 Manuel utilisateur

Viking

Viking RVM320 Manuel utilisateur

Viking

Viking Designer Select DESO127 Manuel utilisateur

Viking

Viking RVMH330 Manuel utilisateur

Viking

Viking VMOC206LE Manuel utilisateur

Viking

Viking VMOC506 Instructions d'utilisation

Viking

Viking Designer DMOS200SS Manuel utilisateur

Viking

Viking Professional VMOR205 Manuel utilisateur

Viking

Viking RDMOR200SS Manuel utilisateur

Viking

Viking RDMOS201SS Manuel utilisateur

Viking

Viking Designer DMOS200 Manuel utilisateur

Viking

Viking Designer DMOC205 Manuel utilisateur

Manuels Four à micro-ondes populaires d'autres marques

Daewoo

Daewoo KOG-574R0S Manuel utilisateur

LG MH7040SS Manuel utilisateur

Sharp

Sharp R-895(AL)M Manuel utilisateur

Dometic

Dometic DOTRM13W Manuel utilisateur

Sanyo

Sanyo EM-X680 Manuel utilisateur

Sharp

Sharp R-393M Manuel utilisateur

KitchenAid

KitchenAid KMCX4510 Instructions d'installation

Smeg

Smeg S45MCX1 Manuel utilisateur

Russell Hobbs

Russell Hobbs RHM2044 Manuel utilisateur

Sunbeam

Sunbeam SMW759 Manuel utilisateur

Gallet

Gallet FMOE230S Manuel utilisateur

Bosch

Bosch CEG732X.1B Manuel utilisateur

Dometic

Dometic Roadmate 230 Manuel utilisateur

Samsung

Samsung SJ0396W Manuel utilisateur

Sanyo

Sanyo EM-P494WS Manuel utilisateur

Sharp

Sharp R-240 Manuel utilisateur

Electrolux

Electrolux EMS2840 Manuel utilisateur

Daewoo

Daewoo KOC-984T2S13 Manuel utilisateur