Viessmann VITODENS 333 Mode d'emploi
VIESMANN
Service instructions
for heating engineers
Vitodens 333
Type WS3A, 4.2 to 13.0 kW
Compact gas fired condensing boiler
natural gas and LPG version
See applicability on the last page
VITODENS 333
5692 579 GB 11/2004 Please keep safe
Please follow these safety instructions closely to prevent accidents and
material losses.
Safety instructions explained
Danger
This symbol warns against the
risk of injury.
!Important information
This symbol warns against the
risk of material losses and
environmental pollution.
Note
Details identified by the words "Note"
contain additional information.
Warranty
All warranty rights are void if these
service instructions are not observed.
Target group
These service instructions are exclu-
sively designed for qualified person-
nel.
Work on gas equipment must only be
carried out by a registered gas fitter.
Only approved contractors may mod-
ify this equipment for countries other
than those designated on the type
plate. That contractor will then
arrange for the relevant approval in
that country.
Electrical work must only be carried
out by a qualified electrician.
The system must be commissioned by
the system installer or a qualified per-
son authorised by the installer.
Regulations
Observe the following during service
work:
&all legal instructions regarding the
prevention of accidents,
&the TRGI, TRF and special regula-
tions, e.g. those of the BDH,
&all legal instructions regarding
environmental protection,
&the Code of Practice by relevant
trade associations and all local reg-
ulations.
If you notice a smell of gas
Danger
Escaping gas can cause explo-
sionswhichmayleadtoser-
ious injury.
&Do not smoke. Prevent
naked flames and sparks.
Never switch electrical lights
or equipment.
&Open windows and doors.
&Close the gas shut-off valve.
&Remove all personnel from
the danger zone.
&Observe the safety regula-
tions of your local gas sup-
plier which can be found on
the gas meter.
&Notify your heating contrac-
tor from outside the building.
Safety instructions
2
Safety instructions
5692 579 GB
If you smell flue gas
Danger
Flue gas may lead to life-threa-
tening poisoning.
&Shut down the heating sys-
tem.
&Ventilate the boiler room.
&Closealldoorsleadingtothe
living space.
Repair work
It is not permitted to carry out repairs
on parts that fulfil a safety function.
Use only original Viessmann spare
parts, or equivalent parts that have
been approved by Viessmann.
Service work on the heating system
&Isolate the system from mains sup-
ply, e.g. by removing a separate
fuse or by means of a mains electri-
cal isolator, and check that it is no
longer 'live'.
&Safeguard the system against
unauthorised reconnection.
&When using gas as fuel, also close
the main gas shut-off valve and
safeguard against unauthorised
reopening.
Ancillary components, spare and
wearing parts
!Important information
Components which are not
tested with the heating system,
the installation of non-
approved spare parts and
unauthorised conversion may
lead to damage to the heating
system, which may affect their
function and limit our warranty.
For conversions or replace-
ments, use only original parts
from Viessmann or those spare
parts which are approved by
Viessmann.
Safety instructions (cont.)
3
Safety instructions
5692 579 GB
Initial start-up, inspection, maintenance
Steps - initial start-up, inspection and maintenance ..................................... 5
Further details regarding the individual steps .............................................. 7
Coding
Code 1........................................................................................................ 39
Code 2........................................................................................................ 42
Resetting coding to as delivered condition .................................................. 61
Service scans
Service level summary................................................................................ 62
Temperatures, boiler coding card and brief scans ....................................... 63
Checking outputs (relay test) ...................................................................... 67
Scanning operating conditions and sensors ................................................ 69
Troubleshooting
Downloading fault codes history.................................................................. 72
Calling up current fault codes...................................................................... 72
Checking and acknowledging faults ........................................................... 74
Repairs ...................................................................................................... 83
Function description
Constant temperature control unit ............................................................... 94
Weather-compensated control unit.............................................................. 96
Internal extension H1.................................................................................. 98
Extensions for external connections (accessories) ...................................... 99
Control functions ........................................................................................ 102
Designs
Connection and wiring diagrams –internal connections .............................. 107
Connection and wiring diagrams –external connections.............................. 109
Parts lists .................................................................................................. 111
Commissioning/service reports............................................................... 118
Specification............................................................................................. 124
Certificates
Declaration of conformity ............................................................................ 125
Manufacturer's certificate according to the 1st BImSchV [Germany]............. 126
Keyword index .......................................................................................... 127
Index
4
Index
5692 579 GB
For further instructions on individual steps, see pages indicated
Commissioning steps
Inspection steps
Maintenance steps Page
!!!
•1. Filling the heating system ................................................. 7
•2. Venting the boiler.................................................................. 8
•3. Venting the heating system............................................... 8
•4. Filling the siphon with water............................................. 9
•5. Checking the electrical mains connection
•6. Language selection (if required) –only for the
weather-compensated control units ............................. 9
•• 7. Setting the time and date (if required) –only for
weather-compensated control units ............................. 9
••• 8. Pivoting the control unit down to carry out
commissioning and maintenance work........................ 10
••9. Checking the gas type......................................................... 11
•10. Gas type conversion............................................................ 11
••• 11. Function sequence and possible faults........................ 12
•12. Changing the gas type (see separate installation
instructions)
••• 13. Checking static and supply pressure ........................... 13
••• 14. Checking the CO2settings ................................................ 15
•15. Setting the max. output ...................................................... 17
••• 16. Checking all connections on the primary and DHW
side for leaks
••• 17. Checking the burner (recording values on
page 118 of commissioning report)
•18. Checking the balanced flue system for soundness
(annular gap check) ............................................................. 18
•• 19. Removing the burner and checking the burner
gasket (replace gasket every two years)...................... 19
•• 20. Checking the burner gauze assembly........................... 20
Steps - initial start-up, inspection and maintenance
5
Initial start-up, inspection, maintenance
5692 579 GB
Commissioning steps
Inspection steps
Maintenance steps Page
!!!
•• 21. Checking and adjusting the ignition and ionisation
electrodes ................................................................................ 21
•• 22. Cleaning the combustion chamber/heating
surfaces and installing the burner ................................. 22
•• 23. Checking the condensate drain and cleaning the
siphon........................................................................................ 23
•• 24. Checking the neutralising system (if installed)
•25. Testing anode earth current with an anode tester.... 23
•26. Cleaning the DHW cylinder ............................................... 24
•27. Checking and replacing the magnesium anode (if
required)................................................................................... 25
•28. Taking the DHW cylinder back into use ........................ 25
••• 29. Checking the diaphragm expansion vessel and
system pressure
••• 30. Checking the function of all safety valves
••• 31. Checking tightness of electrical connections
••• 32. Checking all gas equipment for soundness at
operating pressure .............................................................. 26
••• 33. Checking the ionisation current ..................................... 26
••• 34. Checking the external LPG safety valve (if
installed)
•35. Matching the control unit to the heating system ...... 27
•36. Connecting the control unit to the LON system
(only for weather-compensated control units) .......... 32
•37. Implementing a user check (in conjunction with
the LON system) .................................................................... 33
•38. Adjusting heating curves (only for weather-
compensated control units).............................................. 34
•39. Instructing the system user .............................................. 38
•40. Scanning and resetting the "Maintenance" display 38
Steps - initial start-up, inspection and . . . (cont.)
6
Initial start-up, inspection, maintenance
5692 579 GB
Filling the heating system
!Important information
Unsuitable fill water increases the level of deposits and corrosion and
may lead to boiler damage.
&Thoroughly flush the entire heating system prior to filling with water.
&Only use fill water of potable quality.
&Softenfillwaterharderthan20°dH(3.58mmol/l).
&An anti-freeze additive suitable for heating systems can be mixed with
the fill water.
1. Check the charge pressure of the
diaphragm expansion vessel.
2. Close the gas shut-off valve.
3. Fill the heating system at the fill
valve in the heating return (on the
connection set or on site). (min.
system pressure > 0.8 bar).
Note
&If the control unit had not already
been switched ON before filling
began: The diverter valve is in
centre position, and the system
will be completely filled.
&If the control unit had already
been switched ON before filling
began: In code 1, set coding
address 2F:2 (see page 39).
The diverter valve will then be in
its central position.
Whilst filling is in progress, the
display shows bF (constant tem-
perature control unit) or "Filling"
(weather-compensated control
unit).
4. Close the boiler fill & drain valve.
5. Set coding address 2F:0.
Further details regarding the individual steps
7
Initial start-up, inspection, maintenance
5692 579 GB
Venting the boiler
1. Close the shut-off valves on the
heating water side.
2. Connect the drain hose on valve A
with a drain outlet.
3. Open valve Aandfillvalveinthe
heating return, and vent at mains
pressure, until no sound of escap-
ingaircanbeheardanymore.
4. Close valve Aand fill valve in the
heating return, and open the pri-
mary shut-off valves.
Venting the heating system
1. Close the gas shut-off valve and
start the control unit.
2. Activate the venting program via
coding address 2F:1.
Note
To call up code 1 and for setting the
coding address, see page 39.
For function and sequence of the
venting program, see page 103.
Whilst venting is in progress, the
display shows "EL" (constant tem-
perature control unit) or "Venting"
(weather-compensated control
unit).
3. Check the system pressure.
Further details regarding the individual steps (cont.)
8
Initial start-up, inspection, maintenance
5692 579 GB
Filling the siphon with water
1. Remove the retaining clip and
siphon A.
2. Fillthesiphonwithwater.
3. Fit siphon Aandsecurewiththe
retaining clip.
Language selection (if required) –only for the weather-com-
pensated control units
1. Press c.
The display shows "Heizkreis aus-
wählen".
2. Press d.
3. After approx. 4 seconds press c.
4. Select the required language
with b.
5. Confirm with d.
Setting the time and date (if required) –only for weather-
compensated control units
Note
During commissioning, or after prolonged time out of use, it may be necessary
to set the time and date, if the time flashes in the display.
1. Set the correct time with a/b.
2. Confirm with d.
3. Set the current date with a/b.
4. Confirm with d.
Further details regarding the individual steps (cont.)
9
Initial start-up, inspection, maintenance
5692 579 GB
Pivoting the control unit down to carry out commissioning
and maintenance work
1. Open flap A.
2. Release side closures Band pivot
control unit Cforward.
3. Release the side screws and pivot
control unit Cdown with its retain-
ing frame D.
Further details regarding the individual steps (cont.)
10
Initial start-up, inspection, maintenance
5692 579 GB
Autres manuels pour VITODENS 333
4
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Viessmann Chaudière
Viessmann
Viessmann VITOCELL 100-V Guide rapide
Viessmann
Viessmann VITOCELL 300B Mode d'emploi
Viessmann
Viessmann VITOLIGNO 300-S Manuel utilisateur
Viessmann
Viessmann Vitodens 200-W System Guide rapide
Viessmann
Viessmann VITOPEND 222 WHSA Manuel utilisateur
Viessmann
Viessmann B1HA Manuel utilisateur
Viessmann
Viessmann VITODENS 100-W B1HE Manuel utilisateur
Viessmann
Viessmann Vitodens 200-W System Guide rapide
Viessmann
Viessmann VITOLADENS 300-W Mode d'emploi
Viessmann
Viessmann Vitodens 300 Manuel utilisateur
Viessmann
Viessmann VITODENS 200 Manuel utilisateur
Viessmann
Viessmann Vitodens 100 WB1 Manuel d'instructions
Viessmann
Viessmann Vitodens 200-W System Guide de démarrage rapide
Viessmann
Viessmann VITODENS 200 Mode d'emploi
Viessmann
Viessmann Vitodens 300 Manuel utilisateur
Viessmann
Viessmann Vitodens 200-W WB2B Series Mode d'emploi
Viessmann
Viessmann VITOLIGNO 300-P Manuel utilisateur
Viessmann
Viessmann VITODENS 200 Manuel utilisateur
Viessmann
Viessmann VITODENS 200 WB2A Note de version
Viessmann
Viessmann VITOCROSSAL 200 Manuel utilisateur
Manuels Chaudière populaires d'autres marques
Vaillant
Vaillant uniSTOR VIH SW GB 500 BES Manuel utilisateur
Radijator
Radijator BIO max 23.1 Manuel utilisateur
Brunner
Brunner BSV 20 Manuel utilisateur
Buderus
Buderus Logamax GB062-24 KDE H V2 Manuel utilisateur
Potterton
Potterton 50e Fiche technique
UTICA BOILERS
UTICA BOILERS TriFire Manuel utilisateur
