Victron energy VE.Direct Manuel technique

Updating the VE.Direct Bluetooth Smart

dongle, on an Android phone or tablet, with

VictronConnect v1.1.5

Introduction

The new version of VictronConnect will update the firmware in the dongle.

This powerpoint explains the procedure for Android devices. The

Make sure to always install the latest version of VictronConnect first!

Download page: https://www.victronenergy.com/support-and-downloads/software

Manual: https://www.victronenergy.com/live/ve.direct:ve.direct_to_bluetooth_smart_dongle

Step 1 – Unpair the dongle

Check your phone/tablet bluetooth

settings and remove it from the paired

devices list if it is on it.

Note: do not pair the dongle during

the update process even if you’re

asked for the PIN code. Just close the

dialog by pressing Cancel.

Step 2 – Start the dongle in boot mode

Disconnect the dongle, and connect it

again while pressing the “Clear PIN”

button.

The red Error LED will be lit, and the

other LED is off.

Name shown in App:

VE.Direct BLE dongle (legacy)

Name shown in Android Bluetooth page:

VE.BL

Step 3 – Open App and search for dongle

The dongle will be listed as shown

on the right.

Press the line with the dongle.

In case the dongle is not listed, go

back to step 2.

Make sure not to wait too long after

powering the dongle in boot-mode:

it will automatically leave boot-

mode after 2 minutes of inactivity.

Step 4 – Open the dongle page

This page will show ->

Press Continue, at the bottom

Do not follow the instructions

‘Disconnect the VE.Direct BLE

dongle… ‘!

Step 5 – Start 1st update

This page will show ->

Press Update, at the bottom

Step 6 – Wait for update to finish

The update will start, wait for it to

complete.

Once finished, the LEDs on the dongle

will blink alternately: red, blue, red, blue,

very fast.

Remember: when asked to pair, press

cancel.

When finished the app will automatically

go back to the device list.

Step 7 - Start 2nd round of updating

Start the 2nd round of updating by

pressing the line.

Step 8 – Start 2nd update

Press Update, at the bottom

Autres manuels pour VE.Direct

1

Table des matières

Autres manuels Victron energy Matériel informatique

Victron energy

Victron energy VE.Direct to Bluetooth Manuel utilisateur

Victron energy

Victron energy VE.Bus Manuel utilisateur

Victron energy

Victron energy VE.Direct Manuel utilisateur

Victron energy

Victron energy VE.Bus Manuel utilisateur

Victron energy

Victron energy VE.Bus BMS V2 Manuel utilisateur

Victron energy

Victron energy Color Control GX Manuel utilisateur

Victron energy

Victron energy VE.Direct to Bluetooth Smart dongle Manuel utilisateur

Victron energy

Victron energy Pytes Manuel utilisateur

Victron energy

Victron energy VE.Direct Bluetooth Smart Dongle Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur