Viconics ZigBee Pro VT8000 Series Manuel utilisateur

ZigBee Pro Module

Installation Guide

VT8000 Series Room Controllers

Optional ZigBee Pro Module (VCM8000V5000P)

ZigBee Module Installation Guide 2

028-0425-01 www.viconics.com | sales@viconics.com November 2014

This guide shows you how to install the ZigBee Pro

wireless module with a VT8000 Series Room Controller.

1. Remove security screw on bottom of Room Controller

cover.

2. Open unit by pulling on bottom of Room Controller

(Figure 1).

3. Carefully remove Room Controllers Motherboard from

casing and turn over.

4. Locate gap in upper-right corner of Room Controllers

Motherboard and locate holes to insert ZigBee Pro

module to Motherboard (Figure 2).

5. Align connector pins on ZigBee Pro module with holes

on Motherboard.

NOTE:ensure alignment of pins is correct so as to not

damage ZigBee Pro module.

6. Gently press ZigBee Pro module into Room Controllers

Motherboard until it ﬁts snugly in place.

NOTE:do not press too hard to avoid damage to ZigBee

Pro module.

7. Gently replace Room Controllers Motherboard into

casing.

8. Gently align cover to top of base and snap in place

from bottom (Figure 3).

9. Install security screw.

Figure-1

Figure-3

Figure-2

ZigBee Module Installation Guide 3

028-0425-01 www.viconics.com | sales@viconics.com November 2014

Quick setup

This short procedure is intended to let you pair a ZigBee sensor with your Room Controller. It assumes that all the back-end conﬁguration

of the stand alone Room Controller acting as coordinator or the Multi-Purpose Manager (MPM) coordinator for the ZigBee network has

already been done, and it assumes that the user is familiar with the Permit Join function and the Wireless Ecosystem screen functions.

PROCEDURE

1. Set Permit Join on your Room Controller (or networked MPM coordinator if used) to On.

2. Go to the ﬁrst unused Zone screen in the Wireless Ecosystem section of the Room Controller’s interface.

3. Insert the battery or remove the pull tab (for contact sensors) to activate the ZigBee sensor

4. Verify that the sensor has joined the network, and that on the Zone screen the Paired ﬁeld status reads Yes.

5. Set the Set function to parameter to the correct setting.

6. Set Permit Join on your Room Controller (or networked MPM coordinator if used) to Off.

7. Conditional to use of door or window contact sensors

a) Go to the ﬁrst screen in the Conﬁguration section of the interface.

b) For window sensor, set UI 16 to Window

c) For door sensor, set UI 17 to Door Dry

8. Physically install the sensor.

TROUBLESHOOTING

If the short procedure described here is insufﬁcient or an MPM or Room Controller needs to be conﬁgured, please refer to the VT8000

Room Controllers ZigBee Pro Wireless Integration Guide available on buildingsdownloads.schneider-electric.com.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Viconics Contrôleurs

Viconics

Viconics VT8000 Series Manuel utilisateur

Viconics

Viconics VTR8300 Series Manuel utilisateur

Viconics

Viconics VT7600W Series Manuel utilisateur

Viconics

Viconics VT7600F Series Manuel utilisateur

Viconics

Viconics VT7200 Series Manuel utilisateur

Viconics

Viconics VT7600 Series Manuel utilisateur

Viconics

Viconics R851B Manuel utilisateur

Viconics

Viconics R820 REV2 Series Manuel utilisateur

Viconics

Viconics COV-PIR-FCU-C-5000 Manuel utilisateur

Viconics

Viconics VT76 Series Manuel d'utilisation et d'entretien

Viconics

Viconics VTR8300 Series Manuel utilisateur

Viconics

Viconics VT8000 Series Manuel utilisateur

Viconics

Viconics VT8000 Series Manuel utilisateur

Viconics

Viconics VT7225 series Manuel utilisateur

Viconics

Viconics VT8000 Series Manuel utilisateur

Viconics

Viconics VTR7300 Series Manuel utilisateur

Viconics

Viconics R851V-4 Manuel utilisateur

Viconics

Viconics VTR7300 Series Manuel utilisateur

Viconics

Viconics VZ8250 Manuel utilisateur

Viconics

Viconics VTR7300 Series Manuel utilisateur

Viconics

Viconics R851V Series Manuel utilisateur

Viconics

Viconics VT8000 Series Fiche technique

Viconics

Viconics VT8600 Series Manuel utilisateur

Viconics

Viconics VC3000 Series Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur