ViewSonic VE910B Manuel utilisateur

Model No. VS10715

19” Color TFT LCD Display

Service Manual

ViewSonic VE910/b

ViewSonic

381 Brea Canyon Road, Walnut, California 91789 USA - (800) 888-8583

(VE910_SM Rev. 1a Jun. 2005)

reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or

computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical,

manual or otherwise, without the prior written permission of ViewSonic Corporation.

Disclaimer

ViewSonic makes no representations or warranties, either expressed or implied, with respect to the

contents hereof and specifically disclaims any warranty of merchantability or fitness for any particular

purpose. Further, ViewSonic reserves the right to revise this publication and to make changes from time

to time in the contents hereof without obligation of ViewSonic to notify any person of such revision or

changes.

Trademarks

ViewSonic is a registered trademark of ViewSonic Corporation.

All other trademarks used within this document are the property of their respective owners.

Optiquest is a registered trademark of ViewSonic Corporation.

Revision History

ECR Number Description of Changes

EditorRevision SM Editing Date

Initial Release A. Lu

06/09/05

ViewSonic CorporationConfidential

Do Not Copy VE910/b

TABLE OF CONTENTS

2. Specification

3. Front Panel Function Control Description

4. Circuit Description

6. Troubleshooting Flow Chart

9. Block Diagram

10. Schematic Diagrams

7. Recommended Spare Parts List

1. Precautions and Safety Notices

5. Adjustment Procedure

8. Exploded Diagram and Exploded Parts List

11. PCB Layout Diagrams

ViewSonic CorporationConfidential

Do Not Copy VE910/b

1. Appropriate Operation

(1) Turn off the product before cleaning.

(2) Use only a dry soft cloth when cleaning the LCD panel surface.

(3) Use a soft cloth soaked with mild detergent to clean the display housing.

(4)Use only a high quality, safety approved AC/DC power cord.

(5)Disconnect the power plug from the AC outlet if the product will not be used for a long period of time.

(6) If smoke, abnormal noise, or strange odor is present, immediately switch the LCD display off.

(7) Do not touch the LCD panel surface with sharp or hard objects.

(8) Do not place heavy objects on the LCD display, video cable, or power cord.

(9) Do not use abrasive cleaners, waxes or solvents for your cleaning.

(10) Do not operate the product under the following conditions:

- Extremely hot, cold or humid environment.

-Areas containing excessive dust and dirt.

- Near any appliance generating a strong magnetic field.

- In direct sunlight.

2. Caution

No modification of any circuit should be attempted. Service work should only be performed after you are thoroughly familiar

with all of the following safety checks and servicing guidelines.

3. Safety Check

Care should be taken while servicing this LCD display. Because of the high voltage used in the inverter circuit, the voltage is

exposed in such areas as the associated transformer circuits.

4. LCDModule Handling Precautions

4.1 Handling Precautions

(1) Since front polarizer is easily damaged, pay attention not to scratch it.

(2)Be sure to turn off power supply when connecting or disconnecting input connector.

(3)Wipe off water drops immediately. Long contact with water may cause discoloration or spots.

(4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.

(5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.

(6)Since CMOSLSI isusedinthis module, take care of static electricity and ensure human earth when handling.

(7)Do not open or modify the Module Assembly.

(8)Do not press the reflector sheet at the back of the module in any direction.

(9)In the event that a Module must be put back into the packing container slot after it was taken out of the

container, do not press the center of the CCFL Reflector edge. Instead, press at the far ends of the

CFL Reflector edge softly. Otherwise the TFT Module may be damaged.

(10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate or tilt the Interface

Connector of the TFT Module.

1. Precautions and Safety Notices

ViewSonic CorporationConfidential

Do Not Copy VE910/b

(11) After installation of theTFT Module intoan enclosure(LCDmonitor housing, for example), do not twist or

bend the TFT Module even momentarily. When designing the enclosure, it should be taken into consideration

that no bending/twisting forces may be applied to the TFT Module from outside. Otherwise theTFT Module

may be damaged.

(12) The cold cathode fluorescent lamp in the LCD contains a small amount of mercury. Please follow local

ordinances or regulations fordisposal.

(13) The LCD module contains a small amount of materials having no flammability grade. The LCD module

should be supplied with power that complies with the requirements of Limited Power Source

(IEC60950 or UL1950), or an exemption should be applied for.

(14) The LCD module is designed so that the CCFL in it is supplied by a Limited Current Circuit (IEC60950

or UL1950). Do not connect theCCFL to a HazardousVoltage Circuit.

ViewSonic CorporationConfidential

Do Not Copy VE910/b

5.1. Handling andPlacing Methods

Correct Methods: Incorrect Methods:

Only touch the metal frame of the LCD panel

or the front cover of the monitor. Do not touch

the surface of the polarizer.

Surface of the LCD panel is pressed by fingers

and that may cause“Mura”

Take out the monitor with cushions Taking out the monitor by grasping the LCD

panel. That may cause“Mura”

ViewSonic CorporationConfidential

Do Not Copy VE910/b

Place the monitor on a clean and soft foam pad. Placing the monitor on foreign objects. That

could scratch the surface of the panel or cause

“Mura”

The panel is placed facedown on the lap. That

may cause “Mura”

ViewSonic CorporationConfidential

Do Not Copy VE910/b

1. General Requirements

General Specifications

Test Resolution & Frequency “1280 x 1024” @ 60Hz

Test Image Size Full Size

Contrast and Brightness Controls Factory Default:

Contrast = 70%, Brightness = 100%

2. Signal Interface

Video Interface

Analog Input Connector DB-15 (Analog)

Default Input Connector Defaults to the first detected input

Video Cable Connector DB-15 Pin out Compliant DDC 1/2B.

Video Signals 1. Video RGB (Analog) Separate Sync

Video Impedance 75 Ohms (Analog), 100 Ohms (Digital)

Exclusions Not compatible with interlaced video.

3. Power

Power Supply

Input Voltage Range 90 to 264 VAC

Power Dissipation 40 Watts (Typ.)

4. Electrical Requirements

Horizontal / Vertical Frequency

Horizontal Frequency 30 – 82 KHz

Vertical Refresh Rate 50 – 85 Hz

* For resolution 1280 x 1024, the vertical

Refresh rate up to 75 Hz; for there rest

Resolutions, the vertical refresh rate up

To 85Hz

Maximum Pixel Clock 135 MHz

Sync Polarity Independent of sync polarity.

Timing Table

Item Timing Analog

1 640 x 350 @ 70Hz, 31.5kHz Yes

2 640 x 400 @ 60Hz, 31.5kHz Yes

3 640 x 400 @ 70Hz, 31.5kHz Yes

4 640 x 480 @ 50Hz, 24.7kHz Yes

5 640 x 480 @ 60Hz, 31.5kHz Yes

6 640 x 480 @ 67Hz, 35.0kHz Yes

7 640 x 480 @ 72Hz, 37.9kHz Yes

8 640 x 480 @ 75Hz, 37.5kHz Yes

9 640 x 480 @ 85Hz, 43.27kHz Yes

10 720 x 400 @ 70Hz, 31.5kHz Yes

11 800 x 600 @ 56Hz, 35.1kHz Yes

12 800 x 600 @ 60Hz, 37.9kHz Yes

13 800 x 600 @ 75Hz, 46.9kHz Yes

14 800 x 600 @ 72Hz, 48.1kHz Yes

15 800 x 600 @ 85Hz, 53.7kHz Yes

16 832 x 624 @ 75Hz, 49.7kHz Yes

17 1024 x 768 @ 60Hz, 48.4kHz Yes

18 1024 x 768 @ 70Hz, 56.5kHz Yes

19 1024 x 768 @ 72Hz, 58.1kHz No

20 1024 x 768 @ 75Hz, 60.0kHz Yes

21 1024 x 768 @ 85Hz, 68.67kHz Yes

2. Specification

ViewSonic CorporationConfidential

Do Not Copy VE910/b

22 1152 x 864 @ 75Hz, 67.5kHz No

23 1152 x 870 @ 75Hz, 68.7kHz Yes

24 1280 x 1024 @ 60Hz, 63.4kHz Yes

25 1280 x 1024 @ 75Hz, 79.97kHz Yes

26 1280x 720 @ 60Hz, 45kHz (HDTV) Yes

Changing Modes

Maximum Mode Change Blank Time for image

stability. Note:

1) Excluding “Auto Adjust” time

2) Under DOS mode (640 x 350, 720 x 400 & 640 x

400), there is no “Auto Adjust” feature.

3) The monitor needs to do “Auto Adjust” the first

time a new mode is detected.

Under 5 seconds (Maximum)

1 seconds (Typ.) for recognized timings

1-2 seconds (Typ.) for unrecognized timing

5. LCD Panel

Panel Characteristics

Panel Type M190EN04V5

Type “TFT ACTIVE MATRIX

Active Size 376.32 (H) x 301.056 (V)

Pixel Arrangement RGB Vertical Stripe

Pixel Pitch 0.294 mm

# of Backlights 4 CCFL edge-light (2 top / 2 bottom)

Backlight Life 50,000 Hours (minimum)

Panel Performance

Luminance –

Condition:

CT = 6500K, Contrast = Max,

Brightness = Max

270 cd/m2 (typ. after 30-minute warm-up)

215 cd/m2 (minimum after 30-minute warm-up)

Brightness Uniformity ∆L5=Max 1.3 ∆L5= Maximum Luminance/

Minimum Luminance

Contrast Ratio 550:1 (typ.), 350:1 (minimum)

Color Depth 16.2M colors (RGB 6-bit data+FRC data)

Viewing Angle (Horizontal) 140 degrees @ CR>10

Viewing Angle (Vertical) 135 degrees @ CR>10

Response Time

10%-90% @ Ta=25°C

8 ms (Tr= 5.6 ms, Tf = 2.4 ms) (typ.)

12 ms (Tr= 8.4 ms, Tf =3.6 ms) (maximum)

6. Mechanical

Dimensions

Width 414 mm

Height 407 mm

Depth 219 mm

Monitor Weight 5.4kg / 11.88 lbs

Ergonomics

Tilt Up 20 DEGREES MINIMUM

Tilt Down -5 degrees

Package Specifications

Width 490 mm

Height 570 mm

Depth 145 mm

Gross Weight 6.8kg (14.96lb)

7. Environmental

Environmental Conditions

Operating Temperature 0°C to +40°C

Storage Temperature -20°C to +60°C

Operating Relative Humidity 10% to 90% RH Non-Condensing

Storage Relative Humidity 5% to 90% RH Non-Condensing

Operating Altitude 0 to +3,000 meters

Storage Altitude 0 to +12,000 meters

ViewSonic CorporationConfidential

Do Not Copy VE910/b

Front Control Panel

shown below in detail

Main Menu

With OnView controls

Scrolls through menu options and

adjusts the displayed control.

Also a shortcut to display the

Contrast adjustment control

screen.

Power

On/Off

Displays the control

screen for the highlighted

control.

Also toggles between two

controls on some

screens.

Also a shortcut to Auto

Image Adjust.

Power light

Green = ON

Orange = Power Saving

Displays the Main Menu

or exits the control screen

and saves adjustments.

3. Front Panel Function Control Description

ViewSonic CorporationConfidential

Do Not Copy VE910/b

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ViewSonic Moniteur

ViewSonic

ViewSonic VP2365-LED Manuel utilisateur

ViewSonic

ViewSonic VA1703wb-2 Guide de référence

ViewSonic

ViewSonic VA705M Manuel utilisateur

ViewSonic

ViewSonic VX1935wm Manuel utilisateur

ViewSonic

ViewSonic VA2405-h Manuel utilisateur

ViewSonic

ViewSonic VS13963 Manuel utilisateur

ViewSonic

ViewSonic CD4200 - 42" LCD Flat Panel Display Manuel utilisateur

ViewSonic

ViewSonic VA902 Manuel utilisateur

ViewSonic

ViewSonic VA2703 Manuel utilisateur

ViewSonic

ViewSonic VS18576 Manuel utilisateur

ViewSonic

ViewSonic VA2253S Manuel utilisateur

ViewSonic

ViewSonic VA2419-smh Manuel utilisateur

ViewSonic

ViewSonic VA2756-MHD Manuel utilisateur

ViewSonic

ViewSonic VS11894 Manuel utilisateur

ViewSonic

ViewSonic VG2427WM - 24" LCD Monitor Manuel utilisateur

ViewSonic

ViewSonic ViewBoard IFP50 Series Manuel utilisateur

ViewSonic

ViewSonic VS17729 Manuel utilisateur

ViewSonic

ViewSonic PerfectFlat PF77 Manuel utilisateur

ViewSonic

ViewSonic E655 Manuel utilisateur

ViewSonic

ViewSonic VX2035wm - 20.1" LCD Monitor Manuel utilisateur

ViewSonic

ViewSonic VX2000-1 Manuel utilisateur

ViewSonic

ViewSonic VA1931wa-LED Manuel utilisateur

ViewSonic

ViewSonic E71F Manuel utilisateur

ViewSonic

ViewSonic VA1931WMA Manuel utilisateur

Manuels Moniteur populaires d'autres marques

Linear Acoustic

Linear Acoustic LQ-1000 Manuel utilisateur

AOC

AOC I2579V Manuel utilisateur

Gateway

Gateway FPD1520 Manuel utilisateur

Furuno

Furuno Mu 120c Manuel utilisateur

Asus

Asus VB171D - 17" LCD Monitor Manuel utilisateur

Dell

Dell S2230MX Instructions d'utilisation

Philips

Philips 107C64 Manuel utilisateur

Dell

Dell S2409WFP Manuel utilisateur

EverFocus

EverFocus EN-7517E Manuel utilisateur

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuel utilisateur

Dell

Dell Precision 7680 Mode d’emploi

LG 50PM1M - - 50" Plasma Panel Manuel utilisateur

Bosch

Bosch DDU 9 Manuel utilisateur

Acer

Acer A231HL Manuel utilisateur

Philips

Philips 86BDL4152T Manuel utilisateur

NEC

NEC AccuSync LCD5V Manuel utilisateur

Emay

Emay SleepO2 Manuel utilisateur

IBM

IBM 6360 Instructions d'installation