Viessmann EA1 Guide rapide
5443233 GB 3/2020 Dispose after installation.
Installation and service
instructions
for contractors
VIESMANN
EA1 extension
Function extension
Safety instructions
Please follow these safety instructions closely to prevent accidents
and material losses.
Safety instructions explained
Danger
This symbol warns against the
risk of injury.
!Please note
This symbol warns against the
risk of material losses and envi-
ronmental pollution.
Note
Details identified by the word "Note"
contain additional information.
Installation, commissioning, inspection,
maintenance and repairs must only be
carried out by an authorised, competent
person (heating engineer/installation
contractor).
Before working on the appliance/heat-
ing system, isolate it from the power
supply (e.g. by removing a separate
mains fuse or by means of a mains iso-
lator) and safeguard against unauthor-
ised reconnection.
When using gas as fuel, also close the
main gas shut-off valve and safeguard
against unintentional reopening.
Check for gas tightness after installa-
tion.
Wear suitable personal protective
equipment when carrying out any work.
Repairing components that fulfil a
safety function can compromise the
safe operation of the system.
For replacements, use only original
spare parts supplied or approved by
Viessmann.
Install the components with new gas-
kets.
2
Please dispose of packaging waste in
line with statutory regulations.
Disposal of packaging
5443233
3
Sym-
bol
Meaning
Reference to other document
containing further information
1.
Step in a diagram:
The numbers correspond to
the order in which the steps
are carried out.
Warning of material losses and
environmental pollution
Live electrical area
Pay particular attention.
■ Component must audibly
click into place.
or
■ Acoustic signal
■ Fit new component.
or
■ In conjunction with a tool:
Clean the surface.
Dispose of component correct-
ly.
Dispose of component at a
suitable collection point. Do
not dispose of component in
domestic waste.
Symbols
5443233
4
Spare parts lists
Information about spare parts can be
found at www.viessmann.com/etapp
or in the Viessmann spare part app.
Application
Note
In the following, the different Vitotronic
control units are designated as group
A, B or C.
To find out the control unit designation,
please refer to the type plate on the
control unit or heat generator.
Group A
■ Vitotronic 100, type HC1B
■ Vitotronic 100, type HC2B
■ Vitotronic 100, type KC2B
■ Vitotronic 100, type KC4B
■ Vitotronic 100, type GC7B
■ Vitotronic 200, type HO1B
■ Vitotronic 200, type HO1C
■ Vitotronic 200, type KO1B
■ Vitotronic 200, type KO2B
■ Vitotronic 200, type KW6B
■ Vitotronic 200, type HO1D
■ Vitotronic 200, type HO2B
■ Vitotronic 200, type GW7B
Group B
■ Vitotronic 100, type GC1B
■ Vitotronic 100, type GC4B
■ Vitotronic 200, type GW1B
■ Vitotronic 200-H, type HK1B
■ Vitotronic 200-H, type HK3B
■ Vitotronic 300, type GW2B
■ Vitotronic 300, type GW4B
■ Vitotronic 300-K, type MW1B
■ Vitotronic 300-K, type MW2B
Group C
■ Vitotronic 200, type WO1C
Group D
■ Vitotronic 100, type CC1E, CC1I
■ Vitotronic 200, type CO1E, CO1I
■ Vitotronic 300, type CM1E, CM1I
Symbols (cont.)
5443233
5
1.
2.
Overview of electrical connections
aVG
A
LNL
N
fÖ
SP
aBJ
Ö
[{S
DE [{{]
0-10V f-]
A
[{A
DE [{D
DE
+ -5 61 2 1 2 3 4
AEA1 extension
DE1 Digital input 1
DE2 Digital input 2
DE3 Digital input 3
0 - 10 V 0 - 10 V input
fÖ Power supply
fÖ A Power supply for additional
accessories
aBJ Central fault message facility/
feed pump/DHW circulation
pump (floating switching con-
tact)
aVG KM-BUS to the control unit
Wall mounting
5443233
6
!Please note
Electronic assemblies can be
damaged by electrostatic loads.
Before beginning work, touch
earthed objects, such as heating
or water pipes, to discharge
static loads.
Note
Apply strain relief to on-site cables.
Seal any unnecessary apertures with
cable grommets (not cut open).
Connecting digital inputs (groups A and B)
The following functions can alterna-
tively be connected:
■ External operating program change-
over for each heating circuit
■ External blocking
■ External blocking with central fault
message input
■ External demand with set flow tem-
perature
■ Central fault message
■ Brief operation of the DHW circula-
tion pump
This function is enabled when the input
is closed.
External contacts must be potential-
free. When connecting external con-
tacts, observe the requirements of pro-
tection class II, i.e. 8.0 mm air and
creep path or 2.0 mm insulation thick-
ness to live parts.
Function assignment of inputs DE1 to DE3
Select the input functions by means of
the codes on the heat generator control
unit:
Digital input Control unit coding address
Group A Group B
DE1 3A 5d
DE2 3b 5E
DE3 3C 5F
Depending on the function and the digi-
tal input selected for it, set the following
codes at the Vitotronic control unit:
Overview of electrical connections (cont.)
5443233
7
Function Setting at relevant coding ad-
dress
No function 0
Operating program changeover 1
External demand with set flow temperature 2
External blocking 3
External blocking with fault message input 4
Fault message input 5
Brief operation, DHW circulation pump 6
Complete description of the coding
addresses:
Control unit or heat generator
installation and service instruc-
tions
Assigning the operating program
changeover function to the heating
circuits
Assign the operating program change-
over function for the relevant heating
circuit via coding address d8 at the con-
trol unit:
■ Changeover via input DE1:
Code d8:1
■ Changeover via input DE2:
Code d8:2
■ Changeover via input DE3:
Code d8:3
■ Select the effect of the operating pro-
gram changeover via coding
address d5.
■ Set the duration of the changeover
via coding address F2.
Effect of the "External blocking"
function on the pumps (group A)
■ Select the effect on the internal boiler
circulation pump (Vitotronic, type
HC1B, HC2B, HO1B and HO1C) in
coding address 3E.
■ Select the effect on the relevant heat-
ing circuit pump in coding
address d6.
■ Select the effect on the circulation
pump for cylinder heating (Vitotronic,
group A) in coding address 5E.
Effect of the "External demand"
function on the pumps (group A)
■ Select the effect on the internal boiler
circulation pump (Vitotronic, type
HC1B, HC2B, HO1B and HO1C) in
coding address 3F.
■ Select the effect on the relevant heat-
ing circuit pump in coding
address d7.
■ Select the effect on the circulation
pump for cylinder heating (Vitotronic,
group A) in coding address 5F.
Connecting digital inputs (groups A and B) (cont.)
5443233
8
Set flow temperature for external
demand
■ Select the set flow temperature in
coding address 9b.
Connecting digital inputs (group C)
Function assignment of inputs DE1 to DE3
Input functions are permanently
assigned for the Vitotronic 200, type
WO1C. See the following table:
Input Function
DE1 Swimming pool heating de-
mand
DE2 External blocking
DE3 External demand/external
changeover of operating
status
External contacts must be potential-
free. When connecting external con-
tacts, observe the requirements of pro-
tection class II, i.e. 8.0 mm air and
creep path or 2.0 mm insulation thick-
ness to live parts.
Further details:
Vitotronic 200, type WO1C serv-
ice instructions
Connecting digital inputs (group D)
The following functions can alterna-
tively be connected:
■ External operating program change-
over for each heating circuit
■ External blocking
■ External blocking with central fault
message input
■ External demand with set flow tem-
perature
■ Central fault message
■ Brief operation of the DHW circula-
tion pump
This function is enabled when the input
is closed.
External contacts must be potential-
free. When connecting external con-
tacts, observe the requirements of pro-
tection class II, i.e. 8.0 mm air and
creep path or 2.0 mm insulation thick-
ness to live parts.
Connecting digital inputs (groups A and B) (cont.)
5443233
9
Function assignment of inputs DE1 to DE3
Select the input functions by means of
the parameter settings on the heat gen-
erator control unit:
Digital input Control unit parameters (General
group)
DE1 42
DE2 43
DE3 44
Depending on the function and the digi-
tal input selected for it, set the following
parameters at the Vitotronic control
unit:
Function Settings at parameters 42, 43,
44 (General group)
No function 0
Operating program changeover 1
External demand with set flow temperature 2
External blocking 3
External blocking with fault message input 4
Fault message input 5
Brief operation, DHW circulation pump 6
Complete description of the parame-
ters:
Control unit or heat generator
installation and service instruc-
tions
Assigning the operating program
changeover function to the heating
circuits
Select assignment of the operating pro-
gram changeover function for the rele-
vant heating circuit via parameter 20
(Heating circuit group) at the control
unit:
■ Changeover via input DE1: Parame-
ter 20:1
■ Changeover via input DE2: Parame-
ter 20:2
■ Changeover via input DE3: Parame-
ter 20:3
Connecting digital inputs (group D) (cont.)
5443233
10
■ Select the effect of the operating pro-
gram changeover via parameter 1F
(Heating circuit group).
■ Set the duration of the changeover
via parameter 24 (Heating circuit
group).
Set flow temperature for external
demand
■ Select the set flow temperature in
parameter 0B (General group).
Connecting a circulation pump or a fault message facility
Connection aBJ is floating.
The following components can be con-
nected to plug aBJ:
Groups A, B and D:
■ Feed pump to substation
or
■ DHW circulation pump
or
■ Fault message facility
? ?
fÖaBJ
230 V~
f-]
A
M
1~
A
ACirculation pump or fault message
facility 230 V
Connecting digital inputs (group D) (cont.)
5443233
Autres manuels pour EA1
1
Table des matières
Autres manuels Viessmann Unité de contrôle
Viessmann
Viessmann 5204 Manuel utilisateur
Viessmann
Viessmann VITOSOLIC 100 Manuel utilisateur
Viessmann
Viessmann 5561 Manuel utilisateur
Viessmann
Viessmann SDIO/SM1A Guide rapide
Viessmann
Viessmann VITOCAL 150-A Mode d'emploi
Viessmann
Viessmann LANZ Bulldog Manuel utilisateur
Viessmann
Viessmann 5224 Manuel utilisateur
Viessmann
Viessmann SM1 Guide rapide
Viessmann
Viessmann VITOTRONIC 200 Mode d'emploi
Viessmann
Viessmann 5214 Manuel utilisateur
Viessmann
Viessmann EM-EA1 extension Mode d'emploi
Viessmann
Viessmann Dekamatik-HK1 Manuel utilisateur
Viessmann
Viessmann 5205 Manuel utilisateur
Viessmann
Viessmann VITOTRONIC SPS Mode d'emploi
Viessmann
Viessmann VITOSOLIC 100 Manuel utilisateur
Viessmann
Viessmann VITOTRONIC 200 Mode d'emploi
Viessmann
Viessmann vitotronic 200-h Manuel utilisateur
Viessmann
Viessmann VITOSOLIC 200 Manuel d'instructions
Viessmann
Viessmann VITOTRONIC 200 Manuel utilisateur
Viessmann
Viessmann VIVOTRONIC 050 HK3W Manuel utilisateur
Manuels Unité de contrôle populaires d'autres marques
Festo
Festo Compact Performance CP-FB6-E Manuel de la liste des pièces
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur
JS Automation
JS Automation MPC3034A Manuel utilisateur
JAUDT
JAUDT SW GII 6406 Series Guide rapide
Spektrum
Spektrum Air Module System Manuel utilisateur
BOC Edwards
BOC Edwards Q Series Manuel utilisateur
