ViewSonic PA502S Manuel utilisateur

PA502S/PA502SP/PA502X/PA502XP

DLP Projector

User Guide

Model No. VS16970/VS16971

IMPORTANT: Please read this User Guide to obtain important information on installing

and using your product in a safe manner, as well as registering your product for future

service. Warranty information contained in this User Guide will describe your limited

coverage from ViewSonic Corporation, which is also found on our web site at http://

www.viewsonic.com in English, or in specic languages using the Regional selection

box in the upper right corner of our website. “Antes de operar su equipo lea cu

idadosamente las instrucciones en este manual”

Compliance Information

FCC Statement

This device complies with part 15 of FCC Rules. Operation is subject to the follow-

ing two conditions: (1) this device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may cause

undesired operation.

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installa-

tion. This equipment generates, uses, and can radiate radio frequency energy, and

if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interfer-

ence will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the

equipment o󰀨 and on, the user is encouraged to try to correct the interference by one

or more of the following measures:

yReorient or relocate the receiving antenna.

yIncrease the separation between the equipment and receiver.

yConnect the equipment into an outlet on a circuit di󰀨erent from that to which the

receiver is connected.

yConsult the dealer or an experienced radio/TV technician for help.

Warning: You are cautioned that changes or modications not expressly approved

by the party responsible for compliance could void your authority to operate the

equipment.

For Canada

CAN ICES-3 (B)/NMB-3(B)

CE Conformity for European Countries

The device complies with the EMC Directive 2014/30/EU and Low Voltage

Directive 2014/35/EU.

Following information is only for EU-member states:

The mark is in compliance with the Waste Electrical and Electronic

Equipment Directive 2012/19/EU (WEEE).

The mark indicates the requirement NOT to dispose the equipment

including any spent or discarded batteries or accumulators as unsorted

municipal waste, but use the return and collection systems available.

If the batteries, accumulators and button cells included with this equipment,

display the chemical symbol Hg, Cd, or Pb, then it means that the battery

has a heavy metal content of more than 0.0005% Mercury or more than,

0.002% Cadmium, or more than 0.004% Lead.

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this unit near water.

6. Clean with a soft, dry cloth.

7. Do not block any ventilation openings. Install the unit in accordance with the

manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves,

or other devices (including ampliers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding type

plug has two blades and a third grounding prong. The wide blade and the third

prong are provided for your safety. If the provided plug does not t into your

outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs.

Convenience receptacles and the point where they exit from the unit. Be sure

that the power outlet is located near the unit so that it is easily accessible.

11. Only use attachments/accessories specied by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specied by

the manufacturer, or sold with the unit. When a cart is used, use

caution when moving the cart/unit combination to avoid injury from

tipping over.

13. Unplug this unit when unused for long periods of time.

14. Refer all servicing to qualied service personnel. Servicing is required when the

unit has been damaged in any way, such as: if the power-supply cord or plug is

damaged, if liquid is spilled onto or objects fall into the unit, if the unit is exposed

to rain or moisture, or if the unit does not operate normally or has been dropped.

iii

Declaration of RoHS2 Compliance

This product has been designed and manufactured in compliance with Directive

2011/65/EU of the European Parliament and the Council on restriction of the use

of certain hazardous substances in electrical and electronic equipment (RoHS2

Directive) and is deemed to comply with the maximum concentration values issued

by the European Technical Adaptation Committee (TAC) as shown below:

Substance

Proposed Maximum

Concentration

Actual Concentration

Lead (Pb) 0.1% < 0.1%

Mercury (Hg) 0.1% < 0.1%

Cadmium (Cd) 0.01% < 0.01%

Hexavalent Chromium (Cr6+) 0.1% < 0.1%

Polybrominated biphenyls (PBB) 0.1% < 0.1%

Polybrominated diphenyl ethers (PBDE) 0.1% < 0.1%

Certain components of products as stated above are exempted under the Annex III

of the RoHS2 Directives as noted below:

Examples of exempted components are:

1. Mercury in cold cathode uorescent lamps and external electrode uorescent

lamps (CCFL and EEFL) for special purposes not exceeding (per lamp):

(1) Short length (≦500 mm): maximum 3.5 mg per lamp.

(2) Medium length (＞500 mm and ≦1,500 mm): maximum 5 mg per lamp.

(3) Long length (＞1,500 mm): maximum 13 mg per lamp.

2. Lead in glass of cathode ray tubes.

3. Lead in glass of uorescent tubes not exceeding 0.2% by weight.

4. Lead as an alloying element in aluminium containing up to 0.4% lead by weight.

5. Copper alloy containing up to 4% lead by weight.

6. Lead in high melting temperature type solders (i.e. lead-based alloys containing

85% by weight or more lead).

7. Electrical and electronic components containing lead in a glass or ceramic other

than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or

ceramic matrix compound.

Macintosh and Power Macintosh are registered trademarks of Apple Inc.

Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks

of Microsoft Corporation in the United States and other countries.

ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered

trademarks of ViewSonic Corporation.

VESA is a registered trademark of the Video Electronics Standards Association.

DPMS and DDC are trademarks of VESA.

PS/2, VGA and XGA are registered trademarks of International Business Machines

Corporation.

Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors

or omissions contained herein; nor for incidental or consequential damages resulting

from furnishing this material, or the performance or use of this product.

In the interest of continuing product improvement, ViewSonic Corporation reserves

the right to change product specications without notice. Information in this docu-

ment may change without notice.

No part of this document may be copied, reproduced, or transmitted by any means,

for any purpose without prior written permission from ViewSonic Corporation.

Product Registration

To fulfill possible future product needs, and to receive additional product information

as it becomes available, please visit your region section on ViewSonic’s website to

The ViewSonic CD also provides an opportunity for you to print the product

registration form. Upon completion, please mail or fax to a respective ViewSonic

office. To find your registration form, use the directory “:\CD\Registration”.

Registering your product will best prepare you for future customer service needs.

Please print this user guide and fill the information in the “For Your Records” section.

For additional information, please see the “Customer Support” section in this guide.

For Your Records

Product Name: PA502S/PA502SP/PA502X/PA502XP

ViewSonic DLP Projector

Model Number: VS16970/VS16971

Document Number: PA502S/PA502SP/PA502X/PA502XP_UG_ENG

Rev. 1A 05-21-18

Serial Number: ________________________________________

Purchase Date: ________________________________________

Product disposal at end of product life

The lamp in this product contains mercury which can be dangerous to you and the

environment. Please use care and dispose of in accordance with local, state or

federal laws.

ViewSonic respects the environment and is committed to working and living green.

Thank you for being part of Smarter, Greener Computing. Please visit ViewSonic

website to learn more.

USA & Canada: http://www.viewsonic.com/company/green/recycle-program/

Europe: http://www.viewsoniceurope.com/eu/support/call-desk/

Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx

Table of Contents

Key safety instructions....1

Introduction.......................3

Projector features ...................................... 3

Shipping contents...................................... 4

External appearance of the projector ........ 5

Device control and functions ..................... 6

Projector Positioning .....12

Choosing a location................................. 12

Projection Dimension............................... 13

Connection...................... 14

Connect to the computer or monitor........ 15

Connecting to Video source devices ....... 16

Connecting to HDMI devices................... 17

To connect the projector to a

Component Video source device:............ 17

Connecting to composite video source

devices .................................................... 18

Operation.........................19

Activate the projector............................... 19

Using the menus...................................... 19

Disabling the password function.............. 21

Setting a password.................................. 21

If you forget your password ..................... 21

Entering the password recall

procedure ................................................ 22

Change Password ................................... 22

Disabling the password function.............. 22

Switching input signal.............................. 23

Changing HDMI input settings................. 24

Adjusting the projected image ................. 25

Perform keystone correction.................... 26

Zoom out to see details ........................... 27

Selecting the aspect ratio ........................ 27

About the aspect ratio.............................. 28

Optimizing the image............................... 29

Using Screen Color ................................. 29

Fine-tuning of image quality in

user modes.............................................. 30

Setting the Presentation Timer ................ 33

Hiding the image...................................... 34

Locking control keys................................ 34

Lamp Settings.......................................... 34

Extending lamp life .................................. 35

Timing of replacing the lamp ................... 36

Replacing the lamp.................................. 36

Operations at high altitudes..................... 36

3D functions............................................. 37

Switch off the projector............................ 37

Menu operations...................................... 38

Description of each menu........................ 41

Maintenance.................... 45

Care of the projector................................ 45

LED Indicator........................................... 46

Troubleshooting .............47

Specications .................48

Projector specications............................ 48

Dimensions.............................................. 49

Ceiling mount installation......................... 49

Timing chart............................................. 50

Disclaimer................................................ 54

Appendix .........................55

IR control table ........................................ 55

Address Code.......................................... 56

RS232 command table............................ 57

Key safety instructions

Design and testing of your projector have been carried out in compliance with the

latest safety standards for information technology (IT) devices. However, it is extremely

important for you to follow the instructions provided in this manual and product labels

during use to ensure user safety.

Safety Instructions

●Please read through this manual before using the projector. Save it for future

reference.

●Do not look straight at the projector lens during operation. The intense light

beam may damage your eyes.

●Refer servicing to qualied service personnel.

●Always open the lens shutter or remove the lens cap when the projector light

source has been switched on.

●In some areas there may be line voltage instability. This projector is designed to

operate safely within a mains voltage between 100 to 240 volts AC, but could fail if

power cuts or surges of ±10 volts occur. In areas where the mains voltage may

uctuate or cut out, it is recommended that you connect your projector through

a power stabilizer, surge protector or uninterruptible power supply (UPS).

●Do not block the projection lens with any objects when the projector is under

operation as this could cause the objects to become heated and deformed or even

cause a re.

●Do not place the projector on an unstable cart, stand, or cable. The product may fall

and sustain serious damages.

●Do not attempt to disassemble this projector. The projector contains high voltage

parts that may cause electrocution or death when it comes in contact with the human

body. Under no circumstances should you ever undo or remove any other covers.

Refer servicing to qualied service personnel.

●Do not place this projector in any of the following environments.

- Space that is poorly ventilated or conned. Allow at least 50 cm clearance from

walls and ensure free ow of air around the projector.

- Locations where temperatures may become excessively high, such as the inside of

a car with all windows rolled up.

- Locations that are too humid, dusty, or smoky may contaminate optical

components, shortening the projector's life span and darkening the image.

- Locations near re alarms

- Locations where temperature exceed 35°C/95°F.

- Locations with altitudes greater than 3000 m (10000 feet).

●Do not block the ventilation holes. If the ventilation holes are seriously obstructed,

overheating inside the projector may result in a re.

- Do not place this projector on a blanket, bedding or any other soft surface.

- Do not cover this projector with a cloth or any other item.

- Do not place inammables near the projector.

●Do not step on the projector or place any objects upon it. These acts may damage the

projector itself as well as cause accidents or personal injury.

●Do not place liquids near or on the projector. Liquids spilled into the projector may

cause damage. If the projector does become wet, please unplug the power cable

from the power socket and contact your local repair center for repairs.

●This product can be mounted on a ceiling suspension mount for back projection.

Use only ceiling suspension mounts that meet the relevant requirements and ensure that

the installation is safe.

●When the projector is under operation, you may sense some heated air and odor from

its ventilation grill. It is a normal phenomenon and not a product defect.

●Do not use the safety lever during transport or installation purposes. The safety lever

should only be used with the anti-theft cables sold on the market.

Safety instructions for ceiling mounting of the projector

We hope you to have a pleasant user experience with our projector. This is why we’re

bringing these safety reminders to your attention to prevent possible damage to person

and property.

If you intend to mount your projector on the ceiling, we strongly recommend that you use a

suitable projector ceiling mount kit and ensure it is securely and safely installed.

There may be safety risks if you fail to use an appropriate projector ceiling mounting kit.

Use of inappropriate connectors or screws of the wrong specications or length may cause

the projector to fall from the ceiling.

You can purchase a projector ceiling mounting kit from the projector dealer. We

recommend buying a safety harness in addition to the mounting kit. The harness should be

securely connected to the anti-theft locking groove on the projector as well as the base of

the ceiling mounting support. This will provide additional protection in case the connectors

of the mounting support becoming loose.

Introduction

Projector features

The projector integrates high-performance optical engine projection and a user-friendly

design to deliver high reliability and ease of use. The projector offers the following

features.

The projector offers the following features.

●The color mode provides different options designed for different projectors.

●Compatible with NTSC, PAL, SECAM and HDTV

●D-Sub 15-pin terminal can be connected to analog video

●Equipped with HDMI connection, supports HDCP (PA501S with no such features)

●Multi-language On-Screen Display (OSD) menus

●Digital keystone correction to correct distorted images

●RS-232 interface supports serial control

●The power saving mode reduces the lamp power consumption by up to 30% when no

input signal is detected for a set length of time.

●Presentation timer for better control of time during presentations

●3D Ready supported

●Select Fast Shutdown

●Color management can be used to adjust the color according to your preferences

●The screen type correction function can be projected on a variety of pre-set color

surfaces

Note

●

The information in this manual is subject to change without notice.

●

Without the express written consent, reproduction, transfer or photocopying of this

document in full or in part is prohibited.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ViewSonic Projecteur

ViewSonic

ViewSonic VS17679 Manuel utilisateur

ViewSonic

ViewSonic LS710HD Manuel utilisateur

ViewSonic

ViewSonic CINE5000 - 1000 Lumens Widescreen DLP Home Theater... Manuel utilisateur

ViewSonic

ViewSonic PJL6243 Manuel utilisateur

ViewSonic

ViewSonic PJ452 - LCD XGA Projector-4.9LBS Manuel utilisateur

ViewSonic

ViewSonic PJ406D Manuel utilisateur

ViewSonic

ViewSonic Office Theater PJL830 Manuel utilisateur

ViewSonic

ViewSonic VS13339VS13340 Manuel utilisateur

ViewSonic

ViewSonic VS17258 Manuel utilisateur

ViewSonic

ViewSonic PJ513D-1 Manuel utilisateur

ViewSonic

ViewSonic PJD5133 Manuel utilisateur

ViewSonic

ViewSonic PRO8500 Manuel utilisateur

ViewSonic

ViewSonic PJ503D - DLP Projector Manuel utilisateur

ViewSonic

ViewSonic VS10872 Guide de démarrage rapide

ViewSonic

ViewSonic LS610WH Series Manuel utilisateur

ViewSonic

ViewSonic PJD7583w Manuel utilisateur

ViewSonic

ViewSonic BabyVision Manuel utilisateur

ViewSonic

ViewSonic PJD5126 Manuel utilisateur

ViewSonic

ViewSonic PJD5483s Manuel utilisateur

ViewSonic

ViewSonic Pro8520HD Manuel utilisateur

ViewSonic

ViewSonic PJ1000 - LCD Projector Manuel utilisateur

ViewSonic

ViewSonic VS17337 Manuel utilisateur

ViewSonic

ViewSonic PJD5152 Manuel utilisateur

ViewSonic

ViewSonic M1 Pro Manuel utilisateur

Manuels Projecteur populaires d'autres marques

iEmmet

iEmmet MP-312 Manuel utilisateur

Epson

Epson VS400 Manuel utilisateur

Sony

Sony VPL-HS10 Marketing Specifications & Features Manuel utilisateur

Sony

Sony VPL-HW65ES Manuel de service

Toshiba

Toshiba TLP-791U Manuel utilisateur

Philips

Philips LC1341 Guide de référence

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur

NEC

NEC NP600S EDU Manuel utilisateur

BenQ

BenQ SH753P Manuel utilisateur

Eiki

Eiki EK-623U series Manuel utilisateur

Epson

Epson PowerLite Pro Cinema 6020UB Manuel utilisateur

Epson

Epson PowerLite Home Cinema 705HD Manuel utilisateur

Christie

Christie LHD700 Manuel utilisateur

Navitar

Navitar FX Manuel utilisateur

InFocus

InFocus LitePro 560 Manuel utilisateur

Sony

Sony SRX-R815P Manuel utilisateur

Vivitar

Vivitar DP1500 X Manuel utilisateur

Acer

Acer C20 Series Manuel utilisateur